Shuttle SDD-470 User manual

Руководство по установке и эксплуатации
SDD-470
Мультимедийный проигрыватель
All manuals and user guides at all-guides.com
all-guides.com

CONTENTS
01
Specification....................................
Operation Check.................................
04
Alignment and adjustment..........................
06
Troubleshooting.................................
08
Printed Circuit Boards.............................
09
Wiring Diagram...................................
16
Electrical Parts List...............................
17
Exploded View...................................
23
Mechanical Parts List.............................
26
Schematic Diagrams..............................
29
Disassembly Instructions..........................
03
02
DVD DECK......................................
05
All manuals and user guides at all-guides.com

02
SPECIFICATION
General
Power Supply Requirements: DC 14.4V, Negative Ground
Maximum Output Power:
Chassis Dimensions: 178 x 163x 50mm (W x D x H)
DVD Deck Section
Discs Played:DVD, MPEG4,DIVX,VCD 1.0/2.0/3.0,MP3
WMA,CD,CD-R,CD-RW,Picture-CD
AUTO/PAL/NTSC
Video System:
FM Tuner Section
87.5 - 108MHz
IF
Usable Sensitivity(-20dB):
10.7MHz
15dB
28dB
522 - 1620K Hz
25W x 4(CH)
450KHz
Mounting Angle:
Video Section
Video System:
Video Output Level:
4:3 Letter Box, 4:3 Pan Scan,16:9
1.0V p-p 75 ohms
Audio Section
Maximium Output LEVEL:
Frequency Response:
Signal-to-noise Ratio:
Separation:
2Vrms (+ 3 dB)
20
20KHz
~
65dB
60dB
Tuning Range:
IF
Usable Sensitity (-30dB)
Signal-to-noise Ratio:
Stereo Separation:
Frequency Response:
60dB
30dB(1KHz)
30 15000 Hz
~
AM Tuner Section
Tuning Range:
Load Impedance:4 ohms
NOTE:Design and specifications are subject to change without notice for improvements.
All manuals and user guides at all-guides.com

DISASSEMBLY INSTRUCTIONS
1.Mounting Box: Slide out the mounting box in parallel.
2.Top cover: Release screw at the back of top cover, and pull
out the cover.
3.Bottom Cover: Turn over the unit to release the screws at the back
of bottom cover and one the top surface. Pull out the cover.
4.Disassemble the Panel:
Pull out the Front panel.
Release the left side and right side screws attached to with the base.
Pull the base out of the unit.
5.Disassemble the mechanism deck:
There are two screws to lock the mechanism deck at front ,Unscrew
both of them.
Remove the solder from fixed wires on the main, and remove the deck.
6.Disassemble the key board :
Release four screws .
Remove the back panel .
Then remove the key board.
7.Unscrew the left side bracket and the right side bracket. There are
two screw on each side.
8.Disassemble the main board :
9.Unscrew two screw at the leef bracket
remove the solder from the Tuner,and main board.
Uncrew two screw ar the ANT.Remove the solder from fixed wires.
Unscrew two crew at the Heatsink.
Remove the main board.
03
All manuals and user guides at all-guides.com

04
OPERATION CHECK
GENERAL SPECIFICATIONS OF SIGNAL
Standard frequency AM 1000 KHz (600, 1400 KHz)
FM 98.0 MHz (90.0, 106.0 MHz)
Signal output AM 74 dB/uV
FM 60 dB/uV
Modulation AM 1 kHz 30%
FM mono 1 KHz 22.5KHz
AF output level AM/FM
Power source voltage DC 14.4 V (backup voltage is the same as this )
AF load impedance 4 ohm pure resistance
Balance Mechanical center
Tone Mechanical center
The signal strength read in this section is voltage on the antenna.
Note : Use an RF generator for the AM band and a sweep
generator for the FM band.
All manuals and user guides at all-guides.com

05
DVD DECK
DVD DECK
All manuals and user guides at all-guides.com
all-guides.com

Equipment Required
FM IF/RF signal generator
Oscilloscope
Solid-state voltmeter (SSVM)
Frequency counter
Regulated DC power supply
DC digital voltmeter
Distortion meter
FM IF/RF ADJUSTMENT
FM IF and RF Alignment Using FM Signal Generator
Note : Press the radio power switch to turn on the radio. Signal
generator
output must be kept as low as possible to avoid overload
Setup Generator
Coupling
Generator Display
Setting
Indicator
Coupling
Adjust ment Remarks
IF FM RF
signal
generator
to ANT i/p
10.7 MHz
sweep
output
60 dB/uV
98.0
Mhz
Connect
oscillosc
ope
pin 3 &
ground
to Ic1
-
T1 Adjust so
that
maximum
AF output
power and
minimum
distortion.
RF
Low
High
Signal
generator
to
antenna
receptacle
90MHz Int 1
KHz 22.5KHz
mod. output
30dB/uV
106MHz Int
1 KHz 22.5
KHz mod.
output 30
dB/uV
90 MHz
106 MHz
SSVM
across
speaker
C3
L1
Adjust AF
output
power
for
maximum
06
ADJUSTMENT
and clipping.
All manuals and user guides at all-guides.com

07
ADJUSTMENT
Equipment Required
>AM/RF signal generator
>Oscilloscope
>Solid-state voltmeter (SSVM)
>Frequency counter
>Regulated DC power supply
>DC digital voltmeter
>Distortion meter
AM /RF ADJUSTMENT
AM/RF and RF Alignment Using AM Signal Generator
Note : Press the radio power switch to turn on the radio. Signal generator
output must be kept as low as possible to avoid overload and clipping.
Setup Generator
Coupling
Generator Display
Setting
Indicator
Coupling
Adjust ment Remarks
RF Signal
generator
to antenna
receptacle
600 KHz
Int 1 KHz
30% mod.
Output
74 dB/uV
600
Khz
SSVM
across
speaker
C1 Adjust
AF output
power for
maximum
RF
Cont.
Signal
generator
to
antenna
receptacle
1400 KHz
Int 1 KHz
30% mod.
74 dB/uV
1400
Mhz
SSVM
across
speaker
L3 Adjust AF
output
power
maximum
All manuals and user guides at all-guides.com

No Power
No Sound
Sound Skipping
The Operation Keys
Do Not Work
The Radio or
Automatic Selection
Does Not Work
The fuse is blown
Inserting the CD in reverse
direction
The CD is extremely dirty or
defected
Temperature inside the car is
too high
Condensation
Volume is at minimum
Wiring is not properly
connected
The installation angle is more
o
than 30
CD is extremely dirty or
Defected
The built-in microcomputer is
not operating properly due to
Interference
The antenna cable is not
connected correctly
The signals are too weak
Replace a new fuse
Remove the CD from the player
and insert the new one
Insert the CD with the label
facing up
Clean the CD or try to play
a new one
Cool off until the ambient
temperature return to normal
Leave the player off for an
hour or so and try again
Adjust volume to desired level
Check wiring connection
Adjust the installation angle to
o
less than 30
Clean the CD or try to play
a new one
Press the RESET button or
reinstall the front panel
properly
Connect the antenna cable
correctly
Select the station manually
A CD is already inside the
player slot
CD Cannot Be
Loaded or Ejected
The car ignition key not
been switched on
If the power supply is properly
connected to the car accessory
terminal, switch the ignition
key to ACC
Symptom Causes Solution
Before going through the check list, check wiring connection.
consult your nearest service dealer
08
TROUBLE SHOOTING
If any of the problems persist after checklist has been made,
All manuals and user guides at all-guides.com

09
PRINTED CIRCUIT BOARDS
MAIN BOARD ( LAYOUT )
All manuals and user guides at all-guides.com

10
PRINTED CIRCUIT BOARDS
All manuals and user guides at all-guides.com
all-guides.com

11
PRINTED CIRCUIT BOARDS
All manuals and user guides at all-guides.com

12
PRINTED CIRCUIT BOARDS
ey-opp -Bottom
KCer
ey- ilkscreen-tom
KSbot
All manuals and user guides at all-guides.com

13
PRINTED CIRCUIT BOARDS
ey-opp-T
KCerop
ey-lkscren-
KSi eTop
All manuals and user guides at all-guides.com

14
PRINTED CIRCUIT BOARDS
SERVO BOARD
All manuals and user guides at all-guides.com

15
PRINTED CIRCUIT BOARDS
SERVO BOARD
All manuals and user guides at all-guides.com
all-guides.com

WIRING DIAGRAM
16
Синий
Черный
Красный
Желтый
Зеленый
Зеленый/Черный
Белый
Белый/Черный
Серый
Серый/Черный
Фиолетовый
Фиолетовый/Черный
Замок зажигания
Тыловая
правая АС
Тыловая
левая АС
Фронтальная
правая АС
Фронтальная
левая АС
Провод управления
антенной, усилителем и т.д.
Кузов автомобиля
Радио антенна
4%х канальный
усилитель
усилитель
Выход на сабвуфер
Видео выход
Линейный аудио выход
Линейный аудио выход
Монитор
DVD проигрыватель
Аккумуляторная
батарея 12В
Коаксиальный выход
Красный
Желтый
1А
15А
Если после отключения питания
устройство сбрасывает настройки,
откройте держатели предохранителей и
переставьте местами красный и
желтый провода питания
К коннектору
К ISO коннектору
Желтый Желтый
Красный Красный
Желтый
Красный
Желтый
Красный
15А
1А
15А
1А
All manuals and user guides at all-guides.com

06-106168-0002-0D-N 一体化主板6168D(4*2 5）SPHE8202TQ
（4730IC+SUB+ISO）6系 列 (俄罗斯)
06-206168-0 001 SD卡板，PY-6168D，SD PCB，132.1*142.5*1.2MM/16PCS
双面板
17-010303-1 101 L ED灯 3Φ 红发红 普 亮（主机） 主机用
17-030303-0 101 插 件LED灯(蓝色)3.0mm
19-010091-1 001 S D卡座 SDBMF-009XXB OXZ
21-014250-0 071 S W输出线 单条250MM 一头公端子一头剥线(绿色)
21-200300-0 059 输 出线video output line (灰 色)
21-306250-1 010 RCA输出线 2 50MM(棕色)
21-306250-1 011 RCA输出线 2 50MM （灰色）
29-713002-1 309 F FC排线FFC 13P A SIDE L=13 0mm 1 .0mm
33-040340-0 001 天线插 座 ANT
34-010114-0 702 14P输出线 公插带2个保险丝（一个1A，一个15A)(ISO
插)
06-106168-0002-1D-N 一体化主 板6168D(4*25）SPHE 820 2TQ
（4730IC+SUB+ISO）6系 列 外发 (俄罗斯)
04-011052-0 100 插 件晶体 11.0592MHz 30P PM S型
04-027001-0 100 插 件晶体 27.000MHz 30PP M S型 30 PPM S型
06-106168-0 002 P Y-6168D-MB 186.7 *15 0.5*1.2MM/1pcs 双 面板
07-060000-0 940 贴 片排阻 0R 5% 0603
07-080000-9 900 贴 片电阻 0 5% 0603
07-080100-0 800 贴 片电阻 SMD 10R 1206 5%
07-080100-9 900 贴 片电阻 10 5% 0603
07-080101-9 900 贴 片电阻 100 5% 0603
07-080102-0 800 贴 片电阻 SMD 1K 1206 1/4W 5%
07-080102-9 900 贴 片电阻 1K 5% 0603
07-080103-9 900 贴 片电阻 10K 5% 0603
07-080103-9 940 贴 片排阻 10K 5% 0603
07-080104-9 900 贴 片电阻 100K 5% 0603
07-080108-9 900 贴 片电阻 1R 5% 0603
07-080123-9 900 贴 片电阻 12K 5% 0603
07-080151-9 900 贴 片电阻 150 5% 0603
07-080151-0 800 贴 片电阻 SMD 150R 1206 1/4W 5%
07-080153-9 900 贴 片电阻 15K 5% 0603
07-080182-9 900 贴 片电阻 1K8 5% 0603
07-080201-9 900 贴 片电阻 200 5% 0603
07-080203-9 900 贴 片电阻 20K 5% 0603
07-080220-0 800 贴 片电阻 SMD 22R 1206 1/4W 5%
17
All manuals and user guides at all-guides.com

07-080220-9900 贴片电阻 22 5% 0603
07-080221-9900 贴片电阻 220 5% 0603
07-080222-9900 贴片电阻 2K2 5% 0603
07-080223-9900 贴片电阻 22K 5% 0603
07-080228-0800 贴片电阻 2R2 5% 1206 1/4W
07-080228-9900 贴片电阻 2R2 5% 0603
07-080303-9900 贴片电阻 30K 5% 0603
07-080330-9900 贴片电阻 33 5% 0603
07-080330-9940 贴片排阻 33 5% 0603
07-080332-9900 贴片电阻 3K3 5% 0603
07-080361-9900 贴片电阻 360 5% 0603
07-080470-0800 贴片电阻 SMD 47R 1206 1/4W 5%
07-080470-9900 贴片电阻 47 5% 0603
07-080471-9900 贴片电阻 470 5% 0603
07-080472-9900 贴片电阻 4K7 5% 0603
07-080473-9900 贴片电阻 47K 5% 0603
07-080518-9900 贴片电阻 5R1 5% 0603
07-080562-9900 贴片电阻 5K6 5% 0603
07-080680-9900 贴片电阻 68 5% 0603
07-080683-9900 贴片电阻 68K 5% 0603
07-080684-9900 贴片电阻 680K 5% 0603
07-080750-9900 贴片电阻 75 5% 0603
07-080821-0800 贴片电阻 820 5% 1206 1/4W
07-080822-9900 贴片电阻 8K2 5% 0603
07-113060-0101 热敏电阻 300mA 60V T60-030
08-210222-1029 电解电容 16V 2200UF ±20% 10*2 0
08-216100-2 022 电解电容 10uF/25V ±20％ φ4X5mm 排带2.5MM脚距，
平底部伸出
08-216101-0 029 电解电容 100UF/10V ±20% φ5X5mm 排带2.5MM脚距，
平底部伸出
08-216101-1 029 电解电容 100UF/16V ±20% φ6.3X5mm 排带2.5MM脚
距，平底部伸出
08-216221-0 029 电解电容 220UF/10V ±20% φ6.3*5mm 排带2.5MM脚
距，平底部伸出
08-216470-1 029 电解电容 47UF/16V ±20% φ5X5mm 排带2.5MM脚距，
平底部伸出
08-216478-5 022 电解电容 4.7UF/50V ±20% φ4X5mm 排带2.5MM脚距，
平底部伸出
09-088100-1300 贴片电容 10P/50V 0603 ±5％
09-088101-1300 贴片电容 100P/50V 0603 ±5％
09-088102-1300 贴片电容 102/50V 0603 ±10%
18
All manuals and user guides at all-guides.com

09-088103-1 300 贴 片电容 103/50V 0603 ±10％
09-088104-1 300 贴 片电容 104/25V 0603 ±10％
09-088105-1 300 贴 片电容 105/16V 0603 ±10％
09-088152-1 300 贴 片电容 152/50V 0603 ±10％
09-088153-1 300 贴 片电容 153/50V 0603 ±10％
09-088200-1 300 贴 片电容 20P/50V 0603 ±5％
09-088221-1 300 贴 片电容 220P/50V 0603 ±5％
09-088224-1 300 贴 片电容 224/25V 0603 ±10％
09-088272-1 300 贴 片电容 272/50V 0603 ±10％
09-088330-1 300 贴 片电容 33P/50V 0603 ±5％
09-088471-1 300 贴 片电容 470P/50V 0603 ±5％
09-088821-1 300 贴 片电容 820P/50V 0603 ±5％
10-021132-1 280 贴 片三极管 SOT-89,2SB1 132
10-063904-0 170 贴 片三极管 SOT-23,2NS3 904
10-080436-0 201 插 件三极管 2SB436 ( 塑封)
10-090435-0 201 插 件三极管 2SD435 TO-251 4 0V，3A，10W( 塑封)
10-178050-7 130 插 件三极管 TO-92,S8050
10-178050-7 170 贴 片三极管 SOT-23,C805 0
10-178550-7 170 贴 片三极管 SOT-23,C855 0
10-179014-7 170 贴 片三极管KTC9014S-P TK/P， SOT-23
10-179015-7 170 贴 片三极管 SOT-23,9015
11-004016-0 201 集 成电路 IC SSOP-54 SAMSUN G UC60 4X16M
11-007313-0 401 四声道输出数字音频控 制处理IC 7313
11-020431-0 700 I C TO-92,TL431
11-025T80-0 400 I C 8M FLASH (SPI EN25T8 0) SO-8
11-037388-0 600 I C TDA7388
11-047805-0 600 三 端稳压 IC L7805 TO-220
11-092244-0 400 I C SOP-8,NJM2244
11-102402-0 400 I C SOP-8,24C02N
11-196287-9 400 I C SOP-8,BA6287F
11-321117-0 900 I C LD1117 (3.3V) TO-2 23
11-331410-0 400 I C SOP-8,MP1410
11-411718-0 000 I C TO-223,LD1117( 1.8V)
11-464558-0 400 I C KIA4558F
11-478L05-0 600 集 成电路 TO-92 NJM78L05
11-506608-4 003 集 成电路 LJ6608-TQ+OIR T(4730数字IC)
11-AM5888-0 100 I C AM5888S DIP28-SS OPH
11-HE8202-0 500 I C SPHE8202TQ QFP12 8
12-114001-0 000 普 通二极管 IN4001
12-115401-0 000 普 通二极管 IN5401
12-115819-0 120 插 件二极管 IN5819
12-214148-0 011 贴 片二极管 IN4148 1206 圆柱形
12-300051-0 021 贴 片稳压二极管 5.1V (4.95V~ 5.15V)1206
12-300056-0 021 贴 片二极管 SMD 5V6 （5.5V-5. 7V )1206 圆柱形
19
All manuals and user guides at all-guides.com