Silicon Laboratories SiTCXO1-EVB User manual

UG364: SiTCXO1-EVB Evaluation Board
User's Guide
The Silicon Labs SiTCXO1-EVB (kit) is used to help evaluate Silicon Labs Jitter Attenu-
ator and Network Synchronization products for Stratum 3/3E, IEEE 1588 and G.8262
SyncE applications. This board is often used with the Si5348 network synchronizer
clock as the reference input. This board can come with an option of one of two Rakon
TCXOs. U1, option 1 is Rakon's E6518LF 5 mm x 7 mm part (pictured below) and U2,
option2 is Rakon's smaller RPT5032A 3.2 mm x 5 mm part.
EVB FEATURES:
• Dual Footprint capable of two TCXO sizes.
• Power supply filtering
•Simple single ended output
silabs.com | Building a more connected world. Rev. 0.1

1. Quick Start
1. Connect power 3.3V to J1, and note that start-up current could be on the order of 7-8 mA.
2. Connect SiOCXO1-EB output, J2, to the Si5348 REF clock input using the short SMA cable provided with the EVB kit.
UG364: SiTCXO1-EVB Evaluation Board User's Guide
Quick Start
silabs.com | Building a more connected world. Rev. 0.1 | 2

2. Top Layer View of Board
Figure 2.1. Top Layer View of Board
UG364: SiTCXO1-EVB Evaluation Board User's Guide
Top Layer View of Board
silabs.com | Building a more connected world. Rev. 0.1 | 3

3. Functional Description
The SiTCXO1-EB is used in conjunction with Silicon Labs precision timing devices to facilitate characterization. The SiTCXO1-EB was
designed to maximize output termination configurations as well as optional control voltage terminations. Resistors and capacitors are
0603, which makes it simple to remove and add various values. The SiTCXO1-EB bill of materials and PCB layouts are in Section
7. Bill of Materials and Section 6. Schematic.
The SiTCXO1-EB is intended to be a general use board for a 6-pin TCXO with 5.0 mm x 3.2 mm nominal package size, such as the
Rakon P/N RPT5032A. It can also be used with the 6-pin TCXO with 5.0 mm x 7 mm nominal package size, such as the Rakon P/N
E6518LF 12.8 MHz pictured below. See 6. Schematic for example measurements carried out using this TCXO.
Figure 3.1. SiTCXO1-EB Shown Populated with a TCXO
3.1 Power Supply
The power supply voltage and current requirements are listed in the manufacturers data sheet. A 3.3 V ±5% supply is required. Also,
note the TCXO initial current can be on the order of 7mA. Power supply filtering has been added to the evaluation board to minimize
spurious response.
3.2 Output Termination
In most applications simple R C termination is used, as seen with R3 and C4 in Figure 6.1 SiTCXO1-EB Schematic on page 7. This
is a resistor to optimize impedance matching and a capacitor to block dc. Modifications can be made as required.
UG364: SiTCXO1-EVB Evaluation Board User's Guide
Functional Description
silabs.com | Building a more connected world. Rev. 0.1 | 4

4. Configuring the SiTCXO-EB
SiTCXO1-EB
Power Supply
Ref Input
Si5348-EVB
Frequency Counter
or other MTIE TDEV Instrument
Figure 4.1. SiTCXO1-EB Configured with Si5348 EVB
The connection between the SiTCXO-EB and Si5348 EVB should be kept as short as possible. It is recommended to use a UPS Power
Supply back-up for long term testing.
UG364: SiTCXO1-EVB Evaluation Board User's Guide
Configuring the SiTCXO-EB
silabs.com | Building a more connected world. Rev. 0.1 | 5

5. SiTCXO1-EB Functionality Test
1. Connect power to J1 (3.3 V).
2. Connect SiTCXO1-EB Output, J2, to an oscilloscope (terminate into 50 Ω).
3. Verify that the red LED is illuminated, the current draw matches closely to the specs, and the output matches the TCXO’s data
sheet.
UG364: SiTCXO1-EVB Evaluation Board User's Guide
SiTCXO1-EB Functionality Test
silabs.com | Building a more connected world. Rev. 0.1 | 6

6. Schematic
Figure 6.1. SiTCXO1-EB Schematic
UG364: SiTCXO1-EVB Evaluation Board User's Guide
Schematic
silabs.com | Building a more connected world. Rev. 0.1 | 7

7. Bill of Materials
Table 7.1. Bill of Materials
Qty Ref Value Rating Voltage Tol Type PCB Footprint Mfr PN Mfr
1 C1 10 µF 10 V ±10% TANT C3216 TA010TCM106KA Venkel
1 C2, C4 0.1 µF 10 V ±10% X7R C0603|C0603L C0603X7R100-104K Venkel
1 C3 100 pF 50 V ±20% C0G C0603 C0603C0G500-101M Venkel
1 C5 10 pF 50 V ±10% C0G C0603 C0603C0G500-100K Venkel
1 D1 Green 20 mA 3.4 V
SMT,
Chip
LED
LED-HSMX-C170 HSMQ-C170
Avago
Technolo-
gies
1 J1 CONN
TRBLK 2
TERM
BLK CONN-1X2-TB 1729018 PHOENIX CONTACT
1 J2 SMA SMA SMA-EDGE-3 142-0701-801
Johnson
Compo-
nents
1 R3 39.0 Ω 1/10 W ±1% Thick
Film R0603|R0603L ERJ-3EKF39R0V Panasonic
1 R4 17.4 kΩ 1/16 W ±1% Thick
Film R0603 CR0603-16W-1742F Venkel
1 U1 E6518LF Stratum
33.3 TCXO OSC6N5X7-E6518LF E6518LF Rakon
Not Installed Components
2 R1, R2 1 k 1/10 W ±1% Thick
Film R0603 CR0603-10W-1001F Venkel
2TP1,
TP2 Blue Loop TESTPOINT 151-205-RC Kobiconn
1 U2 RPT5032A TCXO OSC6N3.2X5P0.8-
RPT5032A RPT5032A Rakon
UG364: SiTCXO1-EVB Evaluation Board User's Guide
Bill of Materials
silabs.com | Building a more connected world. Rev. 0.1 | 8

8. Layout
Figure 8.1. Primary Silkscreen
Figure 8.2. Primary Solder Mask
UG364: SiTCXO1-EVB Evaluation Board User's Guide
Layout
silabs.com | Building a more connected world. Rev. 0.1 | 9

Figure 8.3. Primary Side
Figure 8.4. Secondary Side
UG364: SiTCXO1-EVB Evaluation Board User's Guide
Layout
silabs.com | Building a more connected world. Rev. 0.1 | 10

Figure 8.5. Secondary Solder Mask
Figure 8.6. Primary Solder Paste
UG364: SiTCXO1-EVB Evaluation Board User's Guide
Layout
silabs.com | Building a more connected world. Rev. 0.1 | 11

http://www.silabs.com
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
USA
ClockBuilder Pro
One-click access to Timing tools,
documentation, software, source
code libraries & more. Available for
Windows and iOS (CBGo only).
www.silabs.com/CBPro
Timing Portfolio
www.silabs.com/timing SW/HW
www.silabs.com/CBPro Quality www.silabs.com/quality Support and Community community.silabs.com
Disclaimer
Silicon Labs intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or
intending to use the Silicon Labs products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "Typical"
parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Labs reserves the right to make changes
without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included
information. Silicon Labs shall have no liability for the consequences of use of the information supplied herein. This document does not imply or express copyright licenses granted
hereunder to design or fabricate any integrated circuits. The products are not designed or authorized to be used within any Life Support System without the specific written consent of
Silicon Labs. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant
personal injury or death. Silicon Labs products are not designed or authorized for military applications. Silicon Labs products shall under no circumstances be used in weapons of mass
destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons.
Trademark Information
Silicon Laboratories Inc.® , Silicon Laboratories®, Silicon Labs®, SiLabs® and the Silicon Labs logo®, Bluegiga®, Bluegiga Logo®, Clockbuilder®, CMEMS®, DSPLL®, EFM®,
EFM32®, EFR, Ember®, Energy Micro, Energy Micro logo and combinations thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZRadio®, EZRadioPRO®,
Gecko®, ISOmodem®, Micrium, Precision32®, ProSLIC®, Simplicity Studio®, SiPHY®, Telegesis, the Telegesis Logo®, USBXpress®, Zentri, Z-Wave, and others are trademarks or
registered trademarks of Silicon Labs. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited.
All other products or brand names mentioned herein are trademarks of their respective holders.