Sigfox Sens'it User manual

USER MANUAL
www.sensit.io
Sens’it

SUMMARY

SAFETY INSTRUCTIONS 4
I. CONTENT OF THE PACK 4
II. PRESENTATION 5
III. HOW TO START 8
IV. TECHNICAL SPECIFICATIONS 9
V. WARNING STATEMENTS 10
VI. CREDITS 11

4
SAFETY INSTRUCTIONS
* Before any use, please read carefully this manual and keep it for any
later use.
* Any use not in accordance with this manual will result the exclusion
of warranty and of the manufacturer’s liability.
* Use only parts and components coming from Sigfox and Sens’it.
* Place the Sens’it in a cool and dry area. For the withstood temperature
and humidity ranges, see the technical specications.
* Do not leave any electronic equipment on the top the Sens’it.
* Do not submerge Sens’it in liquids
* Do not place the magnet close to electronic devices, like PCs,
batteries, etc, they could be damaged, or information could be
deleted.
I. CONTENT OF THE PACK
YOUR SENS’IT PACK CONTENTS:
* 1 Sens’it
* 1 magnet
* 1 micro USB cable
* 1 velcro scratch
* 1 Sens’it user manual

5
II. PRESENTATION
Sens’it is a connected device whose objective is to
demonstrate capabilities of Sigfox network. It includes
several sensors that will measure data and send it to web and
mobile applications available on www.sensit.io
THE SENS’IT CAN BE CONFIGURED IN 6 DIFFERENT
MODES:
* Temperature and Humidity mode (LED blinks in green).
In this mode, the Sens’it will send sensors’ data at a dened
frequency (every 10min, hour, 6hours, day).
* Light mode (LED blinks in yellow). In this mode, the Sens’it
will either send light sensor data at a dened frequency or
will only send notication based on trigger.
* Door opening detection (LED blinks in light blue). In this
mode, the Sens’it will be xed on a door, and will send an
alert every time the door is being opened.
* Vibration detection (LED blinks in dark blue). In this mode,
the Sens’it will send a notication every time the movement
sensor has detected a movement.
* Magnet (LED blinks in Purple). The Sens’it will send a
message every time the magnet is put near the right side of
the Sens’it.
* Button – Only (Secondary LED blinks in White). Sens’it will
send a message every time the button has been pressed.

6
HOW TO CHANGE MODES AND SEND MESSAGES:
* One long press on the central button will make the Sens’it
change mode.
* On double press and the Sens’it will directly send a message.
* On short press and the LED will blinks in the current mode
color.
CHARGING
* To recharge the Sens’it, a micro USB cable is needed.
* Once plugged, the secondary RED LED will turn on. It turns
o when the battery is completed charged.
* The main LED blinks twice in RED to warn user of an empty
battery.
WEB & MOBILE APP
* Sens’it data is available on www.sensit.io website on
Desktop and Mobile. The application allows monitor data but
also to congure email, sms or web notications depending
on the current mode of the Sensit.
* iPhone and Android apps are also available in app stores.
* An API for developers is available on api.sensit.io

7
Temperature
& humidity
Light Door opening
detection
Movement
or vibration
Magnet Alerting
Sens’it

8
Visit www.sensit.io
and click on “Start
with your Sens’it”
Use the ID printed
at the back of your
Sens’it
Long press on the
main central button
Main LED will turn
green to show your
Sens’it is in the
temperature mode
Wait until the
LED blinks green,
showing a signal is
being sent
Data transmitted are
available on the web
app dashboard
1
4
2
5
3
6
ID : D4523
=19°C
III. HOW TO START

9
IV. TECHNICAL SPECIFICATIONS
TECHNICAL CHARACTERISTICS
Includes a 250mAh LiPo battery
Dimensions (W x H x D): 48 mm x 85 mm x 14 mm
Radio characteristics
Sens’it is Sigfox Ready Class 0
TRANSMISSION AND RECEPTION DETAILS
(Depending on local Radio Conguration)
Frequencies Used: 868-870 MHz, 902-905Mhz or 920-922Mhz
Emission power: 14 dBm or 22dBm
ENVIRONMENTAL CHARACTERISTICS
Temperature range: -10°C to +50°C
Maximum relative humidity: 90 %
THE SENS’IT INCLUDES
SEVERAL SENSORS:
* Temperature
* Humidity
* Movement (3-axis
accelerometer)
* Magnetometer
* Light
IT ALSO INCLUDES
* A central button to control
the device
* A Reed-switch that goes
with the magnet.
* 3 LEDs

10
V. WARNING STATEMENTS
1. FCC:
This device complies with Part 15 of the FCC Rules.
Operation is subject tothe following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
• The radiated output power of the device is far below the FCC radio
frequency exposure limits. Nevertheless, the device shall be used in
such a manner that the potential for human contact during normal
operation is minimized.
• Changes or modications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.

11
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
2. IC
This device complies with Part 15 of the FCC Rules and with Industry
Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(1) this device must accept any interference received, including
interference that may cause undesired operation.
3. CE
Do not throw away Sens’it in the normal household trash; it must be
disposed properly in the same way as other electronic equipment
following ocial procedures.
VI. CREDITS
Sens’it is owned by Sigfox.
Sens’it development has been in partnership with Axible Technologies.
Sens’it is assembled in France.
In partnership with Texas Instruments.

Do not throw away Sens’it in the normal household trash; it must be disposed
properly in the same way as other electronic equipment following ocial procedures.
Contact: c[email protected]