Philips HP4698 User manual

Geometricks 10 in 1
HP4698

2

3
1

4

HP4698
ENGLISH 6
 15
 24
 32
 40
 48
 57
 66
 74
 82
 91
 100
 110
 119
 127
 135

6
Introduction
With the new Salon Multistylist 10-in-1 you can create a unique look for
everyoccasion.The new 10-in-1 offers unlimited creativity and versatility
in hairstyling!
You can visit our website at wwww.philips.com for more information
about this product or any other Philips product.
General Description (Fig. 1)
ABrush
BSmall curling attachment
CSpiral
DLarge curling attachment
EZig-zag attachment
FTriangle attachment
GCrimping/straightening attachment
HCrimping/straightening plates
IHandle
JStorage pouch
KHair clips
Important
Read these instructions for use carefully before using the appliance and
save them for future reference.
Check if the voltage indicated on the appliance corresponds to the
local mains voltage before you connect the appliance.
Check the condition of the mains cord regularly. Do not use the
appliance if the plug, the cord or the appliance itself is damaged.
If the mains cord is damaged, it must be replaced by Philips, a
service centre authorised by Philips or similarly qualied persons in
order to avoid a hazard.
Keep this appliance away from water! Do not use this product near
or over water contained in baths, washbasins, sinks etc.When used
in a bathroom, unplug the appliance after use since the proximity of
water presents a risk.
,
,
,
,
ENGLISH

For additional protection, we advise you to install a residual
current device (RCD) with a rated residual operating current not
exceeding 30mA in the electrical circuit supplying the bathroom.
Ask your installer for advice.
Do not connect the handle to the mains without attaching an
attachment rst. Make sure the attachment is properly xed to the
handle before you put the plug in the wall socket.
Keep the attachments clean and free of dust, dirt, styling spray and
gel. Never use the appliance in combination with styling mousse,
styling spray, gel etc.
The attachments have a ceramic coating.This coating will wear
in the course of time.When this happens, the appliance will still
function normally.
The ceramic-coated parts of the attachments will become hot
during use. Prevent contact with the skin. Do not allow the mains
cord to touch any hot parts.
Always return the appliance to a service centre authorised by
Philips for examination or repair. Repair by unqualied people could
cause an extremely hazardous situation for the user.
Keep the appliance out of the reach of children.
Only use the appliance on dry or damp hair.
Always unplug the appliance after use.
Wait until the appliance has cooled down before storing it.
Do not wind the mains cord round the appliance.
Preparing for use
Before you start styling, comb or brush the hair so that it is
untangled and smooth.
Connecting the attachments
1 Insert one of the attachments into the handle. Make sure that the
stand is pointing downwards. (Fig. 2)
2 Turn the locking ring on the handle to the right until the bold
arrow on the locking ring is in line with the arrow on the handle.
The attachment is now securely xed to the handle. (Fig. 3)
,
,
,
,
,
,
,
,
,
,
,
,
ENGLISH 7

Follow this procedure for all attachments.To detach the
attachments, turn the locking ring to the left and pull the
attachment out of the handle.
Unplug the appliance when you remove an attachment after or during
styling.Avoid touching the metal and ceramic parts of the attachment,
as they are hot.

With the Salon Multistylist 10-in-1 you can create tight curls, large curls,
waves, ringlets, crimps, zig-zag curls, triangular curls and a sleek look.
1 After having connected the attachment to the handle, place the
appliance on the stand of the attachment and put the mains plug
in the wall socket.The pilot light goes on and the appliance starts
heating up. (Fig. 4)
2 Start styling when the ready dot on the attachment changes colour.
(Fig. 5)
3 When using one of the curling attachments or the brush, always
make sure the end of the lock is wound in the required direction.
4 How long you have to keep the styler in your hair depends on the
thickness of your hair. If you have ne hair, 5 seconds will be long
enough for a good result. Leave the styler in your hair longer (max.
10 seconds) if your hair is thicker.
Large or tight curls
1 Connect the large or small curling attachment to the handle. Make
sure that the stand is pointing downwards.
2 Take a lock of hair, open the clip by pressing the lever and place the
lock between the barrel and the clip. (Fig. 6)
3 Release the lever and slide the barrel to the end of the lock.Then
wind the lock round the barrel.
Make sure that the end of the lock is wound in the required direction.
,
ENGLISH8

4 Open the clip after 5 to 10 seconds and remove the barrel from
the hair. Let the curls cool down before combing, brushing or
nger-combing the hair into its nal style.
You can comb the curls with your ngers to add volume.
Waves
Prevent the brush from getting tangled in the hair in the following way:
Do not put too much hair in one lock.
Do not wind a lock of hair more than twice round the brush.
When unwinding a lock of hair, make sure that you hold the brush
away from the underlying hair.
1 Connect the small curling attachment to the handle and slide the
brush onto the curling attachment.
2 Take a lock of hair and wind it round the brush. (Fig. 7)
3 Remove the brush from your hair after 5 to 10 seconds. Let the
waves cool down before combing, brushing or nger-combing the
hair into its nal style.`
Ringlets
1 Connect the large curling attachment to the handle and slide the
spiral onto the curling attachment.
2 Take a lock of hair, open the clip by pressing the lever and place the
lock between the barrel and the clip. (Fig. 8)
3 Release the lever and slide the barrel to the end of the lock.Then
wind the lock round the barrel following the spiral prole. Make
sure that the end of the lock is wound in the required direction.
4 Open the clip after 5 to 10 seconds and remove the barrel from
the hair. Let the ringlets cool down before combing, brushing or
nger-combing the hair into its nal style.

1 Connect the triangle attachment to the handle. Make sure that the
stand is pointing downwards.
,
-
-
-
ENGLISH 9

2 Take a lock of hair, open the clip by pressing the lever and place the
lock between the barrel and the clip. (Fig. 9)
3 Release the lever and slide the barrel to the end of the lock.Then
wind the lock round the barrel.
Make sure that the end of the lock is wound in the required direction.
4 Open the clip after 5 to 10 seconds and remove the barrel from
the hair. Let the triangular curls cool down before combing,
brushing or nger-combing the hair into its nal style.
Zig-zag curls
1 Connect the zig-zag attachment to the handle. Make sure that the
stand is pointing downwards.
2 Take a lock of hair, open the clip by pressing the lever and place the
lock between the barrel and the clip. (Fig. 10)
Make sure that the end of the lock is wound in the required direction.
3 Open the clip after 5 to 10 seconds and remove the barrel from
the hair. Let the zig-zag curls cool down before combing, brushing
or nger-combing the hair into its nal style.
Crimps
1 Connect the crimping/straightening attachment with crimping
plates to the handle. (Fig. 11)
2 Take a lock of hair (max. 5 to 6 cm wide), open the attachment
by pressing the lever and place the lock between the plates of the
crimping/straightening attachment. Start crimping at the roots.
(Fig. 12)
3 Keep the plates locked for 5 to 10 seconds.
4 Open the attachment by pressing the lever and place a lower
section of the same lock of hair between the plates. Make sure
there is an overlap. Repeat this process until you have reached the
end of the lock.
ENGLISH10