Siemens FDCIO223 User manual

Building Technologies
Fire Safety
FDCIO223
Input / output module
(transponder)
Technical manual
Valid for product version ES ≤ 45

Technical specifications and availability subject to change without notice.
© Siemens Switzerland Ltd, 2006
We reserve all rights in this document and in the subject thereof. By acceptance of the document the recipient acknowledges these rights
and undertakes not to publish the document in full or in part, nor to make it available to any third party without our prior express written
authorization, nor to use it for any purpose other than for which it was delivered to him.

3
Building Technologies
009122_e1_en_--
Fire Safety
2015-10-06
1About this document ....................................................................................5
2Safety..............................................................................................................9
2.1 Safety instructions ...........................................................................................9
2.2 Safety regulations for the method of operation .............................................11
2.3 Standards and directives complied with........................................................13
2.4 Release Notes...............................................................................................14
3Structure and function................................................................................15
3.1 Overview .......................................................................................................15
3.1.1 Details for ordering.........................................................................16
3.2 Setup .............................................................................................................16
3.2.1 Overview ........................................................................................16
3.2.2 Circuit board view ..........................................................................17
3.2.3 Indication elements ........................................................................18
3.2.3.1 Input/output module status display............................18
3.2.3.2 Status display for the lines ........................................19
3.2.4 Adjustment elements .....................................................................20
3.3 Function.........................................................................................................21
3.3.1 Overview ........................................................................................21
3.3.2 Input/output module primary side ..................................................22
3.3.3 Power supply .................................................................................23
3.3.4 Operation modes ...........................................................................25
3.3.5 Ground fault monitoring .................................................................26
3.4 Input/output configuration options (secondary side) .....................................27
3.4.1 Configuration as a collective detector line (GMT)..........................28
3.4.1.1 Detectors which can be connected ...........................28
3.4.1.2 Detector line design...................................................29
3.4.1.3 Connection of intrinsically safe detectors in ex-zone 131
3.4.1.4 Alarm verification .......................................................32
3.4.1.5 Monitoring..................................................................33
3.4.2 Configuration as a contact input ....................................................33
3.4.3 Configuration as a control line .......................................................35
3.4.3.1 Overview....................................................................35
3.4.3.2 Control without confirmation......................................39
3.4.3.3 Control with confirmation ...........................................40
3.5 Diagnosis levels ............................................................................................41
3.6 Behavior in degraded mode ..........................................................................43
3.7 Accessories ...................................................................................................44
3.7.1 Enclosed accessories ....................................................................44
3.7.2 Optional accessories .....................................................................44
3.7.2.1 Mounting foot FDCM291 ...........................................44
3.7.2.2 DIN rail TS35 .............................................................44
3.7.2.3 Housing FDCH221 ....................................................45
3.7.2.4 Connection terminal DBZ1190AB .............................45
3.7.2.5 M20 x 1.5 metal cable gland .....................................45
3.7.2.6 M20 x 1.5 metal counter nut......................................45
3.7.2.7 Cable ties 2.4 x 137...................................................46

4
Building Technologies
009122_e1_en_--
Fire Safety
2015-10-06
4Planning .......................................................................................................47
4.1 Compatibility..................................................................................................47
4.2 Defining the mounting site and configuration of the lines .............................48
4.3 Planning the detector line..............................................................................48
4.4 Planning the control line ................................................................................49
4.5 Planning contact input ...................................................................................49
4.6 Environmental influences ..............................................................................49
4.7 Filling out the configuration sheet .................................................................50
5Mounting / Installation ................................................................................51
5.1 Installation with housing ................................................................................51
5.2 Installation without housing ...........................................................................53
5.3Connecting input/output module ...................................................................54
6Commissioning ...........................................................................................56
6.1 Calibrating the control line.............................................................................56
7Maintenance / Repair ..................................................................................57
7.1 Status query ..................................................................................................57
7.2 Performance check .......................................................................................57
8Specifications ..............................................................................................58
8.1 Technical data ...............................................................................................58
8.2 Dimensions....................................................................................................62
8.3 Environmental compatibility...........................................................................62
9Annex............................................................................................................63
9.1 Collective compatibility ..................................................................................63
9.2 Configuration sheet .......................................................................................65
10 Index .............................................................................................................67

About this document
5
Building Technologies
009122_e1_en_--
Fire Safety
2015-10-06
1About this document
Goal and purpose
This document contains information on the input/output module (transponder)
FDCIO223. Following the instructions consistently will ensure that the product can
be used safely and without any problems.
This document is only valid for input/output modules FDCIO223 with a product
version (ES) ≤45.
All input/output modules FDCIO223 with a product version (ES) ≥50 are
described in document 09122 from modification index 'f'.
This document is only available from the Customer Support Center CSC,
Tel. [phone].
Target groups
The information in this document is intended for the following target groups:
Target group
Activity
Qualification
Product Manager Is responsible for information passing
between the manufacturer and
regional company.
Coordinates the flow of information
between the individual groups of
people involved in a project.
Has obtained suitable specialist training for
the function and for the products.
Has attended the training courses for
Product Managers.
Project Manager Coordinates the deployment of all
persons and resources involved in the
project according to schedule.
Provides the information required to
run the project.
Has obtained suitable specialist training for
the function and for the products.
Has attended the training courses for Project
Managers.
Installation personnel Assembles and installs the product
components at the place of
installation.
Carries out a performance check
following installation.
Has received specialist training in the area of
building installation technology or electrical
installations.
Commissioning personnel Configure the product at the place of
installation according to customer-
specific requirements.
Check the product operability and
release the product for use by the
operator.
Searches for and corrects
malfunctions.
Has obtained suitable specialist training for
the function and for the products.
Has attended the training courses for
commissioning personnel.
Maintenance personnel Carries out all maintenance work.
Checks that the products are in
perfect working order.
Searches for and corrects
malfunctions.
Has obtained suitable specialist training for
the function and for the products.

About this document
6
Building Technologies
009122_e1_en_--
Fire Safety
2015-10-06
Document identification
Position
Information
Title page Product type
Product designation
Document type
Last page, bottom left Document ID
ID_ModificationIndex_Language_COUNTRY
Edition date
Last page, bottom right Manual
Register
Conventions for text marking
Markups
Special markups are shown in this document as follows:
⊳Requirement for a behavior instruction
⇨Intermediate result of a behavior instruction
⇨End result of a behavior instruction
'Text' Quotation, reproduced identically
<Key> Identification of keys
Supplementary information
The
i
symbol identifies supplementary information such as a tip for an easier
way of working.
Supplementary information is labelled with the 'i' symbol.

About this document
7
Building Technologies
009122_e1_en_--
Fire Safety
2015-10-06
Technical terms
Term
Explanation
ABS Acrylonitrile-butadiene-styrene (plastic)
ASA Acrylic ester-styrene-acrylnitrile (plastic)
EOL Line termination element (end of line)
ES Product version
FDnet/C-NET Addressed detector line
GMT Limit value detection technology (collective)
KMK
Load connection factor for collective devices (collective detector
connection factor)
Collective detector line Non-addressed detector line
LED Light-emitting diode
MC link Maintenance and Commissioning Link; interface to the detector
exchanger and tester
PC Polycarbonate (plastic)
Reference documents
Document ID
Title
009124 Mounting of Input/output module FDCIO223,
Mounting of housing FDCH221
001204 Fire alarm signal in areas at risk of explosion
008331 List of compatibility (for 'Sinteso' product line)
A6V10229261 List of compatibility (for 'Cerberus PRO' product line)
007227 Operation of detector exchanger and tester FDUD292
009718 Operation of intelligent detector tester FDUD293

About this document
8
Building Technologies
009122_e1_en_--
Fire Safety
2015-10-06
Revision history
Document ID
Edition date
Brief description
009122_e1_en_-- 2015-10-06 Revisions for ES ≤45 included.
009122_e_en_-- 2009-11 Housing FDCH29x replaced with FDCH221
Editorial adjustments made.
009122_d_en_-- 2009-07 Editorial changes made.
New 'Index' chapter.
009122_c_en_-- 2007-09 Descriptions of 'Control with confirmation'
removed.
'Alarm verification' chap. corrected; new
'Diagnosis levels' and 'Degraded mode in FDnet'
chap.
Corrections in 'Technical data':
Line separator added
Humidity changed
Protection category IP changed (short name
for housing)
009122_b_en_-- 2006-10 Naming: "Synova 820" and "SynoNet" omitted
New: Chapter 9, annex (collective compatibility)
009122_a_en_-- 2006-05 First edition

Safety
9
Building Technologies
009122_e1_en_--
Fire Safety
2015-10-06
2Safety
2.1 Safety instructions
The safety notices must be observed in order to protect people and property.
The safety notices in this document contain the following elements:
Symbol for danger
Signal word
Nature and origin of the danger
Consequences if the danger occurs
Measures or prohibitions for danger avoidance
Symbol for danger
This is the symbol for danger. It warns of
risks of injury
.
Follow all measures identified by this symbol to avoid injury or death.
Additional danger symbols
These symbols indicate general dangers, the type of danger or possible
consequences, measures and prohibitions, examples of which are shown in the
following table:
General danger Explosive atmosphere
Voltage/electric shock
Laser light
Battery Heat

Safety
10
Building Technologies
009122_e1_en_--
Fire Safety
2015-10-06
Signal word
The signal word classifies the danger as defined in the following table:
Signal word
Danger level
DANGER
DANGER identifies a dangerous situation, which
will result
directly in death or serious injury
if you do not avoid this
situation.
WARNING
WARNING identifies a dangerous situation, which
may
result in death or serious injury
if you do not avoid this
situation.
CAUTION
CAUTION identifies a dangerous situation, which could
result in
slight to
moderately serious injury
if you do not
avoid this situation.
NOTICE NOTICE identifies possible damage to property that may
result from non-observance.
How risk of injury is presented
Information about the risk of injury is shown as follows:
WARNING
Nature and origin of the danger
Consequences if the danger occurs
Measures / prohibitions for danger avoidance
How possible damage to property is presented
Information about possible damage to property is shown as follows:
NOTICE
Nature and origin of the danger
Consequences if the danger occurs
Measures / prohibitions for danger avoidance

Safety
11
Building Technologies
009122_e1_en_--
Fire Safety
2015-10-06
2.2 Safety regulations for the method of operation
National standards, regulations and legislation
Siemens products are developed and produced in compliance with the relevant
European and international safety standards. Should additional national or local
safety standards or legislation concerning the planning, mounting, installation,
operation or disposal of the product apply at the place of operation, then these
must also be taken into account together with the safety regulations in the product
documentation.
Electrical installations
WARNING
Electrical voltage
Electric shock
Work on electrical installations may only be carried out by qualified
electricians or by instructed persons working under the guidance and
supervision of a qualified electrician, in accordance with the electrotechnical
regulations.
Wherever possible disconnect products from the power supply when carrying
out commissioning, maintenance or repair work on them.
Lock volt-free areas to prevent them being switched back on again by mistake.
Label the connection terminals with external external voltage using a
'DANGER External voltage' sign.
Route mains connections to products separately and fuse them with their own,
clearly marked fuse.
Fit an easily accessible disconnecting device in accordance with IEC 60950-1
outside the installation.
Produce earthing as stated in local safety regulations.
Mounting, installation, commissioning and maintenance
If you require tools such as a ladder, these must be safe and must be intended
for the work in hand.
When starting the fire control panel ensure that unstable conditions cannot
arise.
Ensure that all points listed in the 'Testing the product operability' section below
are observed.
You may only set controls to normal function when the product operability has
been completely tested and the system has been handed over to the customer.

Safety
12
Building Technologies
009122_e1_en_--
Fire Safety
2015-10-06
Testing the product operability
Prevent the remote transmission from triggering erroneously.
If testing building installations or activating devices from third-party companies,
you must collaborate with the people appointed.
The activation of fire control installations for test purposes must not cause injury
to anyone or damage to the building installations. The following instructions
must be observed:
‒Use the correct potential for activation; this is generally the potential of the
building installation.
‒Only check controls up to the interface (relay with blocking option).
‒Make sure that only the controls to be tested are activated.
Inform people before testing the alarming control devices and allow for possible
panic responses.
Inform people about any noise or mist which may be produced.
Before testing the remote transmission, inform the corresponding alarm and
fault signal receiving stations.
Modifications to the system design and the products
Modifications to the system and to individual products may lead to faults,
malfunctioning and safety risks. Written confirmation must be obtained from
Siemens and the corresponding safety bodies for modifications or additions.
Modules and spare parts
Components and spare parts must comply with the technical specifications
defined by Siemens. Only use products specified or recommended by Siemens.
Only use fuses with the specified fuse characteristics and which have been
adapted to the connected load.
Wrong battery types and improper battery changing lead to a risk of explosion.
Only use the same battery type or an equivalent battery type recommended by
Siemens.
Batteries must be disposed of in an environmentally friendly manner. Observe
national guidelines and regulations.

Safety
13
Building Technologies
009122_e1_en_--
Fire Safety
2015-10-06
Disregard of the safety regulations
Before they are delivered, Siemens products are tested to ensure they function
correctly when used properly. Siemens disclaims all liability for damage or injuries
caused by the incorrect application of the instructions or the disregard of danger
warnings contained in the documentation. This applies in particular to the following
damage:
Personal injuries or damage to property caused by improper use and incorrect
application
Personal injuries or damage to property caused by disregarding safety
instructions in the documentation or on the product
Personal injury or damage to property caused by poor maintenance or lack of
maintenance
Disclaimer
We have checked that the content of this document matches the hardware and
software described. Despite this, we cannot rule out deviations and cannot
therefore assume liability for them matching completely. The details in this
document are checked regularly and any corrections needed included in
subsequent editions.
We are grateful for any suggestions for improvement.
2.3 Standards and directives complied with
A list of the standards and directives complied with is available from your Siemens
contact.

Safety
14
Building Technologies
009122_e1_en_--
Fire Safety
2015-10-06
2.4 Release Notes
Limitations to the configuration or use of devices in a fire detection installation with
a particular firmware version are possible.
WARNING
Limited or non-existent fire detection
Personal injury and damage to property in the event of a fire.
Read the 'Release Notes' before you plan and/or configure a fire detection
installation.
Read the 'Release Notes' before you carry out a firmware update to a fire
detection installation.
NOTICE
Incorrect planning and/or configuration
Important standards and specifications are not satisfied.
Fire detection installation is not accepted for commissioning.
Additional expense resulting from necessary new planning and/or configuration.
Read the 'Release Notes' before you plan and/or configure a fire detection
installation.
Read the 'Release Notes' before you carry out a firmware update to a fire
detection installation.

Structure and function
15
Building Technologies
009122_e1_en_--
Fire Safety
2015-10-06
3Structure and function
3.1 Overview
The input/output module FDCIO223 is operated on the FDnet/C-NET and features
two inputs/outputs. These can be configured as follows:
Collective detector line
Control line
Contact input
The figure below shows the integration of the module in the fire detection system.
Input/output module in the fire detection system
Properties
Connection of two collective detector lines to the FDnet/C-NET
Connection of monitored or non-monitored contacts
Monitored control of equipment
Built-in line separator
Compatible with AlgoRex, SIGMASYS, and FS20/FS720 fire detection systems
With the safety barrier, it is also possible to connect intrinsically safe detectors
(ex-zones 1 and 2)
If the input/output module FDCIO223 is operated in conjunction with a fire
detection system FS20/FS720, only collective detector lines and monitored
equipment control are supported. It is not possible for contacts to be connected.

Structure and function
16
Building Technologies
009122_e1_en_--
Fire Safety
2015-10-06
3.1.1 Details for ordering
Type
Order no.
Designation
FDCIO223 S24218-B102-A1 Input / output module (transponder)
See also
Enclosed accessories [44]
3.2 Setup
The modules consist of the module carrier, the printed circuit board and the cover
cap. The printed circuit board includes LEDs. These indicate the status of the
inputs and outputs and the operating condition.
The cover of the printed circuit board is transparent, so that the state of the LEDs is
visible even when the housing is closed.
To protect the modules from environmental influences, the FDCH221 housing
(accessories) is available.
3.2.1 Overview
Overview
1 Cable tie holder 3 Holes for mounting feet FDCM291
2 Bores for wall mounting 4Push button for calibrating control
lines

Structure and function
17
Building Technologies
009122_e1_en_--
Fire Safety
2015-10-06
3.2.2 Circuit board view
1
2
3
4
5
6
7
8
91011111212
17
17
16
15
13
13
14
EN54-18:2005
EN54-17:2005
IdN
r.
G206054
Circuit board view
1 Ground connection
2 Shielding connection for inputs/outputs 'I/O 1' and 'I/O 2'
3 Connection for input/output 'I/O 2'
4Connection for input/output 'I/O 1'
5Jumper for polarization of monitoring for input/output 'I/O 2'
6 Jumper for polarization of monitoring for input/output 'I/O 1'
7 Push button for calibrating control lines
8Jumper for ground fault monitoring of inputs/outputs 'I/O 1' and 'I/O 2'
9 LEDs for indicating the status of input/output 'I/O 2'
10 LEDs for indicating the status of input/output 'I/O 1'
11 LEDs for indicating the status of the input/output module's secondary side
12 LEDs for indicating the status of the input/output module's primary side
13 Connectors for the FDnet/C-NET detector line
14 Connection for the detector exchanger and tester (MC link)
15 Connection for the FDnet/C-NET detector line shielding
16 Connection for the 24 V supply shielding
17 Connection for the 24 V secondary side supply

Structure and function
18
Building Technologies
009122_e1_en_--
Fire Safety
2015-10-06
3.2.3 Indication elements
3.2.3.1 Input/output module status display
Primary side LEDs
Green
'PWR PRIM'
(Ref 12)
Yellow
'FAULT PRIM'
(Ref 12)
Meaning
Flashes every 4 s Off Normal condition
Flashes every 4 s Flashes every 4 s Test mode
Flashes every 4 s Flashes once a
second
Localization mode
Off Off Fault:
No FDnet/C-NET supply voltage
Input/output module faulty
Off Flashes every 4 s Fault:
No supply voltage (24 V)
Fault on input/output line, e.g., short circuit
or open line
Off Single pulse every
second and double
pulse every
4seconds
Input/output module is in localization mode and
there is a fault pending
What the LEDs mean: Input/output module status (primary side)
Secondary side LEDs
Green
'PWR SEC'
(Ref 11)
Yellow
'FAULT SEC'
(Ref 11)
Meaning
Off Off Fault:
No supply voltage (24 V)
Input/output module faulty
Flashes once a
second
Off Normal operation
Flashes once a
second
ON Fault:
Input/output module faulty
Ground fault
Error on FDnet/C-NET detector line
What the LEDs mean: Input/output module status (secondary side)

Structure and function
19
Building Technologies
009122_e1_en_--
Fire Safety
2015-10-06
3.2.3.2 Status display for the lines
There are both red and green LEDs for each input/output and these are used to
indicate the status (LED 'I/O 1' and 'I/O 2'). Their meaning depends on how the
input/output is configured.
Input/output is configured as an input
(detector line or contact input)
Green
'I/O 1' / 'I/O 2'
(Ref 10 / 9)
Red
'I/O 1' / 'I/O 2'
(Ref 10 / 9)
State
Off Off Not active
No supply
Incorrectly configured
ON Off Standby
Off ON Alarm
ON ON Fault:
Open line
Short-circuit
Deviation in terms of monitoring
resistances (only in the case of a contact
input)
Off Flashes Triggered in inspection mode/test mode
What the LEDs mean (detector line or contact input)
Input/output is configured as an output (control line)
Green
'I/O 1' / 'I/O 2'
(Ref 10 / 9)
Red
'I/O 1' / 'I/O 2'
(Ref 10 / 9)
State
Off Off Not active
No supply
Incorrectly configured
ON Off Standby
Off ON Output activated
ON ON Fault:
Open line
Short-circuit
Control line not calibrated
Off Flashes Inspection mode/test mode
Flashes every
0.5 s
Off Calibration of load resistances
Off ON for 2 seconds Calibration of load resistances not permitted
What the LEDs mean (control line)

Structure and function
20
Building Technologies
009122_e1_en_--
Fire Safety
2015-10-06
3.2.4 Adjustment elements
off
on
invert
norm
invert
norm
Supervision
I/O 1 I/O 2
adjust
Adjustment elements
Legend
Jumper
Function
Position
Meaning
(Ref 8)
Ground fault monitoring on 1Activated
off Deactivated
Supervision
I/O 1
(Ref 6)
Input/output 1:
Polarity during monitoring
norm 1Setting for:
Control line featuring identical-polarity monitoring
Detector line
Contact input
invert Setting for:
Control line featuring reverse-polarity monitoring
Supervision
I/O 2
(Ref 5)
Input/output 2:
Polarity during monitoring
norm 1Setting for:
Control line featuring identical-polarity monitoring
Detector line
Contact input
invert Setting for:
Control line featuring reverse-polarity monitoring
Adjustment elements
1 Jumper setting shown in the figure (corresponds to factory setting)