Showline SL BAR 720ZT User manual

SL BAR 720ZT

1
Showline Offices
Document Number:SL BAR 720ZT QuickStart Guide
Version as of: 24-004-3881-00 Draft version
SL BAR 720ZT QuickStart Guide
©2016 Philips Group. All rights reserved.
Dallas
10911 Petal Street
Dallas 75238,TX
Tel [phone]: + - -
Fax [phone]: + - -
Auckland
19-21 Kawana Street
Northcote Auckland 0627,
New Zealand
Tel [phone]: +
Fax [phone]: +
Asia
Unit C 14 F Roxy Industrial Centre, / ,
No. 41-49 Kwai Cheong Road
Kwai Chung N T Hong Kong, . .,
Tel [phone]: +
Fax [phone]: +
Europe
Rondweg zuid 85
Winterswijk 7102 JD
The Netherlands
Tel [phone]: + ( ) -
www.philips.com/showline
SL BAR 720ZT Q S GUICK TART UIDE
SL BAR 720ZT QuickStart Guide

SL BAR 720ZT
2
About Quickstart Guide
Included Items
Each includes the following items:SL BAR 720ZT
Figure 1 Included Items:
Warnings and Notices
When using electrical equipment basic safety precautions should always be followed including the following, :
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
Do not use outdoors.
Do not mount near gas or electric heaters.
Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized personnel.
The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.
Do not use this equipment for other than intended use.
Refer service to qualified personnel.
SAVE THIS DOCUMENT FOR FUTURE REFERENCE READ COMPLETELY BEFORE INSTALLING AND USING PRODUCT! !
WARNING:.You must have access to a main circuit breaker or other power disconnect device before installing any wiring Be sure that
power is disconnected by removing fuses or turning the main circuit breaker off before installation. Installing the device with power on may
expose you to dangerous voltages and damage the device. A qualified electrician must perform this installation.
WARNING: Refer to National Electrical Code and local codes for cable specifications Failure to use proper cable can result in damage to.®
equipment or danger to personnel.
WARNING: This equipment is intended for installation in accordance with the National Electric Code and local regulations It is also.®
intended for installation in indoor applications only Before any electrical work is performed disconnect power at the circuit breaker or. ,
remove the fuse to avoid shock or damage to the control. It is recommended that a qualified electrician perform this installation.
Service and Maintenance
For all service and maintenance issues, please contact your local Showline office or an Authorized Service Center.
Power Requirements
The operates on input voltages from 100 to 240 .SL BAR 720ZT AC VAC
SL BAR 720ZT
QuickStart Guide
( )this document
This Quickstart Guide is intended for a knowledgeable user to unpack, install, and use in a short time period. For the completeSL BAR 720ZT
manual in format, please visit our web site at : and click the user manual download link on the product page. ThePDF www.philips.com/showline
complete manual provides you all information related to accessories, menu structures, channel mapping/modes,and care for your new luminaire.DMX
SL BAR 720ZT Q S GUICK TART UIDE
QuickStart Guide
WARNING ON OFF: This unit does not contain an / switch. Always disconnect power input cable to completely remove power from unit when not in use.

3
Maximum amount of units that may be daisy chained is A 3 units 100 15 Amps or B 9 units 240 15 Amps Refer to- ( ) ( ) ( ) ( ).VAC VAC
Table1for detailed information at various voltages.
Note:For wiring of input connector refer toAC , .
Connecting 720ZT to PowerSL BAR AC
Table 1 Voltage vs Current: .SL BAR 720ZT
WARNING:*These figures are based on the Maximum Allowable Input Current of 15 Amps. Do not overload circuits!
IMPORTANT AC POWER CONNECTION NOTES:
DO NOT CONNECT OTHER TYPES OF LUMINAIRES OR DEVICES!
Connecting Power
Units can be powered in one of two ways:
Direct connection to a power source using an input cable. For wiring of input connector, refer toAC AC AC Connecting SL BAR 720ZT
to PowerAC .
Connection from the output of another . When using this method, it is very important not to connect any other type of equipment.AC SL BAR 720ZT
Connecting Luminaires to PowerSL BAR 720ZT LED AC
Ta ble 2 Input Connections:AC
Wire Color
WARNING:
Purpose
WARNING: Only connect other to the Output (Thru) connector ofSL BAR 720ZT AC the other 720ZT.SL BAR
Table 2, Input ConnectionsAC describes how to connect power to your . Field wiring of the isSL BAR 720ZT SL BAR 720ZT
straight forward. A total of 3 wires/conductors is supplied to this unit.
100 180 4.00 2.22 36
47
47
58
58
69
6
47
110 190 3.64 2.11
160 240 2.50 1.67
150 230 2.67 1.74
140 220 2.86 1.82
130 210 3.08 1.90
120 200 3.33 2.00
170 2.35
Only use approved cable types.
When using the daisy-chain connection method, only connect to Output Connection of .SL BAR 720ZT AC SL BAR 720ZT
Do not overload circuits!
Do not connect to dimmed circuits.SL BAR 720ZT
Brown/Black
Blue/White
Green-Yellow/Green
Main/Line(100 to 240 )VAC
Neutral
Ground(Earth)
SL BAR 720ZT
SL BAR 720ZT Q S GUICK TART UIDE
QuickStart Guide
AC Power Operation
When connected to an source the unit operates on 100 to 240 volts 10 auto ranging The luminaire contains an auto ranging power supply, (+/- %, - ). - .AC AC
Each luminaire can draw up to 400 Watts.
Voltage
( )AC
Voltage
( )AC
Total
Current(A)
Total
Current(A)
Maximum
number of units
that can be linked
together*
Maximum
number of units
that can be linked
together*
AC InputAC Output
Neutral
AC Input Connector (on unit)
Main /
Ground / Earth
Line
AC Connector
(on side of unit)
AC Output Connector (on unit)
Neutral Main /
Ground / Earth
Line
AC Connector
(on side of unit)

Mounting Luminaire
Truss / Hanging Applications
The SL BAR 720ZT is provided with the ability to hang via truss hooks, clamps, etc. sold separately( ).
Figure 2 Hanging Application:
4SL BAR 720ZT Q S G
UICK TART UIDE
SL BAR 720ZT
QuickStart Guide
LCD Display and Menu System
The ’s Display and Menu System provides local control for accessing the following fixture’s settings:SL BAR 720ZT LCD
Presets Standard and User Defined( )
Color Filter
Effects Chases preloaded and user defined( - )
Strobe Timing/
Settings
Lock Fixture to prevent changes( )
Password
Status
Note:If there are multiple luminaires in a system changes would need to be made at each Menu as desired For, .LCD
SL BAR 720ZT menu structure, please refer to the complete user manual
SL BAR 720ZT
Home (menu settings)
Edit a Preset Edit a Chase
DMX512 Addressing
Return to Main Screen
LEFT Arrow Button UP Arrow Button
OK (Check Mark) Button
DOWN Arrow Button
RIGHT Arrow Button
LCD Display
NOTE:Menu rotates with orientation of Luminaire and
menu buttons are always in the same position with(
rotation of menu)
To rotate menu 180 degrees manually from current
orientation press and hold the two center buttons for 2,
seconds.
Figure 3 Menu System:
Upon power up the will display the main screen showing the product type name If is enabled the, / . ,LCD DMX
programmed address will appear after power up.
Omega Moun t (x2)
(supplie d with luminaire )
Luminaire Yoke
SAFETY CABLE: Is sold separately and recommended
for all hanging installation and may be required by
national and local codes. Use enclosure handles for
safety cable anchor points for this fixture.