Shuttle Kiosk K15 Series User manual
Kiosk K15 Series
Quick Start Guide
Copyright © 2021, Shuttle Corporation. All Rights Reserved
Package Contents
For safety reasons, please ensure that the power cord is disconnected before opening the
case. Do not attempt to open the system unless by authorized qualified personnel.
, , ,
!
1. Insert the key into the lockhole at the rear case and turn it clockwise to open the front panel.
1. Power switch
2. Rear case
3. Connector for wifi antennas
4. Cable hole
5. Thermal vent
11. Speakers
12. IC card reader
13. Barcode scanner
14. NFC RFID reader
15. Counter mount (optional)
6. Webcam
7. 15” Touch display
8. Release button
9. Receipt printer
10. Front panel’s lockhole
2. Close the front panel in reverse order avnd remove the key.
Front panel
ad
b
c
Unlock
Lockhole
Rear case
Clockwise
a
Lockhole
Front panel
b c
Lock
Counter-
clockwise
d
Do not touch the print head thermal elements. The print head becomes very hot just after
printing and is very dangerous. Be sure to allow the print head to cool down (after printing)
before cleaning it. Also, be sure to turn off the rinter power before cleaning the print head.
!
1. As shown, use the key to push the release button to open the printer cover.
2. Remove the used paper roll from the paper tray and load the new paper roll.
Make sure that a few inches of the paper is extended over the cover edge.
3. Close the printer cover. Tear the excess paper across the tear bar.
The product’s colour and specifications may vary from the actually shipping product.
Should any accessories be required, please contact Shuttle or your relevant supplier.
i
Kiosk K15WL01 / K15RK01 (x1)
Wi-Fi Antenna (x1) Wi-Fi (x1)
Roll Paper Partition (x1)
(x1)
Magnetic Keychain (x1)
(x1)
The key to the case rear door. (x2)
The key to the printer cover. (x3)
58mm thermal paper partition installation.
Paper roll width 80mm / 58mm selectable.
58mm paper roll only
Make sure the paper roll
is loaded in the direction.
Release button
b
a
SCAN
SCAN
cd
Cut the paper neatly.
e
SCAN
2
3
4
5
7
6
8
9
10
11
12
13
14
11
5
1
15
Incorrectly replacing the battery may damage this computer. Replace only with the same or equivalent as recommended by Shuttle. Dispose of used batteries according to the manufacturer’s instructions.
Shuttle,
!
The unit can be operated at an ambient temperature of max. 35°C (95°F).
Do not expose it to temperature below 5°C (41°F) or above 35°C (95°F).
35°C (95°F)
5°C (41°F) 35°C (95°F)
1. ():
2. (): (1) 3010
(2) 2, 1
Take the antennas out of the accessory box. Screw the included antennas on the appropriate
connector at the rear case. Make sure it is aligned vertically or horizontally to achieve the best
possible signal reception.
1. Connect the power cable to a wall outlet.
2. Place the magnetic keychain against the power switch for 1 seconds and remove it,
then the power status LED will start to blink for 2 seconds and turn on the system.
Repeat the steps above to turn off the system.
2. As shown, install the two handles on the both sides of rear case and secure with the four
screws.
3. Gently push the four rubber cover into the four screw holes until it properly sits in place.
- Arrange the wires and cables connected to the product to prevent tripping, pulling or entanglement.
- Make sure the product does not hang over the edge of the supporting furniture.
- Do not place the product on supporting furniture higher than 1 meter.
1
Connector for wifi antennas
Wifi
2
Counter Mount 100 x 100 mm
Screws 6M x 12L * 4pcs
6M x 12L * 4
1. As shown, install the counter mount and secure with the four screws.
1
1
AC 100-240 V, 50-60 Hz, 1.5 A max
2
VESA mounting to the wall (optional)
The standard VESA openings show where
an arm / wall mount kit which is available
separately can be attached.
VESA ,
VESA / VESA
3
2
Screws 6M x 12L * 4pcs
6M x 12L * 4
The touch of your finger replaces the input devices and is all you need to operate the K15 series.
K15 series ,
Cleaning the screen: Turn off the system and disconnect all cables. Use a cleaning cloth
which is soft, lint-free and a little damp to gently wipe the screen surface. Do not spray
liquids directly onto the device.
:
!
The K15 series can be wall-mounted using a VESA compatible 100 mm x 100 mm wall / arm
K15 series VESA 100 mm x 100 mm /
25 kg,
Le Série K15 peut être fixé au mur ou à un bras à l'aide d'un support VESA 100x100 mm.
Le support doit être conçu pour une charge d'au moins 25 kg et ne doit pas être situé à plus
de 2 m de hauteur.
!
This manual suits for next models
2
Other Shuttle Monitor manuals
