Shure PSM 200 User manual

PSMR200
Personal Monitor System User Guide
>>E2 >>P2R >>P2T
Model PSM200 User Guide
27B8792 (BJ)
2002, Shure Incorporated Printed in U.S.A.

ENGLISH
12
TROUBLESHOOTING
PROBLEM SOLUTION
No sound at the receiver Check the power cord on the TransMixer and make sure it is
powered on.
Make sure both the TransMixer and the P2R Receiver are set to
the same frequency channel.
Make sure the earphones are plugged in to the receiver and the
volume is up.
Make sure the Receiver is on and the battery is good.
Check the incoming audio connections on the TransMixer.
Low receiver range Try to maintain line-of-sight between the TransMixer and Receiver
antennas.
Try another frequency in case interference is limiting the range.
Check for television channel interference. More information is
available at www.shure.com.
Receiver sounds fuzzy or distorted Make sure no other TransMixers or wireless transmitters are oper-
ating on your frequency.
Make sure the TransMixer input level is lighting yellow LEDs for
optimum performance.
Make sure you are using a fresh battery in the P2R.
Low audio output at the receiver Make sure the TransMixer input level is lighting yellow LEDs for
optimum performance.
Make sure the P2R Receiver’s volume knob is up.
ACCESSORIES
Furnished Accessories
P2T TransMixer
AC Adaptor PS20, PS20E, PS20UK. . . . . . . . . . . . . . . . . . . . .
Single Mount Rack Bracket 53A8484. . . . . . . . . . . . . . . . . . . . .
Dual Mount Rack Bracket 53B8484. . . . . . . . . . . . . . . . . . . . . .
Straddle Bars 53A8443. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hardware Kit 90AD8100. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
P2R Receiver
1/4-inch mono 20 foot cable 90B4677. . . . . . . . . . . . . . . . . . .
Optional Equipment
AuxPander:
The Shure AuxPander auxiliary expander extends the capabili-
ties of a standard mixing console by providing eight additional
auxiliary sends. It is designed ideally for use with multiple per-
sonal monitoring systems.
P4M:
The P4M is a highly versatile four–channel, two–bus stereo
mic/line mixer designed to optimize personal (in–ear) monitor
systems in live performance applications.
SPECIFICATIONS
PSM200 System
RF Carrier Frequency Range
518–865 MHz (country dependent)
Operating Range
100 m (300 ft.) under optimal conditions
Audio Frequency Response
30 Hz to 12 kHz (+/–3 dB); earphone dependent
Total Harmonic Distortion (1 kHz)
<1% typical (Ref. ±35 kHz deviation)
Modulation
FM ±35 kHz Deviation (Nominal)
Signal-to-Noise Ratio
80 dB typical (A-weighted)
Operating Temperature
–7°C to +49°C
(+20°F to +120°F)
P2T TransMixer
RF Output Power
30 mW (+15 dBm) typical conducted (country dependent)
Modulation Limiter
Internal peak limiter (>10:1 hard knee compression)
Antenna
1/4 Wavelength, semi-rigid, PCB Mount
Current
170 mA maximum
Dimensions
220 mm x 140 mm x 40 mm (8.6 in. x 5.6 in. x 1.7 in.)
Net Weight
370 g (13 oz.)

ENGLISH
13
P2T Audio Input
Connector Type: XLR/1/4-inch combo
Configuration: electronically balanced
Actual Impedance: 1 kΩ
Nominal Input Level: –25 dBu @ 1/2volume
(12 o’clock)
Maximum Input Level: –5 dBu @ 1/2volume
(12 o’clock)
Pin Assignments: XLR: 2=hot; 3=cold, 1=ground
1/4: Tip = hot, Ring = cold,
Sleeve=ground
Phantom Power Protection? Yes: Up to 52 Vdc
P2T Audio Outputs
Passive connection parallel with input.
Connector Type: XLR
Configuration: electronically balanced
Pin Assignments: 2 = hot ; 3 = cold, 1 = ground
Phantom Power Protection? Yes: Up to 52 Vdc
Power Requirements
Operating voltage 12-18 Vdc
Supplied with one of the following external power supplies:
Model PS20: 120 VAC, 60 Hz input.
Model PS20E, Model PS20UK: 230 VAC, 50/60 Hz input.
P2R Receiver
RF Sensitivity
–109 dBm typical
Squelch Threshold
–102 dBm typical
Antenna
Attached Whip
Audio Input Connector
Connector Type: 1/4-inch Mono
Impedance: 1 MΩ
Maximum Input Level: LO = +0 dBu
HI = –10 dBu
Frequency Response: 30 Hz to 20 kHz (+/–3 dB);
earphone dependent
Power Requirements
9 V alkaline battery, Duracelltype MN1604 recommended
Battery Life
Volume Dependent
Wired (RF Off): 6 hours
Wireless (RF On): 4 hours
Audio Output Connector
1/8inch (3.5 mm)
Minimum Load Impedance
8 Ω
Net Weight
100 g (3.52 oz.), less battery
Overall Dimensions
122 mm x 73 mm x 32 mm
(4.809 in. x 2.875 in. x 1.251 in.)
PSM200 Channel Frequencies
The PSM200 is available in four frequency groups, each coordinated to work in a specific geographic region. You can find the frequency
group for your system printed on the rear panel of the P2T TransMixer. For more information on which frequencies can be used in your area,
call our Applications Group at 847-866-2525, Shure Europe at 49-1731-72140, Shure Asia at 852-2893-4290, or visit the Technical Support
section at www.shure.com.
CHANNEL
H2
(518-554)MHz
North America,
Europe
R8
(800-814)MHz
Europe
Q3
(748-784)MHz
France, Australia
S5
(842-865)MHz
England
1518.750 801.100 749.100 855.275
2524.875 802.325 754.025 856.175
3525.625 805.050 756.000 857.625
4534.375 808.600 765.900 858.200
5536.875 810.550 772.000 863.075
6538.500 811.600 775.000 863.625
7551.000 813.300 778.775 864.425
8553.250 813.800 781.900 864.850
Channel A (P2R Only) Wired Mode (RF Disabled)