Sigfox Sens’it 3 series User manual

SENS’IT 3 USER MANUAL
Table of contents
Table of contents ..................................................................................................................................... 1
SENS’IT 3 - 5 SENSORS, ONE BUTTON, SO MANY POSSIBI ITIES ............................................................ 1
DEVICE ACTIVATION ................................................................................................................................ 1
USER INSTRUCTIONS ............................................................................................................................... 1
AVAI AB E MODES .................................................................................................................................. 2
TECHNICA SPECIFICATIONS .................................................................................................................... 2
SENS’IT FOR DEVE OPERS ....................................................................................................................... 3
SENS’IT 3 - 5 SENSORS, ONE BUTTON, SO MANY POSSIBILITIES
Sens’it is a configurable multi-sensor device: you can adapt it to many use cases, and build your own
usage. The number of sensors it provides, along with its ability to communicate wherever there is
Sigfox coverage, open it to a wide array of possibilities.
DE ICE ACTI ATION
It only takes a few minutes to get started with your Sens’it:
1. Visit www.sensit.io and click on “Start with my Sens’it”.
2. Use the ID that is printed on the back of the Sens’it.
3. Make a long press (two seconds) on the button to change mode and send a message.
The main ED will turn light up in the color of the chosen mode (see below).
4. Wait until the ED blinks: this shows that data is being transmitted.
5. You can now access your sensit.io dashboard and see the transmitted data.
USER INSTRUCTIONS
The Sens’it is easy to configure:
1. Select the mode you want to use (see below).
2. Place the Sens’it on asset or in the location about which you want information and leave it.
…or press the Sens’it button twice to send data.
3. Keep track of your data on the online dashboard.
…or receive notifications when a threshold is passed.
The Sens’it button has a different action depending on how it is pressed:
-Indicate the current mode: one short press. The ED will blink in the current mode color.
-Change mode: one long press. The ED changes color depending on the active mode. You can
keep pressing the button and it will keep switching mode until you stop. Once a mode is
chosen, the Sens’it sends data.

-Send data with the current measurement: 2 short presses. This can be used to send an alert.
-Reset the Sens’it: 4 shorts presses (in Button mode only). The Sens’it returns to factory
settings.
A AILABLE MODES
The Sens’it can be configured in 6 different modes. Each mode has a specific color:
-Green: Temperature and Humidity mode. The Sens’it sends sensor data at a defined
frequency.
-Yellow: ight mode. The Sens’it either sends light sensor data at a defined frequency.
-Light blue: Door opening detection. The Sens’it is affixed to a door, and sends data every
time the door is being opened (through its magnetometer).
-Dark blue: Vibration detection. The Sens’it sends data every time the accelerometer has
detected a movement.
-Pink: Magnet mode. The Sens’it sends data every time a magnet is put near the right side of
the Sens’it.
-White: Button mode. The Sens’it sends data every time the button is pressed.
You can change mode by doing a long press on the button.
The sending frequency can be defined on the online app: every 10 minutes, every hour, every 6
hours, every 24 hours. You can also trigger an immediate data transmission by making two short
presses on the button.
By default, only one mode can be selected at a time.
TECHNICAL SPECIFICATIONS
RADIO CHARACTERISTICS
MECHANICA CHARACTERISTICS
-Dimensions (W x H x D): 52 mm x 82 mm x 15 mm
-Weight: 50 g
-Solid particle protection: IP54
ENVIRONMENTA CHARACTERISTICS
3 1
3 2
3 3
3 4
TX frequency
868.13 MHz
902.2 MHz
923.2 MHz
920.8 MHz
RX frequency
869.525 MHz
905.2 MHz
922.2 MHz
922.3 MHz
TX power
14 dBm
22 dBm
7 dBm
22 dBm
Sigfox Ready class
U0
U0
U1
U0

-Operating temperature: -10 °C to +55 °C
-Relative humidity: 30 % to 90 %
-Storage temperature: -20 °C to +75 °C
POWER SUPP Y CHARACTERISTICS
-Battery type: iPo
-Technical characteristics: 250 mAh, 3.7 V
-Recharge: 5 V, via USB
SENS’IT FOR DE ELOPERS
Sens’it introduces everyone to the possibilities of Sigfox through a configurable end-to-end solution.
With the Sens’it SDK, developers can use their Sens’it as a devkit, build their own firmware, have
access to the Sigfox Cloud… all that with Sigfox connectivity included!
earn more about the Sens’it SDK on www.sensit.io!