Siemens SIMATIC ET 200SP User manual

Product information on the
documentation of the
ET 200SP distributed I/O system
___________________
___________________
___________________
SIMATIC
ET 200SP
Product information on the documentation of the
ET 200SP distributed I/O system
Product Information
12/2014
A5E03799595
-AL
Preface
Overview of the ET 200SP
1
General additions to the
documentation
2

Siemens AG
Division Digital Factory
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E03799595-AL
Ⓟ
12/2014 Subject to change
Copyright © Siemens AG 2012 - 2014.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by
personnel qualified
for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

Product information on the documentation of the ET 200SP distributed I/O system
Product Information, 12/2014, A5E03799595-AL 3
Preface
Validity
This product information supplements the documentation for the ET 200SP and takes
precedence over our system manuals, function manuals and product manuals.
Security information
For the secure operation of Siemens products and solutions, it is necessary to take suitable
preventive action (e.g. cell protection concept) and integrate each component into a holistic,
state-of-the-art industrial security concept. Third-party products that may be in use should
also be considered. You can find more information about industrial security on the Internet
(http://www.siemens.com/industrialsecurity).

Product information on the documentation of the ET 200SP distributed I/O system
4Product Information, 12/2014, A5E03799595-AL
Table of contents
Preface ................................................................................................................................................... 3
1 Overview of the ET 200SP...................................................................................................................... 5
2 General additions to the documentation ................................................................................................ 15

Product information on the documentation of the ET 200SP distributed I/O system
Product Information, 12/2014, A5E03799595-AL 5
Overview of the ET 200SP
1
Contents
This product information includes amendments and corrections to the documentation of the
ET 200SP distributed I/O system
(http://support.automation.siemens.com/WW/view/en/55679227/133300).
Which I/O modules are compatible with a BaseUnit?
The following table provides an overview of the I/O modules that are compatible with the
associated BaseUnits:
Table 1- 1 Possible combinations of BaseUnits and I/O modules
I/O
module
BaseUnit BU15-
BaseUnit BU20-
Color-coded
label for pro-
cess terminals
BU type A0
P16+A10+2D
P16+A0+2D
P16+A10+2B
P16+A0+2B
BU type A1
P16+A0+12D/T
P16+A0+2D/T
P16+A0+12B/T
P16+A0+2B/T
BU type B0
P12+A4+0B
BU type B1
P12+A0+4B
BU type
C0
P6+A2+4D
BU type
C1
P6+A2+4B
BU type D0
P12+A0+0B
BU type
F0
P8+A4+0B
Digital I/O modules
DI
16x24VDC
ST
✓--- ---
DI
8x24VDC
ST
✓CC01
DI
8x24VDC
HF
✓CC01
DI
8x24VDC
SRC BA
✓CC02
DI
8xNAMUR
HF
✓CC01

Overview of the ET 200SP
Product information on the documentation of the ET 200SP distributed I/O system
6Product Information, 12/2014, A5E03799595-AL
I/O
module
BaseUnit BU15-
BaseUnit BU20-
Color-coded
label for pro-
cess terminals
BU type A0
P16+A10+2D
P16+A0+2D
P16+A10+2B
P16+A0+2B
BU type A1
P16+A0+12D/T
P16+A0+2D/T
P16+A0+12B/T
P16+A0+2B/T
BU type B0
P12+A4+0B
BU type B1
P12+A0+4B
BU type
C0
P6+A2+4D
BU type
C1
P6+A2+4B
BU type D0
P12+A0+0B
BU type
F0
P8+A4+0B
DI
4x120..23
0VAC ST
✓CC41
DQ
16x24VDC
/0.5A ST
✓--- ---
DQ
4x24VDC/
2A ST
✓CC02
DQ
8x24VDC/
0.5 ST
✓CC02
DQ
8x24VDC/
0.5A HF
✓CC02
DQ
8x24VDC/
0.5A SNK
BA
✓CC01
DQ
4x24..230
VAC/2A
ST
✓CC41
DQ
4x24VDC/
2A HF
✓CC02
RQ
4x24VUC/
2A CO ST
✓--- ---
RQ
4x120VDC
-
230VAC/5
A NO ST
✓--- ---

Overview of the ET 200SP
Product information on the documentation of the ET 200SP distributed I/O system
Product Information, 12/2014, A5E03799595-AL 7
I/O
module
BaseUnit BU15-
BaseUnit BU20-
Color-coded
label for pro-
cess terminals
BU type A0
P16+A10+2D
P16+A0+2D
P16+A10+2B
P16+A0+2B
BU type A1
P16+A0+12D/T
P16+A0+2D/T
P16+A0+12B/T
P16+A0+2B/T
BU type B0
P12+A4+0B
BU type B1
P12+A0+4B
BU type
C0
P6+A2+4D
BU type
C1
P6+A2+4B
BU type D0
P12+A0+0B
BU type
F0
P8+A4+0B
Analog I/O modules
AI
4xRTD/TC
2-/3-/4-
wire HF
✓✓--- ---
AI
8xRTD/TC
2-wire HF
✓✓--- ---
AI 4xU/I 2-
wire ST
✓✓CC03
AI 2xU/I 2-
/4-wire HF
✓✓CC05
AI 2xU/I 2-
/4-wire HS
✓✓--- ---
AI 4xI 2-
/4-wire ST
✓✓CC03
AI 4xI 2-
wire
4...20mA
HART
✓✓CC03
AQ 4xU/I
ST
✓✓--- ---
AQ 2xU/I
HS
✓✓--- ---
AQ 2xU/I
HF
✓✓--- ---
AI Energy
Meter ST
✓--- ---
Fail-safe modules
F-PM-E
24VDC/8A
PPM ST
✓CC52
F-DI
8x24VDC
HF
✓CC01

Overview of the ET 200SP
Product information on the documentation of the ET 200SP distributed I/O system
8Product Information, 12/2014, A5E03799595-AL
I/O
module
BaseUnit BU15-
BaseUnit BU20-
Color-coded
label for pro-
cess terminals
BU type A0
P16+A10+2D
P16+A0+2D
P16+A10+2B
P16+A0+2B
BU type A1
P16+A0+12D/T
P16+A0+2D/T
P16+A0+12B/T
P16+A0+2B/T
BU type B0
P12+A4+0B
BU type B1
P12+A0+4B
BU type
C0
P6+A2+4D
BU type
C1
P6+A2+4B
BU type D0
P12+A0+0B
BU type
F0
P8+A4+0B
F-DQ
4x24VDC/
2A PM HF
✓CC02
F-RQ
1x24VDC/
24..230VA
C/5A
✓CC42
Communication modules
CM 4xIO-
Link
✓CC04
CM AS-i
Master ST
✓--- ---
F-CM AS-i
Safety ST
✓✓--- ---
CM PtP
✓
---
---
Technology modules
TM Count
1x24V
✓--- ---
TM PosIn-
put 1
✓--- ---
SIWAREX
WP321
✓--- ---

Overview of the ET 200SP
Product information on the documentation of the ET 200SP distributed I/O system
Product Information, 12/2014, A5E03799595-AL 9
Components of the ET 200SP
Table 1- 2 CPU
Interface modules
Number in pack
Article number
CPU 1510SP-1 PN with server module
Pack of 1
6ES7510-1DJ00-0AB0
CPU 1512SP-1 PN with server module
Pack of 1
6ES7512-1DK00-0AB0
Table 1- 3 Interface modules
Interface modules
Number in pack
Article number
Interface module IM 155-6 PN ST
•with BusAdapter BA 2xRJ45 and server module Pack of 1 6ES7155-6AA00-0BN0
•with server module Pack of 1 6ES7155-6AU00-0BN0
Interface module IM 155-6 PN HF with server module Pack of 1 6ES7155-6AU00-0CN0
Interface module IM 155-6 DP HF with PROFIBUS FastConnect
bus connector (6ES7972-0BB70-0XA0) and server module
Pack of 1 6ES7155-6BA00-0CN0
Important differences between the interface modules
Features
IM 155-6 PN ST
IM 155-6 PN HF
IM 155-6 DP HF
Bus connection BusAdapter BA 2xRJ45 or
BA 2xFC
BusAdapter BA 2xRJ45,
BA 2xFC and BA 2xSCRJ
PROFIBUS DP connection
socket
Number of modules
32
64
32
RESET button
Yes
Yes
Not necessary
Address space (I/O data) in
bytes
256 1440 244
Multi hot-swapping
No
Yes
Yes

Overview of the ET 200SP
Product information on the documentation of the ET 200SP distributed I/O system
10 Product Information, 12/2014, A5E03799595-AL
Table 1- 4 BaseUnits
BU type
BaseUnits (short name)
Number in pack
Color-coded labels*
Article number
A0 BU15-P16+A10+2D Pack of 1
P16:
CC01 to CC05
A10: CC71 to CC73
6ES7193-6BP20-0DA0
A0 BU15-P16+A0+2D Pack of 1
P16:
CC01 to CC05 6ES7193-6BP00-0DA0
A0 BU15-P16+A10+2B Pack of 1
P16:
CC01 to CC05
A10: CC71 to CC73
6ES7193-6BP20-0BA0
A0
BU15-P16+A0+2B
Pack of 1
P16: CC01 to CC05
6ES7193-6BP00-0BA0
A1 BU15-P16+A0+12D/T Pack of 1
P16:
CC01 to CC05
12D: CC74
6ES7193-6BP40-0DA1
A1
BU15-P16+A0+2D/T
Pack of 1
P16: CC01 to CC05
6ES7193-6BP00-0DA1
A1 BU15-P16+A0+12B/T Pack of 1
P16:
CC01 to CC05
12B: CC74
6ES7193-6BP40-0BA1
A1
BU15-P16+A0+2B/T
Pack of 1
P16: CC01 to CC05
6ES7193-6BP00-0BA1
B0
BU20-P12+A4+0B
Pack of 1
A4: CC81 to CC83
6ES7193-6BP20-0BB0
B1
BU20-P12+A0+4B
Pack of 1
P12: CC41
6ES7193-6BP20-0BB1
C0 BU20-P6+A2+4D Pack of 1
P6:
CC51, CC52
A2: CC84 to CC86
6ES7193-6BP20-0DC0
C1 BU20-P6+A2+4B Pack of 1
P6:
CC51
A2: CC84 to CC86
6ES7193-6BP20-0BC1
D0
BU20-P12+A0+0B
Pack of 1
---
6ES7193-6BP00-0BD0
F0
BU20-P8+A4+0B
Pack of 1
P8: CC42
6ES7193-6BP20-0BF0
* not shipped with the BaseUnit
Table 1- 5 Digital I/O modules
Digital I/O modules
Number in pack
Article number
DI 16x24VDC ST
Pack of 1
6ES7131-6BH00-0BA0
DI 8x24VDC ST
Pack of 1
6ES7131-6BF00-0BA0
DI 8x24VDC HF
Pack of 1
6ES7131-6BF00-0CA0
DI 8xNAMUR HF
Pack of 1
6ES7131-6FD00-0BB1
DI 8x24VDC SRC BA
Pack of 1
6ES7131-6BF60-0AA0
DI 4x120..230VAC ST
Pack of 1
6ES7131-6FD00-0BB1
DQ 16x24VDC ST
Pack of 1
6ES7132-6BH00-0BA0
DQ 8x24VDC/0.5A ST
Pack of 1
6ES7132-6BF00-0BA0
DQ 8x24VDC/0.5A HF
Pack of 1
6ES7132-6BF00-0CA0
DQ 8x24VDC/0.5A SNK BA
Pack of 1
6ES7132-6BF60-0AA0
DQ 4x24VDC/2A ST
Pack of 1
6ES7132-6BD20-0BA0
DQ 4x24..230VAC/2A ST
Pack of 1
6ES7132-6FD00-0BB1
DQ 4x24VDC/2A HF
Pack of 1
6ES7132-6BD20-0CA0
RQ 4x24VUC/2A CO ST
Pack of 1
6ES7132-6GD50-0BA0
RQ 4x120VDC-230VAC/5A NO ST
Pack of 1
6ES7132-6HD00-0BB0

Overview of the ET 200SP
Product information on the documentation of the ET 200SP distributed I/O system
Product Information, 12/2014, A5E03799595-AL 11
Table 1- 6 Analog I/O modules
Analog I/O modules
Number in pack
Article number
AI 4xU/I 2-wire ST
Pack of 1
6ES7134-6HD00-0BA1
AI 2xU/I 2-/4-wire HF
Pack of 1
6ES7134-6HB00-0CA1
AI 2xU/I 2-/4-wire HS
Pack of 1
6ES7134-6HB00-0DA1
AI 4xI 2-/4-wire ST Pack of 1 6ES7134-6GD00-0BA1
AI 8xRTD/TC 2-wire HF
Pack of 1
6ES7134-6JF00-0CA1
AI 4xRTD/TC 2-/3-/4-wire HF
Pack of 1
6ES7134-6JD00-0CA1
AI 4xI 2-wire 4...20mA HART
Pack of 1
6ES7134-6TD00-0CA1
AQ 4xU/I ST
Pack of 1
6ES7135-6HD00-0BA1
AQ 2xU/I HF
Pack of 1
6ES7135-6HB00-0CA1
AQ 2xU/I HS
Pack of 1
6ES7135-6HB00-0DA1
AI Energy Meter ST
Pack of 1
6ES7134-6PA00-0BD0
Table 1- 7 Fail-safe modules
Fail-safe modules
Number in pack
Article number
F-PM-E 24VDC/8A PPM ST
Pack of 1
6ES7136-6PA00-0BC0
F-DI 8x24VDC HF
Pack of 1
6ES7136-6BA00-0CA0
F-DQ 4x24VDC/2A PM HF
Pack of 1
6ES7136-6DB00-0CA0
F-RQ 1x24VDC/24..230VAC/5A
Pack of 1
6ES7136-6RA00-0BF0
Table 1- 8 Communication modules
Communication modules
Number in pack
Article number
CM 4xIO-Link
Pack of 1
6ES7137-6BD00-0BA0
CM AS-i Master ST
Pack of 1
3RK7137-6SA00-0BC1
F-CM AS-i Safety ST
Pack of 1
3RK7136-6SC00-0BC1
CM PtP
Pack of 1
6ES7137-6AA00-0BA0
CM DP (for CPU)
Pack of 1
6ES7545-5DA00-0AB0
Table 1- 9 Technology module
Technology module
Number in pack
Article number
TM Count 1x24V
Pack of 1
6ES7138-6AA00-0BA0
TM PosInput 1
Pack of 1
6ES7138-6BA00-0BA0
SIWAREX WP321 Pack of 1 7MH4138-6AA00-0BA0

Overview of the ET 200SP
Product information on the documentation of the ET 200SP distributed I/O system
12 Product Information, 12/2014, A5E03799595-AL
Table 1- 10 Station expansion via ET-Connection (mixed configuration ET 200SP/ET 200AL)
Modules
Number in pack
Article number
BU-Send
Pack of 1
6ES7193-6BN00-0NE0
BA-Send 1xFC
Pack of 1
6ES7193-6AS00-0AA0
Table 1- 11 General accessories
General accessories
Number in pack
Article number
BusAdapter
•BA 2×RJ45 (PROFINET BusAdapter with standard
Ethernet socket for IM-PN)
Pack of 1 6ES7193-6AR00-0AA0
•BA 2×FC (PROFINET BusAdapter with FastConnect
Ethernet connector for IM-PN)
Pack of 1 6ES7193-6AF00-0AA0
•BA 2xSCRJ (PROFINET BusAdapter with fiber-optic
cable connector for IM-PN)
Pack of 1 6ES7193-6AP00-0AA0
PROFIBUS FastConnect bus
connector
Pack of 1 6ES7972-0BB70-0XA0
Server module (spare part)
Pack of 1
6ES7193-6PA00-0AA0
BU cover
•15 mm wide Pack of 5 6ES7133-6CV15-1AM0
•20 mm wide Pack of 5 6ES7133-6CV20-1AM0
Shield connector for BaseUnit (shield contacts and shield
terminals)
Pack of 5 6ES7193-6SC00-1AM0
Equipment labeling plate, sheet with 16 labels
Pack of 10
6ES7193-6LF30-0AW0
Labeling strips (for labeling the I/O modules)
•Roll, light gray (with a total of 500 labeling strips) Pack of 1 6ES7193-6LR10-0AA0
•Roll, yellow (with a total of 500 labeling strips) Pack of 1 6ES7193-6LR10-0AG0
•DIN A4 sheets, light gray (with a total of 1000 labeling
strips)
Pack of 10 6ES7193-6LA10-0AA0
•DIN A4 sheets, yellow (with a total of 1000 labeling
strips)
Pack of 10 6ES7193-6LA10-0AG0
Mounting rails, tin-plated steel strip
•Length: 483 mm Pack of 1 6ES5710-8MA11
•Length: 530 mm Pack of 1 6ES5710-8MA21
•Length: 830 mm Pack of 1 6ES5710-8MA31
•Length 2000 mm Pack of 1 6ES5710-8MA41

Overview of the ET 200SP
Product information on the documentation of the ET 200SP distributed I/O system
Product Information, 12/2014, A5E03799595-AL 13
Table 1- 12 Accessories color-coded labels (push-in terminals), 15 mm wide
Accessories color-coded labels (push-in ter-
minals), 15 mm wide
Number in pack
Article number
16 process terminals (see manual for I/O module)
•Gray (terminals 1 to 8), red (terminals 9 to
16); color code CC01
Pack of 10 6ES7193-6CP01-2MA0
•
Gray (terminals 1 to 8), blue (terminals 9 to
16); color code CC02
Pack of 10
6ES7193-6CP02-2MA0
•Gray (terminals 1 to 8), red (terminals 9 to
12), gray (terminals 13 to 16); color code
CC03
Pack of 10 6ES7193-6CP03-2MA0
•Gray (terminals 1 to 8), red (terminals 9 to
12), blue (terminals 13 to 16); color code
CC04
Pack of 10 6ES7193-6CP04-2MA0
•Gray (terminals 1 to 12), red (terminals 13
and 14), blue (terminals 15 and 16);
color code CC05
Pack of 10
6ES7193-6CP05-2MA0
10 AUX terminals (for BU15-P16+A10+2D, BU15-P16+A10+2B)
•Yellow-green (terminals 1A to 10A); color
code CC71
Pack of 10 6ES7193-6CP71-2AA0
•Red (terminals 1A to 10A); color code
CC72
Pack of 10 6ES7193-6CP72-2AA0
•Blue (terminals 1A to 10A); color code
CC73
Pack of 10 6ES7193-6CP73-2AA0
10 add-on terminals (for BU15-P16+A0+12D/T, BU15-P16+A0+12B/T)
•Red (terminals 1B to 5B), blue (terminals
1C to 5C); color code CC74
Pack of 10
6ES7193-6CP74-2AA0

Overview of the ET 200SP
Product information on the documentation of the ET 200SP distributed I/O system
14 Product Information, 12/2014, A5E03799595-AL
Table 1- 13 Accessories color-coded labels (push-in terminals), 20 mm wide
Accessories color-coded labels (push-in ter-
minals), 20 mm wide
Number in pack
Article number
12 process terminals (see manual for I/O module)
•Gray (terminals 1 to 4), red (terminals 5 to
8), blue (terminals 9 to 12); color code
CC41
Pack of 10 6ES7193-6CP41-2MB0
•Gray (terminals 1 to 8), red (terminals 9
and 10), blue (terminals 11 and 12), color
code CC42
Pack of 10 6ES7193-6CP42-2MB0
6 process terminals (see manual for I/O module)
•Gray (terminals 1 to 4), red (terminal 5),
blue (terminal 6); color code CC51
Pack of 10 6ES7193-6CP51-2MC0
•Gray (terminals 1, 2 and 5), red (terminals
3 and 4), blue (terminal 6); color code
CC52
Pack of 10 6ES7193-6CP52-2MC0
4 AUX terminals (for BU20-P12+A4+0B)
•Yellow-green (terminals 1A to 4A); color
code CC81
Pack of 10 6ES7193-6CP81-2AB0
•Red (terminals 1A to 4A); color code
CC82
Pack of 10 6ES7193-6CP82-2AB0
•Blue (terminals 1A to 4A); color code
CC83
Pack of 10 6ES7193-6CP83-2AB0
2 AUX terminals (for BU20-P6+A2+4D, BU20-P6+A2+4B)
•Yellow-green (terminals 1A and 2A); color
code CC84
Pack of 10 6ES7193-6CP84-2AC0
•Red (terminals 1A and 2A); color code
CC85
Pack of 10 6ES7193-6CP85-2AC0
•Blue (terminals 1A and 2A); color code
CC86
Pack of 10 6ES7193-6CP86-2AC0

Product information on the documentation of the ET 200SP distributed I/O system
Product Information, 12/2014, A5E03799595-AL 15
General additions to the documentation
2
System Manual ET 200SP Distributed I/O System, Edition 07/2014
Section 5.9.2 Connecting PROFINET IO to the CPU/interface module via the
BusAdapter BA 2xFC
Fast Connect Cable (recommended types):
●IE FC TP Standard Cable GP 2x2 (6XV1840-2AH10)
●IE FC TP Trailing Cable 2x2 (6XV1840-3AH10)
●IE FC TP Marine Cable (6XV1840-4AH10)
●IE FC TP Flexible Cable GP 2x2 (6XV1870-2B)
●IE FC TP Trailing Cable 2x2 (6XV1870-2D)
●IE TP Torsion Cable 2x2 (6XV1870-2F)
●FC TP FRNC Cable GP (6XV1871-2F)
●IE FC TP Food Cable GP 2x2 (6XV1871-2L)
●IE FC TP Festoon Cable 2x2 (6XV1871-2S)
Section 9.1 Removing and inserting I/O modules
NOTICE
Reaction of the CPU when removing and inserting the ET 200SP server module
Please note that the backplane bus is deactivated when you pull the server module,
regardless of the CPU operating state. Also note that the outputs do not accept their
configured substitute value behavior when you pull the server module.
This means you should not pull the server module in the CPU operating states STARTUP,
RUN and STOP.
Section 14.1 Standards and approvals
Note
Shipbuilding approval
A shipbuilding approval is currently not available for the ET 200AL distributed I/O system.
Keep this in mind when operating the ET 200SP in combination with
ET 200AL via an ET
connection.

General additions to the documentation
Product information on the documentation of the ET 200SP distributed I/O system
16 Product Information, 12/2014, A5E03799595-AL
Function manuals for the CPUs
The following function manuals are valid for the CPU 1510SP-1 PN (6ES7510-1DJ00-0AB0)
and CPU 1512SP-1 PN (6ES7512-1DK00-0AB0):
Topic
Documentation
Most important contents
Memory concept Structure and Use of the CPU
Memory
(http://support.automation.sie
mens.com/WW/view/en/59193
101)
•Structure
•Application
Trace and logic analyzer function Using the trace and logic ana-
lyzer function
(http://support.automation.sie
mens.com/WW/view/en/64897
128)
•Software user interface
•Operation
•Devices
Communication Web server
(http://support.automation.sie
mens.com/WW/view/en/59193
560)
•Basics
•Functions
•Operation
Cycle and response times Cycle and response times
(http://support.automation.sie
mens.com/WW/view/en/59193
558)
•Basics
•Calculations
Device manuals IM 155-6 PN ST, edition 12/2014; IM 155-6 PN HF, edition 12/2014
As of firmware V3.x, the interface modules support inserting dark BaseUnits in slot 1. This
means that starting with slot 1, you can now also configure modules which do not have a
connection to the integrated busbars P1 and P2. The following modules are currently
included:
●AI EnergyMeter ST (6ES7134-6PA00-0BD0)
●DI 4x120..230VAC ST (6ES7131-6FD00-0BB1)
●DQ 4x24..230VAC/2A ST (6ES7132-6FD00-0BB1)
Requirement for configuration of these modules in slot 1:
●Configuration via GSD or GSDML
●Configuration as of STEP7 V5.5 SP4 with
–HSP0241 V2.0 for IM155-6 PN ST
–HSP0242 V2.0 for IM155-6 DP HF
–HSP0255 V3.0 for IM155-6 PN HF
●Configuration as of STEP7 V13 SP1

General additions to the documentation
Product information on the documentation of the ET 200SP distributed I/O system
Product Information, 12/2014, A5E03799595-AL 17
Device manual IM 155-6 PN ST, edition 12/2014
Section 2.2 Functions
As of firmware version V3.1, the interface module IM 155-6 PN ST supports the "Position
input for Motion Control" mode of the technology modules TM Count 1x24V (6ES7138-
6AA00-0BA0) and TM PosInput 1 (6ES7138-6BA00-0BA0).
Configuration of I/O modules ST with HSP in STEP 7 V5.5 SP3
I/O module
Order number
Firmware version
STEP 7 V5.5 SP3
DI 8x24VDC ST 6ES7131-6BF00-
0BA0
V1.1.0 HSP0229 V4.0
DQ 4x24VDC/2A ST 6ES7132-6BD20-
0BA0
V1.1.0 HSP0230 V4.0
DQ 8x24VDC/0.5A ST 6ES7132-6BF00-
0BA0
V1.1.0 HSP0230 V4.0
RQ 4x120VDC-230VAC/5A NO
ST
6ES7132-6HD00-
0BB0
V1.1.0 HSP0232 V4.0
AI 4xI 2-/4-wire ST 6ES7134-6GD00-
0BA1
V1.1.0 HSP0027 V4.0
AI 4xU/I 2-wire ST 6ES7134-6HD00-
0BA1
V1.1.0 HSP0027 V4.0
AI Energy Meter ST 6ES7134-6PA00-
0BD0
V2.0.0 HSP0027 V4.0
AQ 4xU/I ST 6ES7135-6HD00-
0BA1
V1.1.0 HSP0228 V4.0
Manual DI 8x24VDC HF, Edition 02/2014
Section 6.1 Technical specifications
●24 V sensor supply
–Output current, max.: 700 mA, Total current
Device manual DI 8xNAMUR HF, Edition 02/2014
Section A.2 Parameter assignment and structure of the parameter data record
With data records 0 to 7, you can configure the individual channels.
When using the interface module IM 155-6 DP HF (PROFIBUS DP), the module returns the
diagnostics data record back when data records 0 and 1 are read, and not the parameter
data record of the DI 8xNAMUR HF.

General additions to the documentation
Product information on the documentation of the ET 200SP distributed I/O system
18 Product Information, 12/2014, A5E03799595-AL
DQ 16x24VDC/0.5A ST, DQ 8x24VDC/0.5A HF digital output module manual
Safety-related shutdown of the ET 200SP with digital output module DQ 16x24VDC/0.5A ST,
DQ 8x24VDC/0.5A HF
Note
The digital output module DQ 16x24VDC/0.5A ST, DQ 8x24VDC/0.5A HF supports safety
-
related
shutdown in connection with a fail-safe power module F-PM-E 24VDC/8A PPM ST:
•
SIL according to IEC 61508: 2
•
Highest attainable safety class in safety mode, performance level according to EN ISO
13849-1: d

General additions to the documentation
Product information on the documentation of the ET 200SP distributed I/O system
Product Information, 12/2014, A5E03799595-AL 19
RQ 4x24VUC/2A CO ST digital output module manual, Edition 02/2014
Section 4.3 address space
Configuration options for the RQ 4x24VUC/2A CO ST digital output module:
The following configurations are possible:
●Configuration 1: without value status
●Configuration 2: with value status
Evaluating the value status
:
An additional byte is allocated in the input address space if you enable the value status for
the digital module. Each bit in this byte is assigned to a channel and returns information on
the validity of the digital value (0 = incorrect value).
Address space for the RQ 4x24VUC/2A CO ST digital output module:
The following figure shows the assignment of the address space for the RQ 4x24VUC/2A
CO ST with value status (Quality Information (QI)). The addresses for the value status are
only available if the value status is enabled.
Figure 2-1 Address space for the RQ 4x24VUC/2A CO ST digital output module
Section 6.1 Technical specifications
Correction / additions to the technical specifications:
●Switching capacity of the contacts (DC)
–Rated switching voltage (DC): 24 V
–With resistive load, max.: 2 A
–Thermal continuous current, max.: 2 A
●Switching capacity of the contacts (AC)
–Rated switching voltage (AC): 24 V
–With resistive load, max.: 0.5 A
–Thermal continuous current, max.: 0.5 A

General additions to the documentation
Product information on the documentation of the ET 200SP distributed I/O system
20 Product Information, 12/2014, A5E03799595-AL
DQ 4x24..230VAC/2A ST digital output module manual, Edition 02/2014
Section 3.1 Terminal assignment
Note
Power limitation
To limit power, each input voltage must have a fuse with a maximum rating of 8 A tripping
current. The fuse must be a quick
-acting microfuse.
Section 6.1 Technical specifications
Short-circuit protection: No; install a fuse with 8 A tripping current when using a type B1 BU
Overload protection: No; install a fuse with 8 A tripping current when using a type B1 BU
The fuse must be a quick-acting microfuse in each case.
AI 2xU/I 2-/4-wire HF analog input module manual, Edition 02/2014
Note
Changing parameter settings in runtime can cause the process values to freeze for the
duration of the parameter assignment for the module.
Manuals AI 2xU/I 2-/4-wire HF, Edition 02/2014; AI 4xRTD/TC 2-/3-/4-wire HF, Edition 02/2014;
AI 8xRTD/TC 2-wire HF, Edition 02/2014; AQ 2xU/I HF, Edition 02/2014
Note
The "Channel temporarily not available" diagnostics message is reported during a change to
the user calibration.
Other diagnostics messages must not be used to detect a change to the user
calibration.