Siemens RDD100 Series User manual

CB1B1420en_01 / 2013-03-07 Subject to alteration Siemens Building Technologies
s
Operating Instructions RDD100..
RDD100.. – the room thermostat that allows you to set the ideal room temperature at the time you want.
1. Display
Indicating that batteries need to be replaced
(only with battery-powered version)
Comfort mode
Economy mode
Frost protection (heating) is active
Display of room temperature, setpoint, etc.
F
Room temperature in degrees Fahrenheit
C
Room temperature in degrees Celsius
Button lock activated
Heating ON
Current room temperature
2. Change operating mode
3. Decrease value
4. Increase value
5. Battery holder
Do you want to change the operating mode?
!
The thermostat provides Comfort mode ,
Economy mode . Changeover between the
operating modes can be made manually by
pressing .
Comfort mode is the permanent (24 h) selection
of Comfort. Select this mode to maintain Comfort
temperature permanently. It is used during
occupancy periods, for example.
Economy mode is the permanent (24 h)
selection of Economy. Select this mode to
maintain the Economy temperature permanently.
It is used during non-occupancy periods, for
example at night.
Note:
Frost protection is a function always active in
the background. As soon the room temperature
falls below 5 ºC, the unit automatically activates
the heating .
Energy saving tips without sacrificing
comfort
•Use Economy mode for long periods of non-occupancy
Do you want to lock the buttons?
Press and hold for at least 7 seconds to
activate a button lock. Repeat to unlock.
The unit operates normally when the buttons are
locked, but no changes are possible while the
buttons are locked.

CB1B1420en_01/ 2013-03-07 Subject to alteration Siemens Building Technologies
Are your rooms too warm/too cold?
+
–
Press + or – to increase or decrease the room
temperature setpoint in increments of 0.5 °C /
1 °F. Proceed as follows:
•Press +or –to adjust the setpoint
temporarily.
Press to save the value or wait for the
program to exit automatically.
•To permanently modify the temperature
setpoints, use parameters P05 and P07.
To lock the setpoints, use parameters P06
and P08.
Does symbol appear on the display?
(Only with battery-powered version)
Symbol is displayed when the batteries are low.
Replace them with 2 new alkaline batteries type AAA.
Proceed as follows:
•Get 2 new alkaline batteries type AAA
•Remove the battery holder, then the batteries, insert
the new batteries and, within 1.5 minutes, replace the
battery holder
•Ensure the exhausted batteries are disposed of
correctly, in compliance with environmental
requirements
Do you want to change parameters?
+
–
If you want to change control parameters,
proceed as follows:
•Press +and – simultaneously for 5 seconds
•Release them and parameter "P02" is
displayed
•Press +or – to scroll to the parameter that
needs to be adjusted
•Press to select this parameter
•Press +or – to adjust the value
•Press to confirm and save the adjusted
value
•Select and modify other parameters
•The program automatically returns to the
normal screen after a timeout.
Parameter list
Parameter
no. Description Setting range (default)
P02 Selection of °C
or °F 1 = °C (default)
2 = °F
P03 Standard
temperature
display
1 = room temperature
(default)
2 = setpoint
P04 Temperature
sensor
calibration
-3…3 °C
Step 0.5 °C
(-6…6 °F, step 1 °F)
Default: 0 °C
P05 Comfort setpoint 5…35 °C, step 0.5 °C
(41…95 °F, step 1 °F)
Default: 20 °C, 68 °F
P06 Comfort setpoint
lock 0 = OFF (default)
1 = ON locked according
to setting in P05
P07 Economy
setpoint 5…35 °C, step 0.5 °C
(41…95 °F, step 1 °F)
Default: 16 °C, 61 °F
P08 Economy
setpoint lock 0 = OFF (default)
1 = ON locked according
to setting in P07
P09 Buzzer 0 = OFF
1 = ON (default)
P10 Show frost
protection icon 0 = OFF (default)
1 = ON
P21 Button scanning
rate for the
capacitive
buttons (touch
keys, RDD100.1
only)
Note: a shorter
scanning rate
means shorter
battery life.
0.2 = 0.25 s
0.5 = 0.5 s
1.0 = 1.0 s (default)
1.5 = 1.5 s
P22 Reload factory
settings 0 = OFF (default)
1 = Reload
P23 Software version
information No adjustment possible