SI-lIte SRTBP09RGB User manual

SRTBP09RGB Touch Controller
User
User
User
User Manual
Manual
Manual
Manual
Please read this manual carefully before using this controller.

�
�
�
�Instructions
Instructions
Instructions
Instructions
�
�
�
�After-salesservice
�
�
�
�
SRTBP09RGB
Thank you for purchasing the SRTBP09RGB LED Strip kit with “Touch” Control. Please
read this manual prior to installation to avoid unnecessary damage to the LED strip,
power supply or controller.
Firstly, please check you have all required kit parts:
5M REEL RGB LED STRIP
RF CONTROLLER WITH SIGNAL LEAD & CONNECTOR TO LED STRIP
POWER SUPPLY UNIT
TOUCH CONTROLLER & WALL MOUNTING UNIT
Warranty of this product is 2 years from date of purchase from SI LITE. During this
period we guarantee to repair or replace any part of this kit that ceases to work
subject to the product being installed and used in accordance with these instructions.
For more information please refer to the Product Warranty Information panel in our
latest catalogue, or go to www.si-lite.com/legal
This warranty will not apply in the case of:
1. Damage caused by misuse or use not in accordance with these instructions
2. Damage caused by unauthorised removal, repair or modication of any part of
this kit.
3. Damage caused by transportation, shock, or improper storage after purchase.
4. Damage caused by abnormal voltage, re, ood, earthquake or other natural
disasters.
5. Negligence or improper maintenance, including storage at high temperatures
or in humid environments, or in the vicinity of hazardous chemical substances.
Proof of date of purchase will be required for all warranty claims. SI LITE bears no
responsibility for any costs associated with the replacement of faulty products.
Safety Instructions
1. For installation, avoid humid areas, excessive heat (above 85 degrees C), strong
magnetic elds, or high pressure areas.
2. Ensure that all cables are connected correctly and securely in order to avoid
short-circuit or re hazard.
3. Install the RF Controller in a well-ventilated position to ensure a moderate
ambient temperature is maintained.
4. Before using this product please check the DC power and voltage meets the
product’s technical requirements.
5. Check the product is coorectly wired before turning on power supply.
6. If the product is not working correctly, do not make unauthorised repairs.
Contact your stockist.

Introduction
1. Technology parameters;
Type SRTBP09RGB
Supply voltage
Max. load current
DC12V-24V
3A*3CH
Output signal
Control mode
Attended mode
Three-way signal
Touch Control
Total male connector
Positive connect
Controller size L100×W50× H28(mm)
Remote size L120×W65×18(mm)
The SRTBP09RGB is a “Touch Control” LED colour-changing kit, which can providea xed colour
of choice using the “Touch” remote control unit. Fixed red, green, blue or white colours can be
selected by pressing the appropriate R, G ,B or W buttons. Specic colours from the spectrum
can be selected by pressing or stroking the required area of the colour wheel.
Brightness can be adjusted by pressing or stroking the brightness bar.
Up to 3 favourite colours can be stored in the memory buttons (M1, M2, M3).
2. Functions
1. Select chosen colour from R, G, B or W buttons or from an area of the colour wheel.
2. To place a chosen colour into one of the three DIY memories, select chosen colour then
press and hold the chosen memory button until the LEDs ash. Your memory colour is now
stored.
3. The brightness bar has 255 in-built levels.
4. Brightness can also be adjusted by pressing the brightness button on the RF Controller.

2 Remote Control Outside drawing: (Figure 2)
3. Structure
(1).outside drawing of master controller: (Figure 1)

4 Remote Control Mode Description (Figure 4)
Colour wheel:thecorresponding colour will appear if you touch it
Brightness adjustment: You can change the brightness if you touch it.
The left part is the minimum brightness; the right part is brightest part.
Switch : You can turn on and turn off by touching.
。
Static red Static green Static blue
Static white Mode memory key.
3Schematic diagram of the controller connection: (Figure 3)

2. RF Ccontroller buttons description
:
Brightness adjustment button: you can change the brightness if you touch it.
A continuous change willappear if you touch it continuously.
Switch button: On/Off
The product can be turned on/o via the RF Contoller or the Touch remote control.
CONNECTION PROCESS
1. It is recommended that you connect and test this product prior to installation, to ensure
the product is fully working.
2. Connect the LED strip reel to the RF Controller - place the 4-pin connector itno the
socket at the end of the cable that comes from the On/O switch side of the RF Controller.
Ensure that the LEDs are on the same side as the arrow on the 4-pin socket. The underside of
the LED strip must be on the same side as the letters +GRB.
3. Connect the RF Controller power cable to the output cable of the power supply.
4.
5.
To extend the ribbon tape cut at selected cut point and use the 100mm extension
cables provided. Place the plastic connector over the copper PCB, t locking plate and
squeeze together gently using a pair of pliers.
Once all connections are secure you may now connect to the mains power supply.