SIBOASI SS-B-8000 Installer manual

1
Catalogue
Introduction………………………………………………………………………2
Attention……………………………………………………………………………2
Functions…………………………………………………………………………...4
Parts…………………………………………………………………………………..5
Main machine…………………………………………………………………………...5
Remote control………………………………………………………………………….5
Installment Instruction……………………………………………………….6
Packing list………………………………………………………………………………6
Assembling………………………………………………………………………………6
Use Instruction………………………………………………………………….9
Remote control mode………………………………………………………………….9
Maintenance……………………………………………………………………..17
Normal phenomenon…………………………………………………………………..17
Trouble examination…………………………………………………………………..18
Maintenance……………………………………………………………………………18
Service guide…………………………………………………………………….19
After-sales service center………………………………………………………………19
Service notice………………………………………………………………………….19
Warranty card………………………………………………………………………….20
Maintain record………………………………………………………………………..21

2
Introduction
Dear customer:
Thanks for using SIBOASI series products.
Please read this manual carefully before using the machine.
Only when you are familiar with the machine and you understand the correct usage can you use
the machine on the squash court. avoid misoperation which could result in damaging the squash
ball machine or other accidents.
Attention:
Because the machines are regularly improved, in the manual some changes are
explained. Sometimes the latest changes are not mentioned in the manual, we apologize
that there is no notice for these changes then.
Warning▲
Do not allow the minors to play with the machine.
Do not stand in front of the machine during working status to prevent people from getting
hurt.
Attention:
Please observe the following items strictly.
Warning signal▲
The next items of the manual with warning signal should be abided strictly, otherwise
there will be danger of the personal safety or could lead to a significant accident.
Forbidding signal●
The next items of the manual with forbidden signal should be abided strictly, otherwise
there will be danger of the personal safety or could lead to damage of the machine.
▲Do not disassemble or change the machine voluntarily.
▲Do not break or move the power equipment of the machine
▲Do not let the children or the minors play with the machine or power equipment.
▲Do not control the power or machine switch with barefoot or wet hands.

3
▲Do not use the machine in the rainy and stormy weather.
▲Do not use the machine close to volatile or flammable gas.
▲This machine sets the time delay function: 5 seconds after starting the machine can serve
ball automatically, any time do not stretch out your face in front of the ball window to look
at, otherwise it can result in a personal accident.
▲Do not touch the inner parts of the machine during working .
▲If the machine has an unusual situation, for example: big noise, strong smog and leakage,
please immediately cut the power, then contact with local service provider or
manufacturer.
▲When cleaning up interior of the machine, do not let the minors operate the machine, in
order to avoid damaging the machine or causing any danger.
●No moving during working.
●No operating when the state of the battery is insufficient when in the direct-current power
supply condition.
●Don’t put other objects than squash balls onto or into the squash ball machine.
●No laying aside in moist or other bad environment.
●No cleaning the surface of the machine with volatile wet cloth.
Warning▲
SIBOASI products are the professional sports-goods equipment. We are not responsible
for any legal responsibility if any other people change the products for other purpose and
cause damage.

4
Functions
B-8
Hand-making Full-function First-design Pretty fashion
Different combinations of ball speed、fixed、flat stroke、horizontal displacement、
vertical displacement、 topspin、backspin、two lines function。Every program can be
changed automatically (30 seconds/program).The ball speed can be fully random
adjusted,which makes the machine more human oriented.
There are 16 kinds programs in the random mode and every program can change
automatically every 30 minutes .
·Remote control (LCD display).
·Double power, AC, DC available.
·Reset and pause function.
·Remote control: ball speed, feed frequency ,work/pause, fixed point/flat stroke,
horizontal swing,horizontal displacement、vertical displacement 、
topspin、backspin、two lines function
·Ball speed range: 30-150 km / h,
·Ball Capacity: 20
·frequency range : 2-12 seconds.
·Ball direction control: built-in.
·Battery working hour: 20 – 40 minutes
·Colour:red,silver
·Suitable for: Junior player to senior player.
◆Weight：25KG
◆Size：.main machine: 48*39*61(cm)
▲Warning
Do not allow minors to play with the machine.Do not stand in front of the machine during
working status to prevent people from getting hurt.

5
Parts
Main machine：
Retractable
Insurance Block
Power
Interface
Remote control：
Vertical
Stock
Horizontal
speed
(K/H)
speed
Horizontal
Lob ball
Vertical
Random
00
(Second)
frequency
Narrow
Among
Wide
Back spin
Top spin
W/A/N
Vertical
ON/OFF
Pattern
Horizontal
frequency
frequency
speed
Reset
00 0
Vertical downward
Speed down
Speed up
Reset
Point/function stock
On/Off
Wide/Middle/Narrow/Horizontal
Vertical upward
Horizontal left movement
Self-program/Random
Horizontal right movement
Frequency down
Frequency up
Power switch
LCD Display
Topspin
Backspin

6
Accessory:charger, power cable
Installment Instruction
一、 Packing list
Description Quantity Description Quantity
Main machine parts one Charger one
Ac power cable one Remote control one
Fuse pipe one Manual one
二、 Assembling
Note: When demolishing the machine packing module, it can possibly see the squash surface
down on the packing protective film and the machine , this is the normal phenomenon
leaving on the product ex-factory after testing examination.
1.The wheels of the main machine
12
install the wheel according to the direction of arrow
twist the nut
twist the nut with the 12-14 open-mouth wrench
twist the nut
2.Fuse pipe

7
OFF DC
AC
Fuse pipe

Panel control
Revolving the fuse pipe cover, assemble the fuse pipe and revolve it tightly.
3.Charging
AC socket
OFF DC
AC
DC lamp
Battery
Level
protector
Top spin
Narrow
Among
Vertical
ON/OFF
Random Back spin
Horizontal Wide
frequency frequency
speed speed
Reset
(3-Line)
Narrow
Among
Wide
Back spin
Top spin
(Second)
frequency
(K/H)
speed
Horizontal
Lob ball
Vertical
Random
Charger
AC power
Please match the
convex and concave
parts and plug firmly.
DC socket DC socket
Convex partConcave part DC power socket
Panel
control
Pull-rod Main machine
Protection
circle
1) Take out the DC power cable(the two ends can be exchangable).
2) Identify the DC power cable end indentation(concave) part and consistent with the DC socket
bulge(convex) part of the main machine, insert and lock tightly the knob. And with the same
method, make the connection of the DC power and the portable battery.
Note:The connection of the DC power cable , the battery and the main machine must
confirm the correct direction, otherwise this will cause the power short circuit to burn out
the machine or have an accident.
Attention:The battery was charged before shipment,please use it out before
charging.
When the battery LED display on the panel control show 2 or 3 lights,and the ball
has no power then charge the battery for 4-6 hours.
When the red light of the charger was off,please pull out power socket.If not,it may
damage the battery.
4. Battery of the remote control
1) Used with the 9V dry battery.

8
2) Softly press and take out the battery cover..
3) Make the alignment of the“+”“-” of the battery and the“+”“-”of the remote control, incline
slightly the battery and put into the battery with the finger.
4) Covers the battery cover according to the reversed direction order.
5) Turns on the remote control switch, LCD have the display.
2
1
softly press and take out
the battery cover incline slightly the battery
and match the "+""-"
Note: When installing or replacing the battery, please carefully examine “+” “-”
polarity, cannot connect reversely, otherwise it will be possible to damage the
remote control.
Warning▲
Do not allow minors to play with the machine.Do not stand in front of the
machine during working status to prevent people from getting hurt.

9
Use Instruction
◆Choose the power
AC DC
OFF
AC socket DC socket DC socket
AC DC
OFF
AC DC
OFF OFF DC
AC
OFF DC
AC
DC socket DC socket
AC socket
1．Choose the switch position“II”, ie, choose the “AC” power.then the power indication light
will be on, the ball speed of LCD display is“00”and the frequency is “0” .
2．Choose the switch position“I”,ie,choose the “DC” power.then the power indication light will
be on, the ball speed of LCD display is“00”and the frequency is “0” .
3．Choose the switch position“0”,ie,turn off the power.then the power indication light will be off.
◆Turn on the remote control switch
remote
control
power
switch
1. Make sure well-assembling the battery.
2. Turn on the remote control switch.
1. Start the machine

10
AC DC
OFF
/
ON /OFF
AC soc ket
D C lam p
D C so cket
SS V 8-8
pr otec tor
(Se con d)
freq uen cy
(K/H)
spe ed
AC DC
OFF
三、Select “AC” or “DC” power.
四、 Softly touch the “ON/OFF” button, then will a sound ”di”，the main engine begins to
work,and the ball speed of the LCD display is 120 km/hr(set by factory)。The machine begin
to serving ball after 5 seconds,the frequency of serving show 8 seconds/ball (set by factory).
Note: ●“Reset” is the clear button, when softly touch this button, it will clear all the
program settings except the self-programming mode.
● When starting the machine, the power light and the electric quantity light
will twinkle, which is the normal phenomenon, for the instantaneous
pressure is big at first.
●The machine will serve ball automatically after 5 seconds when you touch
the"ON / OF" button
2. Adjust the ball speed
ON /O FF speed
OFF DC
AC
spe ed
(K/H)
fre quenc y
(Se con d)
pro te ctor
SSV8-8
D C so cket
D C lam p
AC soc ke t

11
1．Softly touch the “ON/OFF” button and start the machine.
2．Softly touch the button “speed△Up” “speed▽Down”, then adjust the ball speed in the range
of 30 to 150 km/hr .
3．Softly touch again the “ON/OFF” or “Reset” button, the machine stop working.
3. Adjust the ball frequency
OFF DC
AC
speed
(K/H)
frequency
(Second)
protector
SSV8-8
DC socket
DC lamp
AC socket
frequency
ON/OFF
◆Touch softly the “ON/OFF” button and start the machine.
◆Touch softly the button “frequency△Up” “frequency▽Down”, then adjust the ball frequency
in the range of 2 to 12 sec/ball.
◆Touch softly again the “ON/OFF” or “Reset” button, the machine stop working.
4. Set the position for horizontal serving ball

12
ON/OFF Horizontal Vertical
8
Horizontal
speed
(K/H)
frequency
(Second)
Top spin
Back spin
Wide
Among
Narrow
120
120
Random
AC socket
DC lamp
DC socket
SSV8-8
protector
AC DC
OFF
a) Touch softly the “ON/OFF” button and start the machine.Touch ‘Horizontal’ ◤(Left)
the 1st time,horizontal serving ball in the middle place(set by itself) swing to left at an
angle (4°-8°),see the above picture from C to B ; Touch ‘Horizontal’ ◤(Left) the 2nd
time,the position of horizontal serving ball swing to left at an angle (4°-8°) again,see
the above picture from B to A ;
Then touch ‘Horizontal’ ◥(Right) the 3th time,the position of horizontal serving ball
will return back and swing to right at an angle (4°-8°), see the above picture from A to
B.
b) Touch repeatly ‘Horizontal’ ◥, horizontal serving ball with the same position one by
one from B to C,from C to D, from D to E .
3. This operating repeatly can control the angle of horizontal serving ball .
4. Touch softly again the “ON/OFF” or “Reset” button, the machine stop working.
5. Set horizontal swing

13
O F F D C
AC
p ro tec to r
SSV8-8
D C s oc k e t
D C l a m p
A C so ck et
Ra n d o m
12 0
12 0
Na rr ow
Am o n g
W ide
B ack sp in
To p s pin
(Second)
fr equ en cy
( K/ H)
sp e ed
H ori zon tal 8
Ve rt ic al
/O F F
O N W /A /N
1. Touch softly the “ON/OFF” button and start the machine.
2. Touch softly the “W/A/N” button the fourth time,to set horizontal swing ball,at the same time
the horizontal show led are on in the LCD.
3. Touch softly again the “ON/OFF” or “Reset” button, the machine stop working.
Note：Touch softly the “W/A/N” button，the 1st time to set Wide-line.
Touch softly the “W/A/N” button，the 2nd time to set Among-line.
Touch softly the “W/A/N” button，the 3rd time to set Narrow-line.
Touch softly the “W/A/N” button，the 4th time to set horizontal swing.
Touch softly the “W/A/N” button，the 5th time cancel all functions.
6. Set the position for vertical serving ball

14
ON/OFF Vertical Vert ical
8
Horizontal
speed
(K/H)
frequency
(Second)
Top spin
Back spin
Wide
Among
Narrow
120
120
Random
AC socket
DC lamp
DC socket
SSV8-8
protector
AC DC
OFF
a) Touch softly the “ON/OFF” button and start the machine.
b) Touch ‘Vertical’ ▲(Up) button the 1st time,serving ball in the position of flat
stroking upward swing at an angle (5°-10°),see the above picture from A to B; touch
‘Vertical’ ▲(Up) button the 2nd time, the position of vertical serving upward swing
at an angle (5°-10°) again,see the above picture from B to C; touch ‘Vertical’ ▲(Up)
button the 3rd
time, the position of vertical serving upward swing at an angle (5°-10°) again,see
the above picture from C to D.
c) Touch ‘Vertical’ ▼ (Down) button the 1st time,serving ball from the highest
position downward swing at an angle (5°-10°),see the above picture from D to C;
touch ‘Vertical’ ▼ (Down) button the 2nd time, the position of vertical serving
downward swing at an angle (5°-10°) again,see the above picture from C to B;
touch ‘Vertical’ ▼ (Down) button the 3rd time, the position of vertical serving
downward swing at an angle (5°-10°) again,see the above picture from B to A.
d) This operating repeatly can control the angle of serving ball .
e) Touch softly again the “ON/OFF” or “Reset” button, the machine stop working.
7. Choose the top spin ball shooting
O F F DC
AC
p rot ecto r
SSV8-8
D C s ock et
D C l am p
A C soc ket
Ra nd o m
120
150
Nar ro w
Am o ng
Wid e
Ba ck s pin
Top sp in
(Second)
fre que ncy
(K /H )
sp ee d
Ho rizo nta l 8
Ve rti ca l
/O F F
O N Top spin

15
1．Touch softly the “ON/OFF” button and start the machine.
2．Touch softly “top spin” button the 1st time, set the top spin ball shooting.（speed of the up
wheel is 130km/h ，speed of the down wheel is 80km/h ）， touch ‘top spin’ button
again ,increase the power of top spin（speed of the up wheel is 140km/h，speed of the down
wheel is 80km/h），touch softly “top spin” button the 3rd time,top spin serving mode will be
cancelled.
3．Touch softly again the “ON/OFF” or “Reset” button, the machine stop working.
8. Choose the back spin ball shooting
OFF DC
AC
p ro tector
SS V 8-8
D C s oc ket
D C la mp
AC so ck et
Ba ck
sp in
(Second)
freq uen cy
(K /H)
sp eed
/O FF
ON Back spin
1.Touch softly the “ON/OFF” button and start the machine.
2. Touch softly “back spin” button the 1st time, set the back spin ball shooting.（speed of the up
wheel is 120km/h，speed of the down wheel is 150km/h），touch ‘back spin’ button again ,increase
the power of back spin（speed of the up wheel is 110km/h，speed of the down wheel is 150km/h），
touch softly “back spin” button the 3rd time,back spin serving mode will be cancelled.
3. Touch softly again the “ON/OFF” or “Reset” button, the machine stop working.
Warning▲
Do not allow minors to play with the machine.Do not stand in front of the
machine during working status to prevent people from getting hurt.

16
9. Choose the lob ball shooting
/OFF
ON
OFF DC
AC
protector
SSV8-8
DC socket
DC lamp
AC socket
Random
120
120
Narrow
Among
Wide
Back spin
Top spin
(Second)
frequency
(K/H)
speed
Horizontal 8
Vertical
Vertical
1. Touch softly the “ON/OFF” button and start the machine.
2. Touch softly “Vertical” ▲(Up) button the 3rd time, set lob ball shooting.
3. Touch softly again the “ON/OFF” or “Reset” button, the machine stop working.
◆Choose the forehand or backhand Narrow-line ball shooting
/O F F
O N
O F F D C
A C
sp ee d
(K/H)
fre que ncy
(Se co nd )
p rot ecto r
SS V 8 - 8
D C s ock et
D C l am p
A C s oc ket
Na rr ow
W /A /N
1. Touch softly the “ON/OFF” button and start the machine.
2. Touch softly the ‘W/A/N’ button the 3rd time to set forehand or backhand narrow-line
ball shooting.
3. Touch softly again the “ON/OFF” or “Reset” button, the machine stop working.
Note: The distance of the narrow-line is 2 to 3 meters, It is convenient for trainers by
single or two persons to run-training forehand and backhand by small step at the same
time.

17
◆Choose the forehand or backhand Middle-line ball shooting
/O F F
O N W /A /N
O F F D C
AC
sp ee d
( K/H )
fre qu enc y
(Se co nd )
p rot ect or
SSV8- 8
D C soc ket
D C lam p
A C s ock et
W ide
1. Touch softly the “ON/OFF” button and start the machine.
2. Touch softly the ‘W/A/N’ button the 2st time to set forehand or backhand Middle-line
ball shooting.
3. Touch softly again the “ON/OFF” or “Reset” button, the machine stop working.
Note: the distance of the wide-line is 3 to 4 meters, It is convenient for trainers by
single or two persons to run-training forehand and backhand by big step at the same
time
◆Choose the forehand or backhand Wide-line ball shooting
/O F F
O N W /A /N
O F F D C
AC
sp e e d
( K/ H)
fr equ en cy
(S e c o n d )
p ro tec to r
S S V 8 - 8
D C so ck et
D C la mp
A C soc ke t
W id e
1. Touch softly the “ON/OFF” button and start the machine.
2. Touch softly the ‘W/A/N’ button the 1st time to set forehand or backhand Wide-line
ball shooting.

18
3. Touch softly again the “ON/OFF” or “Reset” button, the machine stop working.
Note: the distance of the wide-line is 4 to 5 meters, It is convenient for trainers by
single or two persons to run-training forehand and backhand by super-big step at the
same time
10. Self-programming（Set）
P a tte rn
O F F
D C
A C
s to c k /O F F
O N
H o riz o n ta l
V ertic a l
/
The machine could shoot 20 consecutive balls at 5 horizontal positions and 4 vertical position. The
last program is constantly saved, also after resetting or power off the machine.
Because the machine saves the program but the remote control doesn’t, the remote control will
show at the display that no balls were programmed after a power off of the machine. Therefor
you’d better look at the display of the machine if there are still balls programmed in the machine
after the remote control has been turned off and on.
When there are still some balls programmed, the next programmed ball will always be added at
the end of the program-series. A ball in the middle of a series could be removed but not added
inside a series of programmed balls. In a program series it is not possible to use 2 times the same
position. This means that several (max. 20) balls could be programmed only when the positions
are unique.
Select AC/DC power.
Push button “Pattern” for programming. In the display “30” is displayed at the “random”
position. Also a flashing number is displayed, this number shows the position of the court.
Position 1-5 is just after the net, position 16-20 is at the end of the court close to the baseline.
Go to the right position via the horizontal buttons (“<” en “>”) and vertical buttons (“^” en
“v”) for the first ball position to program and press “Stock” to save this position. The display
shows the saved position by the number that is displayed.
Repeat step 3 for every next ball.
When ready, press the “ON/OFF” button to start shooting the programmed balls. The
machine only displays the programmed balls, not the order of these.

19
Note: 1. Touch softly ‘Pattern’ button the 1st time,to select the self-programming;touch the 2nd
time,to set the random ball shooting; touch the 3rd time, stop the two functions.
2. 1-15 points are suitable for pressurized balls(hard one),6-20 points are suitable for
Non-pressurized balls(soft one). 6-15 points are suitable for neither soft nor hard
balls.
11. Self-programming（Cancel）
Pattern
/
OFF
DC
AC
W/A/N O N /OFF
Stock
Vertical
Horizontal
While the machine doesn’t display the order of the shooting balls at several positions, you should
manage yourself which balls to remove. When removing a programmed ball, the next balls shift
just one position to become the next ball. For example when a series of 5 balls has been
programmed, the 3rd ball could be removed but not changed to another position, in that case the
balls 3, 4 and 5 should be removed and again being programmed.
1．Select AC/DC power
2．Push “Pattern” to select programming
3．Go to the right position via the horizontal buttons (“<” en “>”) and vertical buttons (“^” en
“v”) for the ball you want to remove.
4．Push “W/A/N” to remove the ball.
5．Repeat steps 3 and 4 to remove other balls.
NOTE: All the balls should be removed separately, there is no function to remove all programmed
balls once.
Note: 1. Touch softly ‘Pattern’ button the 1st time,to select the self-programming;touch the 2nd
time,to set the random ball shooting; touch the 3rd time, stop the two functions.
2. The function of the ‘W/A/N’ button become cancel function when you use the
‘Pattern’ button.

20
12. Choose the random ball shooting
AC DC
OFF
     
Pattern ON /O FF
1. Touch softly the “ON/OFF” button and start the machine
2. Touch softly ‘Pattern’ button the 2nd time,to set the random ball shooting. different
combinations of ball speed、fixed、flat stroke、horizontal swing、horizontal displacement、
vertical displaceement、lob、topspin、backspin、wide-line、Among-line、Narrow-line）。
Every program can be changed automatically (30 seconds/program).
3. Touch softly again the “ON/OFF” or “Reset” button, the machine stop working.
Note：1. Touch softly ‘Pattern’ button the 1st time,to select the self-programming;touch the 2nd
time,to set the random ball shooting; touch the 3rd time, stop the two functions.
13. Other functions
a) Reset function: press the button to clear all functions due to mis-operation and other
reasons.(Except the self-program)
b) Function can be switched randomly except topspin and backspin.
c) The battery electric quantity show: when all the lights are on, it means sufficient; when
part of the lights are on ,it means you must charging.
Warning▲
SIBOASI products are the professional sports-goods equipment. We are not responsible
for any legal responsibility if any other people change the products for other purpose and
cause damage.