Showline SL BAR 720ZT User manual

SL BAR 720ZT

SL BAR 720ZT Installation & User’s Manual
Version as of: 26th Dec, 2016 Rev1.0
2016 Philips Group. All rights reserved.
Showline Offices
Showline - Dallas
10911 Petal Street
Dallas, TX 75238
Tel: [phone]
Fax: [phone]
Showline - Europe
Marssteden 152
Enschede 7547 TD
The Netherlands
Tel: [phone]
Fax: [phone]
Showline - Auckland
19-21 Kawana Street
Northcote, Auckland 0627
New ZealandU.S.A
Tel: [phone]
Fax: [phone]
Showline - Asia
Unit C, 14/F, Roxy Industrial Centre
No. 41-49 Kwai Cheong Road
Kwai Chung, N.T., Hong Kong
Tel: [phone]
Fax: [phone]
Website:
www.philips.com/showline
The material in this manual is for information purposes only and is subject to change without notice. Showline assumes
no responsiblitity for any errors or omissions which may appear in this manual. For comments and suggestions regarding
corrections and/or updates to this manual, please visit the Showline website at or contact yourwww.philips.com/showline
nearest Showline office.
Note: Information contained in this document may not be duplicated in full or in part by any person without prior written
approval of Showline. Its sole purpose is to provide the user with conceptual information on the equipment mentioned. The use of
this document for all other purposes is specifically prohibited.
Document Number: SL BAR 720ZT User’s Manual

Additional Resources for DMX512
For more information on installing DMX512 control systems the following publication is available for purchase,
from the United States Institute for Theatre Technology (),"USITT Recommended Practice for DMX512 A Guide:
for Users and Installers 2nd edition ISBN USITT Contact Information,"(: ). :9780955703522
USITT
315 South Crouse Avenue Suite 200,
Syracuse NY 13210-1844,
Phone [phone] or 1.315.463.6463:
www usitt org..
Showline Limited Two Year Warranty-
Showline offers a two year limited warranty of its luminaires against defects in materials or workmanship from the-
date of delivery A copy of the Showline two year limited warranty containing specific terms and conditions can be.-
obtained by contacting your local Showline office.
Warnings and Notices
When using electrical equipment, basic safety precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
Do not mount near gas or electric heaters.
Equipment should be mounted in locations and at heights where it will not readily be subject
to tampering by unauthorized personnel.
The use of accessory equipment not recommended by the manufacturer may cause an unsafe
condition.
Do not use this equipment for other than intended use.
Refer service to qualified personnel.
WARNING: You must have access to a mains circuit breaker or other power disconnect device
before installing any wiring. BE sure that power is disconnected by removing fuses or turning the
mains circuit breaker off before installation. Installing the device with power on may expose you
to dangerous voltages and damage the device. A qualified electrician must perform this installation.
WARNING: Refer to National Electrical Code and local codes for cable specifications.
Failure to use proper cable can result in damage to equipment or danger to personnel.
WARNING: This equipment is intended for installation in accordance with the Nation Electric
Code and local regulations. It is also intended for installation in indoor applications only. Before
any electrical work is performed, disconnect power at the circuit breaker or remove the fuse to
avoid shock or damage to the control. It is recommended that a qualified electrician perform this
installation.
Installation & User’s ManualSL BAR 720ZT
IMPORTANT INOFRMATION

TABLE OF CONTENTS
Showline Offices Inside Front Cover
IMPORTANT INFORMATION
Warnings and Notices
Additional Resources for DMX512
Showline Limited Two Year Warranty-
TABLE OF CONTENTS
PREFACE
About this Manual
Included Items
SL BAR 720ZT OVERVIEW
SL BAR 720ZT Components
INSTALLATION AND SET UP
Connecting Power
Connecting SL BAR 720ZT to AC Power
Truss / Hanging Applications
Floor Mounting
Connecting to the DMX512 Network
Mounting Luminaire
OPERATION AND PROGRAMMING
LCD Display and Menu System
LCD Display and Menu System Operation
SL BAR 720ZT Menu Tree
Quick Selection Buttons
Edit a Preset Button
Edit a Chase Button
DMX Address Button
Dimming Curve Selection
Master Slave Operational Mode/
DMX CONTROL
RDM PARAMETER IDs
RGBW 8 Bit Mode-
RGBW 8 Bit Group Mode-
RGBW 16-Bit Mode
RGBW 16-Bit Group Mode
Color Mode
Color Group Mode
DMX Timing Channel Detail
SL BAR 720ZT DMX Mapping
SL BAR 720ZT RDM Parameter IDs
CLEANING AND CARE
Special Cleaning and Care Instructions
Front Lens Cleaning
Service and Maintenance
TECHNICAL SPECIFICATIONS
Operational Specifications
Luminaire Dimensions
Table of contents
2
1
1
1
3
3
4
6
6
8
8
7
8
9
10
11
13
13
13
13
14
15
16
17
20
24
25
26
27
16
33
36
36
36
37
37

PREFACE
1. About this Manual
The document provides installation and operation instructions for the following products:
Please read all instructions before installing or using this product. .Retain this manual for future reference
Additional product information and descriptions may be found on the product specification sheet.
Note: The SL BAR 720ZT luminaire works from 100 to 240 VAC (auto-ranging).
2. Included Items
Each SL BAR 720ZT luminaire includes the following items:
SL BAR 720ZT Luminaire
SL ZT LuminaireBAR 720
SL BAR 720ZT Luminaire
Quick Start Guide
3
About this Manual
Installation & User’s ManualSL BAR 720ZT

SL BAR 720ZT Overview
4
1.SL BAR 720ZT COMPONENTS
Common Luminaire Components
LCD Display Menu System/
Figure 2 LCD Display & Menu System:
Note For Menu operation and programming details refer to:,""LCD Display and Menu System on page 9.
Front of Unit Rear of Unit
AC Input
Fan(x2)
High Power LEDs
Arm
AC Output
DMX/RDM THRU DMX/RDM IN
Rj45 Socket (x2)
SL BAR 720ZT
Home (menu settings)
Edit a Preset Edit a Chase
DMX512 Addressing
Return to Main Screen
LEFT Arrow Button UP Arrow Button
CHECK MARK (Accept) Button
DOWN Arrow Button
RIGHT Arrow Button
LCD Display
NOTE:The menu rotates with the orientation of
luminaire and the menu buttons are always in
the same position with rotation of menu()
To rotate the menu degrees from the current orientation180 ,
press and hold the two center buttons for seconds2.
LCD Display / Menu System
SL BAR 720ZT OVERVIEW
Figure 1: SL BAR 720ZT Common Components
Installation & User’s Manual SL BAR 720ZT

5
Installation and Set Up
INSTALLATION AND SET UP
1 Power Requirements.
The SL BA R 720ZT Luminaire operates on AC input voltages from 100 to 240 VAC.
WARN ING! The SL BAR 720ZT luminaire does not have an ON/OFF switch. Always disconnect power input cable
to completely remove power from the luminaire when not in use.
AC Power Operation
When connected to an AC source, the unit operates on 100 to 240 volts AC (+/- 10%, auto-ranging). The luminaire
contains an auto ranging power supply Each luminaire can draw up to 380 Watts-. .
WARNING Maximum amount of fixtures that may be daisy chained is A 3 units 100 120VAC or B 9 units!-()~()
230 ~ 240VAC (10 Amps).
Note For wiring of AC input connector refer to:,"Connecting SL BAR 720ZT to AC Power" on page 6.
2 Connecting Power.
Units can be powered in one of two ways:
Direct connection to an AC power source using an AC input cable For wiring of the AC input connector refer to.,
Connection from the AC output of another SL BAR 720 ZT When using this method it is very important not.,
to connect any other type of equipment device.
WARN ING! Only connect other SL BAR 720ZT luminaires to the AC Output (Thru) connector of an
Installation & User’s ManualSL BAR 720ZT
Table 1: SL BAR 720ZTVoltage (VAC) vs. Current*
""Connecting SL BAR 720ZT to AC Power on page 6.
SL BAR 720ZT luminaire.
100 180 3.80 2.11 37
47
58
58
59
69
6
47
110 190 3.45 2.00
160 240 2.38 1.58
150 230 2.53 1.65
140 220 2.71 1.73
130 210 2.92 1.81
120 200 3.17 1.90
170 2.23
Voltage
()AC
Voltage
()AC
Total
Current(A)
Total
Current(A)
Maximum
number of units
that can be linked
together*
Maximum
number of units
that can be linked
together*

Connecting SL BAR 720ZT to AC Power
6
Connecting SL BAR 720ZT to AC Power
Table 2 describes how to connect power to your SL BAR 720ZT. Field wiring of the SL BAR 720ZT LED
The following wiring scheme is required:
Figure 3 720ZT AC Input & Output Connections:SL BAR
Brown Main/Line(100 to 240VAC)
Blue Neutral
Green/Yellow Ground (Earth)
Table 2: SL BAR 720ZTAC Input Connections
Installation & User’s Manual
Wire Color Purpose
SL BAR 720ZT
Luminaire is straight-forward A total of 3 wires conductors need to be brought to the unit./ .
AC InputAC Output

Connecting to the DMX512 Network 7
3 Connecting to the DMX512 Network.
Basic DMX512 installation consists of connecting multiple SL BAR 720ZTs together (up to 32 luminaires in)
"-" . (daisy chain fashion A cable runs from the control console or DMX512 control source) to the DMX connector
on the first SL BAR 720ZT. Another cable runs from the other DMX connector on the first unit to a DMX
connector on the next SL BAR 720ZT (or DMX512 device to be controlled).
Figure 4 720ZT DMX512 Input Output Connections:/SL BAR
Note For more information on DMX512 networking and systems refer to:,""Additional Resources for DMX512 on
page 1 "DMX CONTROL" on page 16. For SL BAR 720ZT DMX Mapping, refer to .
Figure 5: SL BAR 720ZT- DMX512 Connections
DMX512 Conections
Note: Remaining pins on each connector are not used.
Installation & User’s ManualSL BAR 720ZT
DMX512 Signal
Common (Drain)
DMX512-
DMX512+
XLR Pin Color
1
2
3Red
White
Black
DMX/RDM THRU DMX/RDM IN

Mounting Luminaire
8
4 Mounting Luminaire.
Truss Hanging Applications/
The SL BAR 720ZT is provided with the ability to hang via truss hooks, clamps, etc. (sold separately). Simply
attach hook clamp etc to the SL BAR 720ZT yoke in the provided M12 holes. It is recommended,,.
(and may be required by local and national safety codes) to use and install a safety cable (sold separately) as illustrated in
Figure 6. When hanging the fixture, be sure to leave enough space around the luminaire to allow proper, uninterrupted
airflow for cooling and movement. Refer to for spacing (dimensional) requirements."Luminaire Dimensions" on page 36
Note Mounting hooks clamps safety cables etc are sold separately or by others For mounting accessories:,,,. .
available for this product, refer to "Accessories" on page 3.
Figure 6 Mounting the Fixture Hanging Applications:-
Installation & User’s Manual SL BAR 720ZT
Omega Mount (x2)
(supplied with luminaire)
Luminaire Yoke
SAFETY CABLE: Is sold separately and recommended
for all hanging installation and may be required by
national and local codes. Use enclosure handles for
safety cable anchor points for this fixture.

OPERATION AND PROGRAMMING 9
OPERATION AND PROGRAMMING
1.LCD Display and Menu System
SL BAR 720ZT
The SL BAR 720ZT’s LCD Display and Menu System provides local control for accessing
the following fixture’s settings:
Presets Standard and User Defined()
Color Filter
Effects Chases preloaded and user defined(- )
Strobe Timing/
Settings
Lock Fixture to prevent changes()
Password
Status
Note:If there are multiple luminaires in a system changes would need to be made at each LCD Menu as desired For,.
SL BAR 720ZT menu structure see,.""SL BAR 720ZT Menu Tree on page 11
Upon power up the LCD will display the main screen showing the product type name If DMX is enabled the,/.,
programmed address will appear after power up.
Figure 7: LCD Display and Menu System
SL BAR 720ZT
Home menu settings()
Edit a Preset Edit a Chase
DMX512 Addressing
Return to Main Screen
LEFT Arrow Button UP Arrow Button
OK Button()Check Mark
DOWN Arrow Button
RIGHT Arrow Button
LCD Display
NOTE:Menu rotates with orientation of Luminaire and
menu buttons are always in the same position with(
rotation of menu)
To rotate menu 180 degrees manually from current
orientation press and hold the two center buttons for 2,
seconds.
Installation & User’s ManualSL BAR 720ZT

LCD Display and Menu System Operation
10
2. LCD Display and Menu System Operation
The LCD Display Menu system consists of several categories Use the Menu.Buttons to access and make changes to
the menu items When the desired menu item is reached press the desired Menu Button to display the menu options.,
and to navigate and configure the menu options as required.
To navigate and access menu settings selections/:
Step 1.Make sure unit is powered and turned on.
Step 2.Press the desired button as shown in(Figure 8).to access menu categories
Step 3.Use UP DOWN LEFT RIGHT arrow buttons to||| .navigate through the various options and settings
Step 4.Make changes as desired.
Press CHECK MARK OK button to accept changes() .
Figure 8 LCD Display and Menu System:
SL BAR 720ZT
Home menu settings()
Edit a Preset Edit a Chase
DMX512 Addressing
Return to Main Screen
LEFT Arrow Button UP Arrow Button
OK Button()Check Mark
DOWN Arrow Button
RIGHT Arrow Button
LCD Display
NOTE:Menu rotates with orientation of Luminaire and
menu buttons are always in the same position with(
rotation of menu)
To rotate menu 180 degrees manually from current
orientation press and hold the two center buttons for 2,
seconds.
Installation & User’s Manual SL BAR 720ZT

SL BAR 720ZT Menu Tree 11
Continue on next page
3. SL BAR 720ZT Menu Tree
Figure 9: SL BAR 720ZT Menu Tree(Part 1)
Installation & User’s ManualSL BAR 720ZT
Built-i atte 1-32nP rn
MA MEIN NU
Strobe/T ingim
Focus Timing 0.2 S- i60 M n
Preset
Effects
CloFo r ilter Co hru 43)lorFilter(0t
Master Intensity 0-100%
Strobe xxxx
Duration
Intensity Timing 0.2 S in-60 M
P hru 31)reset X(0 t
Chase
Speed 0.2 S in-30 M
1thru 10
Master Intensity 0-100%
0-100%Master tensityIn
Pr et X/Color Filter Xes
0-100%
Pixel hite 0-100%1-6_W
0-100%Pixel en1-6_Gre
0-100%Pixel d1-6_Re
Pixel lue1-6_B
Tilt 0-65535
Zoom 0-255
0-100%
0-65535
0-255
0-100%
0-100%
0-100%
0-100%
Ne Swtep
Delete pSte
Zoom Timing 0.2 S in-60 M
0.2 S in-60 M
0--85
Co ilor T ming
Master tensityIn
Pixel d1-6_Re
Pixel en1-6_Gre
Pixel lue1-6_B
Pixel hite1-6_W
Tilt
Zoom
Tilt 0-65535
Zoom 0-255
Tilt 0-65535
Edit Step x (1 thru 100)
B ilt-uinChase
Edit Chas (1 thru 8)ex
Select Chas (1 thru 8)exUse ser Cha
Master Intensity 0-100%
Fade 0-100%
Zoom 0-255

SL BAR 720ZT Menu Tree
12
DM ArtNETX>
Fee ck ONdba
OFF
Zoom Offset o +100-100 t
Colo oderM
-100 to +100
Tilt Offset o +100-100 t
****
Chase(1 thru 18)
Co hru 43)lorFilter(1t
P hru 32)reset X(1 t
1111
2222
Net
Stub-Ne
Universe
LE upD Gro
Eng hlis
On/30S/1Min/
5Min/ i10M n
La cst A tion
Hold
Off
Auto
Yes
No
Other Information RDM UID 0X000000000000
0-100%
Red
PssOre K Run
PssOre K Run
PssOre K Run
Max Intensity 0-100%
xx elsius degreeC
83 Celsius degree
86 Celsius degree
xx elsius degreeC
PssOre K Run
Max_Value
0-100%
PssOre K Run
PssOre K Run
0-100%
Warni wng Lo
Warni ghng Hi
Mi aluen_V
0-255
PssOre K Run
0-100%
0-100%
Blue
Firmware Version Re 0v0.
xx elsius degreeC
NoLFactoryoad
Pr et & Chasees
Pr ected No
otFactory Default
Power-upGeneral
Security
Settings
Powe velr-up Le
Enter ssPINPa
Level IN2P
Level IN1P
Status
Lock xtureFi
Pordassw
Flip DisplayDi yspla
When no DMX
Yes(to lock Fixture)LOCK oAre y u sure?
Oimeff T
Tes t S eqAll
LE empsDT
Tilt
Strobe
LEDs
Zoom
Pixel 1-6
LE nt LevelD Curre
Master tensityIn
ArtNEN Settings dress1IP Ad
Protocol iority ArtNET>DMXPr
Otffse
IP Address2 0-255
IP Address3 0-255
IP Address4 0-255
Power Up
Di esabl
1or6
RGBW t Mode8-bi
1to512
Mode
Fa ntrolnCo
Svice PanOffseter
Inca scentnde
linear
Srequa
Ma tser
S-Curve
L ked/Level 1-3oc
/isd able Password
Auto
OFF
ON
3333
La est S t
Tperatureem
Enter Pass Level 1-3PIN
No
DMX
Assddre
DM ableXEn
Tperatureem
Green
La ge Selectngua
Tilt
Encoder
Zoom
Map
White
Ca rationlib
Level IN3P
Movement Tilt 0-65535
No
Dimming Curve
(DM 8BXit)
Enable
Yes
PL-Curve
Slave
Normal
RGBW t Mode16-bi
DIM sponseRe
Inv Tilt
OFF
Yes
0-255
0-255
0-15
0-15
Enterthismeun, must enter superPa NssPI
Figure 10: SL BAR 720ZT Menu Tree(Part 2)
Installation & User’s Manual
Continued from
previous page
SL BAR 720ZT

Quick Selection Buttons 13
4 Quick Selection Buttons.
When in Manual Mode the SL BAR 720ZT's features can be accessed via the on board LCD menu system or,-
via three quick select buttons:
Edit a Preset Button
Edit a Chase Button
DMX Address Button
Edit a Preset Button
To edit and save a preset:
Step 1 Press Edit a Preset button.. .Current preset will be shown
Step 2 Use LEFT and RIGHT arrow buttons to scroll through all presets..
Step 3 Once at desired preset use UP and DOWN arrows to access.,
() . ,highlight preset parameters Once in desired parameter use LEFT
and RIGHT arrow buttons to adjust parameter value as desired.
Step 4 Once all values are adjusted as desired, press OK (Check Mark) button..
Step 5 Save preset menu option will appear Use LEFT..and RIGHT arrow buttons to .select preset number
Step 6 If saving preset press OK (Check Mark) button. Confirm choice., .
Step 7 Preset is now saved..
Edit a Chase Button
To edit and save a chase:
Step 1 Press Edit a Chase button.. .Current chase will be shown
Step 2 Use LEFT and RIGHT arrow buttons to scroll through all chases.
().Built In and User Chases
Note:For Built In Chases only the Speed and Fade parameters may be,
changed and saved For User Chases.,Chase Number Total Steps Speed and,,,
Fade Parameters may be changed and saved.
Step 3 Once at desired chase use UP and DOWN arrows to access highlight chase parameters Once in desired., ().
parameter use LEFT and RIGHT arrow buttons to adjust parameter value as desired,.
Step 4 Once all values are adjusted as desired, press OK(Check Mark) button..
Step 5 Save chase menu option will appear Use LEFTand RIGHT arrow buttons to select chase number.. .
Step 6 If saving chase press OK Check Mark) button. Confirm choice..,(
Step 7 Chase is now saved..
DMX Address Button
To edit and save a DMX address:
Step 1 Press DMX Address button Current DMX Address will be shown.. .
Step 2 Press OK Check Mark button to highlight a digit in the DMX.( )
address.
Step 3 Use LEFT and RIGHT arrow buttons to scroll through all digits..
Step 4 Once at desired digit use UP and DOWN arrows to change.,
highlighted digit Once digit is set use LEFT and RIGHT arrow buttons to set other digits in DMX address., .
Step 5 Once all digits are set in DMX address, press OK(Check Mark) button..
Step 6 DMX will display and is saved..
Edit a Preset
H
S
I
C
12%
0%
43%
HSI Mode
Edit a Preset
Built In Chase 8
Total Steps
Speed
Fade
24
8S
70%
Edit a Chase
Address
255
DMX Address
Installation & User’s ManualSL BAR 720ZT

Dimming Curve Selection
14
Figure 11: SL BAR 720ZT Dimmer Curves
Through the menu, you are able to select one of four dimming curves:
Linear Curve
PL_Curve
S_Curve
Square Curve
Linear Curve
S_Curve
PL_Curve*
Square Curve
DMX Value
DMX Value
Lumen Output
Lumen Output
Lumen Output
Lumen Output
DMX Value
DMX Value
*PL Curve follows the dimming curve of Philips Selecon
PL series LED luminaires.
Installation & User’s Manual SL BAR 720ZT

Master / Slave Operational Mode 15
6 Master Slave Operational Mode./
The Master / Slave Operational Mode allows one SL BAR 720ZT to act as the "Master" unit and all other
connected units are controlled by this unit. When a unit is set to "Slave" mode, it will only listen to and follow any
commands sent from a Master unit Only one Master unit is allowed in this type of operation"". "" .
Figure 12: SL BAR 720ZT- Master / Slave Configuration
Master Unit Slave Unit Slave Unit
Note: For more information on DMX512 networking and systems, refer to "Additional Resources for DMX512" on
page 1. "DMX CONTROL" on page 16.For SL BAR 720ZT DMX Mapping, refer to
Installation & User’s ManualSL BAR 720ZT
DMX512
DMX512 (out from first
to second luminaire)
DMX512 (out to the next
(from console or
control device) luminaire or DMX512 controlled
device)

16 DMX Control
DMX CONTROL
This section contains information for operating the luminaire using DMX control in Simple 8-bit, RGBW 8-bit,
RGBW 16-bit or HSIC (Hue, Saturation, Intensity and Color Correction) modes. For Menu options and detailed
information, see "LCD Display and Menu System” on page 9.
Note: These tables assume a DMX start address of 1. When a different starting address is used, this address becomes
channel 1 function and other functions follow in sequence.
1. SL BAR 720ZT DMX Mapping
RGBW 8-Bit Mode
Table 3 provides DMX channel mapping of all DMX512 control values when the SL BAR 720ZT LED
Luminaire is in RGBW 8-bit DMX512 mode (as set by the luminaire’s menu system).
Table 3: SL BAR 720ZT DMX Channel Mapping (RGBW 8 - Bit Mode)
Installation & User’s Manual SL BAR 720ZT
DMX Patameter Range DMX Range % Defaults* Description
1
2
3
4Color Presets
Tilt - High Byte
Tilt - Low Byte
Master Intensity 0-255
0-255
0-255
0-255
0-100%
0-100%
0-100%
0-100%
08 bit control for Intensity of LED settings.
0
Preset 0 (OFF)
Preset 1
DMX 0-4
DMX 63-64
DMX 61-62
DMX 59-60
DMX 57-58
DMX 55-56
DMX 53-54
DMX 51-52
DMX 49-50
DMX 47-48
DMX 45-46
DMX 43-44
DMX 41-42
DMX 39-40
DMX 37-38
DMX 35-36
DMX 33-34
DMX 31-32
DMX 29-30
DMX 27-28
DMX 25-26
DMX 23-24
DMX 21-22
DMX 19-20
DMX 17-18
DMX 15-16
DMX 13-14
DMX 11-12
DMX 9-10
DMX 7-8
DMX 5-6
DMX 65-66
DMX 67-68
Preset 30
Preset 29
Preset 28
Preset 27
Preset 26
Preset 25
Preset 24
Preset 23
Preset 22
Preset 21
Preset 20
Preset 19
Preset 18
Preset 17
Preset 16
Preset 15
Preset 14
Preset 13
Preset 12
Preset 11
Preset 10
Preset 9
Preset 8
Preset 7
Preset 6
Preset 5
Preset 4
Preset 3
Preset 2
Preset 31
Channel OFF(disabled)
Variable color Presets as below
0-65535 0-100% 32768 16-bit control of Tilt

Table 3: SL BAR 720ZT DMX Channel Mapping (RGBW 8 - Bit Mode)
DMX Patameter Range DMX Range % Defaults* Description
4Color Presets 0-2550-255 0-100%0-100% 0
CF_1_White 10000K
CF_2_White 8000K
DMX 69-70
DMX 129-130
DMX 139-140
DMX 149-150
DMX 202-204
DMX 127-128
DMX 137-138
DMX 147-148
DMX 125-126
DMX 135-136
DMX 145-146
DMX 123-124
DMX 121-122
DMX 119-120
DMX 117-118
DMX 115-116
DMX 113-114
DMX 111-112
DMX 109-110
DMX 107-108
DMX 105-106
DMX 103-104
DMX 101-102
DMX 99-100
DMX 97-98
DMX 95-96
DMX 93-94
DMX 91-92
DMX 89-90
DMX 87-88
DMX 85-86
DMX 83-84
DMX 81-82
DMX 79-80
DMX 77-78
DMX 75-76
DMX 73-74
DMX 71-72
DMX 131-132
DMX 141-142
DMX 151-152
DMX 205-207
DMX 157-171
DMX 214-216
DMX 226-228
DMX 241-243
DMX 133-134
DMX 143-144
DMX 153-154
DMX 208-210
DMX 172-186
DMX 217-219
DMX 229-231
DMX 244-246
DMX 250-252
DMX 155-156
DMX 211-213
DMX 223-225
DMX 238-240
DMX 187-201
DMX 220-222
DMX 235-237
DMX 232-234
DMX 247-249
DMX 253-255
CF_31_0
CF_41_0
CF_30_0
CF_40_0
CF_29_0
CF_39_0
CF_28_0
CF_38_0
CF_27_0
CF_37_0
CF_26_0
CF_36_0
CF_25_0
CF_35_0
CF_24_0
CF_34_0
CF_23_0
CF_33_0
CF_22_0
CF_21_0
CF_20_0
CF_19_0
CF_18_0
CF_17_0
CF_16_0
CF_15_0
CF_14_0
CF_13_0
CF_12_0
CF_11_Moroccan Pink
CF_10_White 2700K
CF_9_White 3000K
CF_8_White 3200K
CF_7_White 4000K
CF_6_White 4500K
CF_5_White 5000K
CF_4_White 5600K
CF_3_White 6500K
CF_32_0
CF_42_0
CF_43_0
Chase 1
Chase 9
Chase 8
Chase 7
Chase 6
Chase 5
Chase 4
Chase 3
Chase 2
Chase 10
User Chase 1
CF_0_Color OFF
Rotate CW Fast Slow
Rotate ACW Slow Fast
Random Color Fast Slow
User Chase 1
User Chase 1
User Chase 1
User Chase 1
User Chase 1
User Chase 1
User Chase 1
Master / Slave Operational Mode 17
Installation & User’s ManualSL BAR 720ZT

DMX Patameter Range DMX Range % Defaults* Description
5
6
10
11
12
13
14
7
8
9
Strobe
Duration
Control
Red1-6
Green1-6
Blue1-6
White1-6
Zoom
Focus Timing
Timing
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0-100%
0
0
0 Functions of the SL Series products. Set control channel
value to desired action, hold value for at least 5s, then turn
to 0. Set control channel value to 0 without scaling.
0
0
0
0
8 bit control of Red LEDs from 0 to full.
8 bit control of Green LEDs from 0 to full.
8 bit control of Blue LEDs from 0 to full.
8 bit control of White LEDs from 0 to full.
0
255
255
Strobe’s duration Range is 0-85
Variable control of zoom
Timing control of Tilt
Allows for timing control of Intensity/Color/Zoon. Channel
should default to 255 for smoothest actions using console
and/or manual faades.- See Timing Chart for more details.
Control strobe operations as below
DMX 189-255
DMX 196-197
DMX 194-195
DMX 192-193
DMX 134-191
DMX 132-133
DMX 130-131
DMX 128-129
DMX 13-127(fastest)
DMX 11-12
DMX 8-10
DMX 6-7
DMX 3-5
DMX 0-2
Pulse - Range
Pulse - Fast Rand
Pulse - Med Rand
Pulse- Slow Rand
Pulse + Range
Pulse + Fast Rand
Pulse + Med Rand
Pulse + Slow Rand
Strobe Range
Fast Rand
Med Rand
Slow Rand
Closed
Open
DMX253-255
(DMX Value -1)/3 +1
DMX 1-3
DMX 0-2
85
x
1
0
DMX 95-250
DMX 90-94
DMX 85-89
DMX 80-84
DMX 75-79
DMX 70-74
DMX 45-49
DMX 40-44
DMX 35-39
DMX 30-34
DMX 10-14
DMX 5-9
DMX 0-4
Fixture Reset
Reserves(Future use)
Fan_OFF
Fan_Auto
Calibration_ON
Calibration_OFF
Dimming Curve_PL-Curve
Dimming Curve_S-Curve
Dimming Curve_Square
Dimming Curve_Linear
DIM Response_Incandescent
DIM Response_Normal
Default Setting on Console
18 DMX Control
Installation & User’s Manual SL BAR 720ZT
Table 3: SL BAR 720ZT DMX Channel Mapping (RGBW 8 - Bit Mode)