Silk'n GoBrush Mist User manual

ID: #05007
m
y
h
a
n
s
e
c
o
n
t
r
o
l
.
c
o
m
M
A
N
U
A
L
D
E
V
E
L
O
P
E
D
I
N
G
E
R
M
A
N
Y
User-friendly
Manual

LOCK

4
EN
Contents
1. Package contents/device parts_____________5
2. Technologies _____________________________5
3. General information ______________________6
3.1 Reading and storing the user manual ________________________ 6
3.2 Explanation of symbols___________________________________ 6
4. Safety ___________________________________7
4.1 Proper use ____________________________________________ 7
4.2 Safety instructions ______________________________________ 7
5. Checking the steam brush straightener and
package contents_________________________12
6. Operation________________________________13
6.1 Before straightening_____________________________________ 13
6.2 Filling the water tank ____________________________________ 13
6.3 Switching on/o and selecting a temperature _________________ 14
6.4 Straightening hair _______________________________________ 14
7. Cleaning _________________________________16
8. Storage __________________________________17
9. Troubleshooting__________________________18
10. Technical data____________________________19
11. Disposal _________________________________19
11.1 Disposing of the packaging ________________________________ 19
11.2 Disposing of the steam brush straightener ___________________ 19
12. Warranty ________________________________20
13. Customer service ________________________20

EN
5
1. Package contents/device parts
1Heating plate (including brush), 2×
2Hanging loop
3Plate lock switch
4Steam nozzle
5Fill bottle
6Heat-resistant mat
7Water tank
8Rubber closure
9Tank lock switch
10 Display
11 Steam button
12 Control button
2.Technologies
3D Smoothing Technology consists of:
• Steam technology: adds moisture during the straightening
process, giving you sleek hair without over-drying it. Promotes
shine, less frizz, less heat damage, and safe use.
• Tourmaline coated plates: allow the hair to glide through
the steam brush straightener smoothly, without snags or
damage and heat evenly for faster straightening. Produce 20
times more moisture-locking ions than any other type of plate.
• Ionic technology: produces a stream of negative ions which
reduce the drying time significantly and eliminate frizz for a
smooth, shiny, healthy looking finish.
PTC (Positive Temperature Coecient) heating:
generates fast and energy ecient heat transfer; enables the
device to cool down quickly to prevent overheating and ensures a
higher level of safety.

6
EN
3.General information
3.1 Reading and storing the user manual
This user manual accompanies this GoBrush Mist
(hereafter referred to as the “steam brush
straightener”), and contains important information
on setup and handling.
Before using the steam brush straightener, read
the user manual carefully. This particularly applies to the safety
instructions. Failure to do so may result in personal injury or
damage to the steam brush straightener. The user manual is based
on the standards and rules in force in the European Union. When
abroad, you must also observe country-specific guidelines and
laws. Store the user manual for further use. Make sure to include
this user manual when passing the steam brush straightener on to
third parties.
3.2 Explanation of symbols
The following symbols and signal words are used in this user
manual, on the steam brush straightener or on the packaging.
WARNING!
This signal symbol/word designates a hazard with moderate risk,
which may result in death or severe injury if not avoided.
NOTICE!
This signal word warns of possible damage to property.
This signal symbol provides you with useful
additional information on handling and use.
Declaration of Conformity: Products labelled with
this symbol meet all applicable provisions of the
European Economic Area.
The symbol indicates that the product is of CLASS II
(double insulated) construction. It does not require a
safety connection to electrical earth (ground).

EN
7
Do not use the steam brush straightener in the
vicinity of bathtubs, showers, washbasins or other
vessels containing water.
4.Safety
4.1 Proper use
The steam brush straightener is exclusively designed for
straightening human hair only. It is only intended for private use
and not suitable for commercial purposes.
Only use the steam brush straightener as described in this user
manual. Any other use is considered improper and may result in
damage to property or persons. The manufacturer or vendor
cannot be held liable for damages or injury incurred through
improper or incorrect use.
4.2 Safety instructions
WARNING! RISK OF ELECTRIC SHOCK!
• Only connect the steam brush straightener
if the line voltage of the socket corresponds
to the data on the rating plate.
• Only connect the steam brush straightener
to an easily accessible socket so that you can
quickly disconnect it from the mains supply
in the event of a problem.
• Do not use the steam brush straightener
if it is damaged or if the mains cord or
plug is defective. If the mains cord of the
steam brush straightener is damaged, the
manufacturer or customer service must
replace it to avoid risks.

8
EN
• Do not open the housing; instead, have
a qualified professional perform repairs.
Contact the customer service team for this.
Liability and warranty claims are waived
in the event of repairs performed by the
user, improper connection or incorrect
operation.
• Only parts that comply with the original
device data may be used for repairs. This
steam brush straightener contains electrical
and mechanical parts which are essential
for providing protection against sources of
danger.
• Keep the steam brush straightener away
from water! Do not use the steam brush
straightener near or over water contained
in baths, washbasins, sinks etc. When used
in a bathroom, unplug the steam brush
straightener after use since the proximity of
water presents a risk, even when the steam
brush straightener is switched o.
• Do not immerse the steam brush
straightener or the mains cord in water or
other liquids. Do not place the steam brush
straightener such that there is a risk of it
falling into a tub or sink.
• Never reach to retrieve an electrical device

EN
9
if it has fallen into water. In such a case
immediately disconnect the mains plug.
• Always switch the steam brush straightener
o and unplug it when you are not using it,
when you intend to clean it, or in the event
of a malfunction.
• Never touch the mains plug with wet or
damp hands.
• For additional protection, the installation
of a residual current device (RCD) having
a rated residual operating current not
exceeding 30 mA is advisable in the
electrical circuit supplying the bathroom.
Ask your installer for advice.
• Do not use an extension cord with the
steam brush straightener.
• Never insert any objects into the housing.
• Do not pull the mains plug out of the socket
by the cord; instead, always pull it out by the
plug itself. Never move, pull, or carry the
steam brush straightener by its mains cord.
• Keep the steam brush straightener and
mains cord away from open flames and hot
surfaces.
• Lay the mains cord so that it does not pose
a tripping hazard.
• Do not kink the mains cord or wrap it

10
EN
around the steam brush straightener. Do
not lay the mains cord over sharp edges.
• Never attempt to remove dust or foreign
objects from inside the steam brush
straightener using a pointed object.
WARNING! DANGER FOR
CHILDREN AND PERSONS WITH
IMPAIRED CAPACITIES, OR LACK OF
EXPERIENCE AND KNOWLEDGE.
• The steam brush straightener is not
intended for use by persons (including
children) with reduced physical, sensory or
mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of
the steam brush straightener by a person
responsible for their safety. Children must
not play with the steam brush straightener.
Cleaning and user maintenance must not be
performed by unsupervised children.
• Keep children under the age of eight away
from the steam brush straightener and
mains cord.
• Make sure that children do not play with the
plastic wrapping. They may get caught in it
when playing and suocate.

EN
11
WARNING! RISK OF INJURY!
• The steam brush straightener heats up and
emits hot steam during use. Always hold it
by its handle when it is hot.
• Never leave the steam brush straightener
unattended while it is plugged in.
• Do not use outdoors or operate where
aerosol products are being used or where
oxygen is being administered.
• Always switch the steam brush straightener
o before putting it down, even if it is only
for a moment.
• Do not touch the hot surfaces of the steam
brush straightener. Always allow the steam
brush straightener to cool down before
storing or cleaning.
NOTICE! RISK OF DAMAGE!
• Place the steam brush straightener on an
easily accessible, level, dry, heat-resistant and
suciently stable surface. Do not place the
steam brush straightener on the edge of the
surface.
• Ensure that the mains cord does not come
into contact with hot parts.
• Never fill the housing of the steam brush
straightener with liquid. The only exception

12
EN
is filling the water tank with water for the
steam feature.
• Stop using the steam brush straightener if its
plastic parts exhibit cracks or breaks or are
deformed. Only replace damaged parts with
corresponding original spare parts.
• Do not operate the steam brush
straightener if it has been dropped or is
damaged in any way. Have the steam brush
straightener checked and/or repaired by
qualified technicians if necessary.
5.Checking the steam brush straightener
and package contents
NOTICE! RISK OF DAMAGE!
• If you are not cautious when opening
the packaging with a sharp knife or other
pointed object, you may quickly damage the
steam brush straightener. Be very careful
when opening it.
1. Take the steam brush straightener out of the packaging.
2. Check to make sure that all parts are included (see Fig. A).
3. Check whether the steam brush straightener or individual parts
are damaged. If this is the case, do not use the steam brush
straightener. Contact our customer service.

EN
13
6.Operation
• Clean all parts of the steam brush straightener before
first use as described in the chapter “Cleaning”.
• Before using the steam brush straightener for the first
time, switch it on for a few minutes and set it to the
highest temperature. As a result of the manufacturing
process, you may notice a slight odour. This is normal
and only occurs during first use. Ensure that the room
is well ventilated.
6.1 Before straightening
• The hair should be clean, dry and free of styling products
(except special products that promote hair straightening).
• Thoroughly comb the hair so that there are no knots in it.
• Separate your hair into horizontal sections. Each section should
be around the width and thickness of a heating plate 1.
Pin or clip the sections you are not working on out of the way.
6.2 Filling the water tank
The optional steam feature ensures gentle hair straightening for
silkier and shinier hair. Fill the water tank only when you intend to
use the steam feature.
Use only distilled water to fill the water tank. Otherwise,
limescale may form inside the steam brush straightener
and shorten the product lifespan.
1. Fill the fill bottle 5with distilled water and remove the small
cap at the tip.
2. Open the rubber closure 8on the water tank 7.
3. Guide the tip of the fill bottle into the opening on the water tank.
4. Gently squeeze the fill bottle so that water runs into the water
tank.
5. When the water tank is full (approx. 12 ml), remove the fill
bottle from the water tank and replace the rubber closure to
close the opening.
6. Wipe dry any spilled water on the steam brush straightener
with a soft cloth.
The steam brush straightener is now ready for the steam feature.

14
EN
6.3 Switching on/o and selecting a temperature
1. Connect the mains plug to an easily accessible socket. The
message “OFF” will show on the display 10 once the steam
brush straightener is connected to power.
2. Press and hold the control button 12 to switch on the steam
brush straightener. On the display, the progress bars ( ) are
flashing until the steam brush straightener has reached the
default operating temperature (120 °C) (see Fig. B).
3. To select another operating temperature, press the control
button repeatedly to cycle through the temperature settings
and select a desired one. You can select a temperature
setting between 120 °C and 230 °C. Each press of the button
will increase the temperature setting by 5 °C. Once a new
temperature setting is selected, the progress bars ( ) will
flash until the steam brush straightener has reached the newly
selected operating temperature.
Below are recommended settings. If you are unsure, start
with a lower temperature and increase the temperature as
necessary.
Temperature Hair type
120 °C–155 °C Fine, damaged or chemically treated
160 °C–195 °C Normal
200 °C–230 °C Thick, curly, not chemically treated
4. To switch o the steam brush straightener, press and hold the
control button until the message “OFF” shows on the display.
For safety purposes, the steam brush straightener will automat-
ically shut down after 1 hour (Auto Shut O Protection) in case
you forget to switch it o.
6.4 Straightening hair
WARNING! RISK OF INJURY!
• Ensure that the heating plates do not touch
your scalp.

EN
15
• Never touch the heating plates and the
upper part of the steam brush straightener
during use.
• Always pull the steam brush straightener
through the hair. Never stay at one position
for too long. You may singe your hair!
1. Prepare the hair as described in the chapter “Before
straightening”.
2. If you intend to use the steam feature, fill the water tank as
described in the chapter “Filling the water tank”.
3. Switch on the steam brush straightener and select a desired
operating temperature (see chapter “Switching on/o and
selecting a temperature”).
4. If the heating plates 1are closed, slide the plate lock switch 3
to the unlock position ( ) to open them.
5. If you intend to use the steam feature, press the steam button 11
once. The steam icon ( ) will show on the display 10 .
6. Take a hair section and pull it taut by holding its end tightly
between your index and middle finger of the hand that is NOT
holding the steam brush straightener.
7. Clamp the hair section near the root by pressing the heating
plates 1together.
If the steam feature is used, steam will be emitted from the
steam nozzle 4while the heating plates are pressed together.
The steam icon ( ) flashes while steam is emitted. A full
water tank (approx. 12 ml) provides about 15 minutes of
steam styling.
8. Glide the steam brush straightener downwards from the root
to the tip through the heating plates (see Fig. C).
Control the speed for better results in a single glide. Next are
recommendations.

16
EN
Hair type Speed
Fine Around 5–8 cm per second
Normal Around 5 cm per second
Thick Around 2–3 cm per second
9. Proceed in the same way for every hair section.
While sectioning the hair, you can let the steam brush
straightener rest on the heat-resistant mat 6included.
10. When done, press and hold the control button 12 until the
message “OFF” shows on the display.
11. Unplug the steam brush straightener and allow it to cool
down completely on the heat-resistant mat. The steam brush
straightener is only completely without power when the mains
plug is pulled out of the socket.
12. Empty the water tank 7if there is still water in it after
use. To do so, remove the water tank from the steam brush
straightener by pulling the water tank out while pushing the
tank lock switch 9towards the lock icon (LOCK). Then open
the rubber closure 8on the water tank to empty the water.
Close the rubber closure and replace the water tank to the
steam brush straightener when done.
Locking the temperature: Press and hold the steam
button 11 until the lock icon ( ) shows on the display to
lock the temperature setting. To deactivate this feature,
press and hold the steam button until the lock icon is
turned o.
7. Cleaning
WARNING! RISK OF INJURY!
• Always unplug and let the steam brush
straightener completely cool down before
cleaning.

EN
17
NOTICE! RISK OF DAMAGE!
• Never immerse the steam brush
straightener in water or other liquids.
Make sure that no water or other liquids
penetrate the housing. The only exception
is filling the water tank with water for the
steam feature.
• Do not use any aggressive cleaners, brushes
with metal or nylon bristles, or sharp or
metallic cleaning utensils such as knives, hard
scrapers and the like.
Wipe the steam brush straightener with a damp cloth. Allow it to
dry completely.
8.Storage
• All parts must be completely dry and cooled down before
being stored.
• Do not wind the mains cord round the steam brush
straightener.
• Empty the water tank 7before storage.
• For space-saving storage, close the heating plates 1by
pressing them together and pushing the plate lock switch 3
to the close position ( ).
• Wrap the heat-resistant mat 6around the steam brush
straightener and secure with the attached fasteners for extra
storage protection; or hang the steam brush straightener up
on the hanging loop 2.
• Keep the steam brush straightener away from children.
• Store the steam brush straightener in a clean and dry place.

18
EN
9. Troubleshooting
Some problems may be caused by minor faults that you can fix
yourself. To do so, follow the instructions in the following table.
If it is still not possible to resolve the problem, contact customer
service. Do not repair the steam brush straightener yourself.
Fault Possible cause and solution
The steam brush
straightener is not
working.
The mains plug has not been inserted into a
socket. Connect the mains plug to a socket.
The hair does not
straighten. • The hair is not clean, dry, or free of
hair products (except hair straightening
products).
• The heating plates are not clean.
• The set operating temperature is too
low. Select a higher temperature.
The hair is singed. The set operating temperature is too high.
Select a lower temperature. Never stay at a
position on the hair for too long.
There is no steam
coming out from
the steam nozzle.
• If the water tank is not full, tilt the steam
brush straightener so that water flows
into the device for the steam feature.
• The water tank may be blocked (e.g. by
limescale).

EN
19
10. Technical data
Model: A5887
Mains voltage: 110–240 V~, 50/60 Hz
Power rating: 65 W
Protection class: II
Weight: 450 g
Dimensions (L × W × H): 300 × 55 × 44 mm
Heating plate dimensions (L × W): 36.7 × 90 mm
Heat-up time: 40 sec. to reach 120 °C
Water tank capacity: 12 ml
Temperature range: 120–230 °C
11. Disposal
11.1 Disposing of the packaging
Sort the packaging before you dispose of it. Dispose
of paperboard and cardboard with the recycled
paper service and wrappings with the appropriate
collection service.
11.2 Disposing of the steam brush straightener
(Applicable in the European Union and other European countries
with separate collection systems of recyclable materials)
Old appliances may not be disposed of in the
household waste!
Should the steam brush straightener no longer be
capable of being used at some point in time, dispose
of it in accordance with the regulations in
force in your city or county. This ensures that old
appliances are recycled in a professional manner and also rules
out negative consequences for the environment. For this reason,
electrical equipment is marked with the symbol shown here.