SilverAqua SV1 User manual

U S E A N D M A I N T E N A N C E M A N U A L
E l e c t r o l y t i c g e n e r a t o r f o r t h e p r o d u c t i o n o f c o l l o i d a l
s i l v e r - S i l v e r a q u a S V 1 m o d e l
Thank you for your purchase of our electrolytic generator for the production of colloidal silver: SilverAqua
Model SV1. (hereinafter referred to as SV1)
The device is made of high-quality materials and will produce for you and your family all the colloidal silver
you need for years to come.
SV1 is a professional device designed after years of research. It works with a specific frequency capable to
produce particles up to 5 nm. The pole reverser guarantees maximum cleanliness of the large silver bars.
SV1 can automatically control current and voltage to make the water conductive without having to heat it,
up to maximum of 35 PPM allowing you to produce five liters of colloidal silver in just nine hours (12/16
PPM).
DLGSHOP di Del Grosso Stefano
Headquarters: Via Chiantigiana, 36 - 52025 Montevarchi (AR) Italy
Phone: [phone]
E-mail: [e-mail]
Website: www.silveraqua.it

Manual – Silveraqua SV1 model
Page/2
Summary
Section 1 ....................................................................................................................................3
DECLARATION OF CONFORMITY ..................................................................................................... 4
MANUFACTURER'S DATA ................................................................................................................ 4
AUTHORIZED SERVICE ..................................................................................................................... 4
PRESENTATION OF THIS MANUAL.................................................................................................... 5
Conventions............................................................................................................................................... 6
Pictograms ................................................................................................................................................. 6
ATTACHED DOCUMENTATION ......................................................................................................... 7
Section 2 ....................................................................................................................................8
WARRANTY .................................................................................................................................... 9
GENERAL SAFETY STANDARDS....................................................................................................... 10
Warning ................................................................................................................................................... 10
Safety regulations.................................................................................................................................... 10
DESCRIPTION ................................................................................................................................ 11
TECHNICAL DATA .......................................................................................................................... 11
INTENDED USE .............................................................................................................................. 11
UNINTENDED USE ......................................................................................................................... 11
Residual Risks........................................................................................................................................... 11
Section 3 ..................................................................................................................................13
UNPACKINGINSTRUCTIONS ........................................................................................................... 14
HANDLING .................................................................................................................................... 14
Locations.................................................................................................................................................. 14
Handling procedure................................................................................................................................. 14
POSITIONING, CONNECTION and DISCONNECTION ........................................................................ 14
Preliminary checks................................................................................................................................... 14
Preparation for use.................................................................................................................................. 15
USE............................................................................................................................................... 16
Issues ....................................................................................................................................................... 16
Procedures for use................................................................................................................................... 16
Production of 1.5/5 liters of colloidal silver………………...………..…………………………………………………………….17
Post-production recommendations and information………..……………..…………………………………………………18
Figures…………………..………………………………………………………………………………………………………………..………….19
Section 4 ..................................................................................................................................20
MAINTENANCE ............................................................................................................................. 21
Safety....................................................................................................................................................... 21
Periodic Maintenance.............................................................................................................................. 22
Extraordinary maintenance..................................................................................................................... 22
Fuse Replacement ………..…...………..……………………………………………………………………………………………… 22
DECOMMISSIONING...................................................................................................................... 22
Product deactivation.............................................................................................................................. 22
DISPOSAL................................................................................................................................................. 23

Manual – Silveraqua SV1 model
Page/3
Section 1
Declaration of conformity
Manufacturer's data
Authorized service
Presentation of this Manual
Attached documents

Manual – Silveraqua SV1 model
Page/4
DECLARATION OF CONFORMITY
The colloidal silver generator described in this documentation is accompanied by a declaration of conformity, drawn
up in compliance with the legislation in force in Europe.
NOTE
BEFORE USING THE PRODUCT IN ANY FORM, CHECK THE PRESENCE OF THE
DECLARATION OF CONFORMITY.
NOTE
IF THE PRODUCT IS TRANSFERRED TO A THIRD PARTY, ALL DOCUMENTATION MUST BE
DELIVERED ALONG WITH IT.
MANUFACTURER'S DATA
Company name
DLGSHOP di Del Grosso Stefano
Corporate headquarters
Via Chiantigiana, 36 - 52025 Montevarchi (AR) Italy
VAT No.
01733730517
Phone
[phone]
Fax
[phone]
E-mail
[email protected]
Website
www.silveraqua.it
AUTHORIZED SERVICE
Authorized service on the product is carried out directly by DLGSHOP or by a qualified technician appointed
by it.

Manual – Silveraqua SV1 model
Page/5
PRESENTATION OF THIS MANUAL
NOTE
UPON RECEIPT OF THE PRODUCT, BEFORE PERFORMING ANY OPERATION, READ THIS MANUAL
CAREFULLY
This manual contains instructions for positioning, connecting, operating and maintaining the colloidal silver
generator Silveraqua SV1 (hereinafter referred to as the SV1). The manual consists of several sections, each of
which covers a series of topics, subdivided into chapters and paragraphs.
The Index lists all topics covered in the manual. The numbering of the pages is progressive and each page contains the
page number. This manual is intended for the operator in charge of positioning, connecting, using and maintaining
the colloidal silver generator and refers to its technical life after its manufacturing and sale.
In the event that it is subsequently sold to third parties for any reason (sale, loan for use, or any other reason), the
colloidal silver generator must be delivered complete with all its documentation.
Before starting any operation, it is necessary to read the entire manual and then read in detail
the topic related to the operations to be carried out.
This manual contains proprietary and confidential information and may not be provided even in part to third parties
for any use or in any form without the prior written consent of DLGSHOP.
DLGSHOP states that the information contained in this manual is consistent with the technical and safety
specifications of the colloidal silver generator to which the manual refers.
A certified copy of this manual is stored in the technical file of the colloidal silver generator held at DLGSHOP.
DLGSHOP does not recognize any documentation not produced, issued or distributed by its offices or by its authorized
representatives.
This manual, like the entire technical file, will be stored by the manufacturer for the period required by law.
During this period, a copy of the documentation accompanying the product may be requested at the time of sale.
The entire technical file remains available for this period only to the supervisory authorities, which may request a
copy.
After this period, it will be the obligation and care of the party that manages the product to ensure that both the
product and the documentation comply with the laws in force at the time of inspection.

Manual – Silveraqua SV1 model
Page/6
Conventions
In order to obtain a more immediate understanding of the topics, the manual adopted the graphical and typographical
symbols and conventions described below.
Graphical Warning Conventions
NOTE
THE NOTES CONTAIN IMPORTANT INFORMATION, HIGHLIGHTED OUTSIDE THE TEXT TO WHICH
THEY REFER
WARNING!
WARNINGS INDICATE THOSE PROCEDURES WHOSE FULL OR PARTIAL NON-FULFILLMENT MAY
CAUSE DAMAGES TO THE PRODUCT OR ITS COMPONENTS AND MAY EXPOSE A USER TO
HAZARDS.
HAZARD
HAZARDS INDICATE THOSE PROCEDURES WHOSE FULL OR PARTIAL NON-FULFILLMENT MAY
CAUSE DAMAGES OR INJURIES TO THE HEALTH OF THE USER OR OTHER PEOPLE IN THE
VICINITY. SERIOUS DAMAGES TO THE PRODUCT.
Pictograms
The following pictograms can be found on the colloidal silver generator:
Hazards
Risk of electrocution
Area under voltage

Manual – Silveraqua SV1 model
Page/7
WARNING!
Pictograms that perform a safety role must not be removed, covered or damaged.
ATTACHED DOCUMENTATION
The documentation attached to the generator in addition to this manual is:
Adapter Manual
Adapter certificate of conformity downloadable from:
http://www.meanwell.com/webapp/product/search.aspx?prod=GS25E or you may request it from
[email protected]t
Declaration of conformity for the Sv1 generator downloadable from www.silveraqua.it .it under the
entry " “IL GENERATORE SILVERAQUA”(SILVERAQUA GENERATOR), or you may request it from
[email protected]t
NOTE
BEFORE USING THE PRODUCT, CHECK THE PRESENCE OF ALL ATTACHED DOCUMENTS.
NOTE
IF THE PRODUCT IS TRANSFERRED TO A THIRD PARTY, ALL DOCUMENTATION MUST BE
DELIVERED ALONG WITH IT.

Manual – Silveraqua SV1 model
Page/8
Section 2
Warranty
General safety requirements
Description and technical data
Intended and unintended use
Residual Risks

Manual – Silveraqua SV1 model
Page/9
WARRANTY
The warranty conditions, fully listed in the purchase agreement, only apply if the colloidal silver generator is used for
the intended use.
With the exception of ordinary and extraordinary maintenance interventions described in the
MAINTENANCE section and carried out in accordance with the indicated procedures, any repair or change
made to the product by the user or by unauthorized companies will void the warranty.
The warranty will not cover damages caused by inexperience or negligence in the use of the product, or by poor or
omitted maintenance.
Products sold by us are covered by warranty under the following conditions:
1
The warranty is valid for a period of twelve (12) or twenty-four (24) months depending on the type of buyer (legal person or natural person).
2
The manufacturer undertakes to replace, at its discretion, the malfunctioning parts or defective manufacturing parts, only after a careful
inspection and confirmation of faulty workmanship.

3
The buyer will bear the transportation and/or shipping costs in case of incorrect use of the warranty terms.

4
During the warranty period, replaced parts become the property of the manufacturer.

5
This warranty is only available to the original purchaser that complied with the standard maintenance instructions contained in the manual.
Our liability on the warranty expires when: the original owner transfers ownership of the product, or changes are made to the product.
6
The warranty does not cover damages caused by excessive stress, such as the use of the product after an identified malfunction, the use of
unsuitable operating methods or failure to comply with the operating and maintenance instructions.
7
The manufacturer shall not be liable for any difficulty that may arise in the resale or use abroad due to the provisions in force in the country
where the product was sold.

8
The defective product must be delivered or shipped to the manufacturer for repair or replacement; otherwise the replaced part will be
charged to the purchaser.

Attention: If it is necessary to make a claim under the warranty, please provide the following information:
1
Type
2
Date of purchase (submission of purchase document)
3
Detailed description of the issue
NOTE
FAILURE TO COMPLY WITH THE METHODS OF INTERVENTION AND USE OF THE PRODUCT
DESCRIBED IN THIS DOCUMENTATION WILL VOID THE WARRANTY.

Manual – Silveraqua SV1 model
Page/10
GENERAL SAFETY STANDARDS
Warning
If any part of the documentation is even just partially incomplete or illegible, contact DLGSHOP before carrying out
any further operation with the colloidal silver generator.
This chapter describes the general safety instructions to be complied with during any operation performed with the
product. The intervention procedures, described in the following chapters, must be carried out in compliance with the
implementation procedures and the general safety standards specified in this chapter.
The safety standards and the positioning, connection, use and maintenance procedures specified in this document
are complementary to the general safety standards on work safety that must be complied with.
Different countries may have different safety regulations. Therefore, it is specified that in all cases where the
documentation regulations happen to be in conflict or reductive compared to the regulations of the country in which
the colloidal silver generator is used, the regulations of the country will prevail over those of the documentation.
NOTE
THE MANUFACTURER CANNOT BE HELD LIABLE IN ANY CASE FOR ACCIDENTS OR DAMAGES
CAUSED BY THE UNINTENDED USE OF THE PRODUCT, AS WELL AS BY THE NON-COMPLIANCE
EVEN IF ARTIAL, WITH THE SAFETY REGULATIONS AND INTERVENTION PROCEDURES DESCRIBED
IN THE DOCUMENTATION.
The non-compliance with the regulations for use and the intervention, connection, use and maintenance of the
colloidal silver generator contained in the manual will also void the warranty,
Safety regulations
When using the colloidal silver generator, incorrect operating situations may occur which are not described in the
documentation. These abnormal situations can sometimes be caused by environmental factors or by accidental
failures not foreseeable by the manufacturer. If a problem occurs during the use of the product, contact the
manufacturer.
The manual must be kept by the personnel in charge of the management, maintenance and use of the
colloidal silver generator. In the event of deterioration or loss, the client may request a certified copy from the
manufacturer. We suggest to keep a backup copy in a place where it cannot be damaged or lost.
WARNING!
SINCE IT WOULD BE IMPOSSIBLE TO DESCRIBE ALL THE OPERATIONS THAT MUST NOT
OR CANNOT BE PERFORMED, PLEASE CONSIDER THAT ALL THE OPERATIONS (OTHER
THAN STANDARD INTENDED USE) THAT ARE NOT EXPLICITLY DESCRIBED IN THE
MANUAL PROVIDED WITH THE PRODUCT, MUST BE CONSIDERED AS NOT TO BE
PERFORMED.

Manual – Silveraqua SV1 model
Page/11
DESCRIPTION
The product described in the documentation is an electrolytic generator for the production of colloidal silver.
TECHNICAL DATA
Electrical power supply
Transformer 100-240V A.C.
frequency 50/60 Hz.
Output 48 V D.C.
Power: 25W
Transformer dimensions: L 54 mm x W 72 mm x H 79 mm
Transformer weight: about 186 gr
Generator dimensions: L 200 mm x W 150 mm x H 89 mm
Generator weight: about 500 gr
Glass slow blow fuse: 125 MA 250 VAC 5x20 mm
Power on with 0/1 positions
START/STOP control on the keyboard
INTENDED USE
The device must be used exclusively as a generator for the production of colloidal silver.
The silver generator is not a medical device, only colloidal silver can have this intended use.
UNINTENDED USE
No use other than the one described in the "DESCRIPTION" is intended use.
It is also absolutely forbidden to:
•use the product with incorrect electrical power supply.
•use the product for applications other than those intended.
•make changes to the product.
The reuse of any unit, after decommissioning the product, releases the manufacturer from any responsibility arising
from the use of the unit.
NOTE
THE MANUFACTURER CANNOT BE HELD LIABLE IN ANY WAY FOR ACCIDENTS OR DAMAGES
DUE TO UNINTENDED USE OF THE PRODUCT. ANY UNINTENDED USE OF THE PRODUCT WILL
VOID THE WARRANTY
Residual Risks
During the design stage, DLGSHOP carried out an in-depth risk analysis on the colloidal silver generator under review.
This analysis pointed out risks that are unavoidable by their nature. Therefore, these risks were examined individually
and instructions on how to avoid them were highlighted in this manual. Therefore, it is important that any
operator or user before positioning, connecting, using and maintaining the colloidal silver generator reads
this manual in advance.

Manual – Silveraqua SV1 model
Page/12
NOTE
THE MANUFACTURER CANNOT BE HELD LIABLE IN ANY WAY FOR ACCIDENTS OR DAMAGES
DUE TO UNINTENDED USE OF THE PRODUCT AS A RESULT OF NEGLIGENCE BY A USER.
In particular:
It is strictly forbidden to make any changes to the product. Any damage to persons, animals or property
resulting from the use of the colloidal silver generator, improperly modified by an unauthorized
operator, releases the manufacturer from any liability.
Carefully store this manual in a safe place as it is necessary for a correct and safe use of the product.
Periodically check the status of the label installed on the product and replace it if it is damaged. (if necessary,
contact the authorized service center)
If the external structure of the colloidal silver generator should have edges or sharp edges as a result of an
accidental impact, such as to make it hazardous, it is necessary to contact the authorized service center and
follow their instructions.
Important:
-Do not wet the electrical connections with water or other liquids.
-The maintenance described in the manual must be carried out.
-Maintenance must be carried out according to the instructions specified in the manual.
OPERATIONS INVOLVING RISKS FOR THE OPERATOR AND THE USER:
During commissioning, comply with the general accident prevention regulations.
In particular:
-If working on electrical parts, make sure that they are not under voltage.
Since the design stage, solutions were adopted to make the use of the product safe in all stages of use: transportation,
adjustment, operation and maintenance. Despite this, not all risks for users and the environment could be removed,
both for technological reasons (device reliability) and management reasons (excessive difficulties in removing them),
consequently the existing residual risks are reported herein, e.g.: electrocution, etc..

Manual – Silveraqua SV1 model
Page/13
Section 3
Unpacking Instructions
Handling
Positioning, Connection and Disconnection
Use
Figures

Manual – Silveraqua SV1 model
Page/14
UNPACKING INSTRUCTIONS
The colloidal silver generator is supplied in a cardboard box.
Inside the box you will find:
The Silveraqua SV1 generator
Two bars of 999.0% pure silver (about 50 mm wide, about 177 mm high and about 0.6 mm thick)
A magnetic stirrer
One transformer
HANDLING
Locations
It is recommended to take in consideration a few aspects before handling and using the colloidal silver
generator. In particular, a number of conditions need to be checked:
•The position must be chosen in such a way that it cannot be affected by jets of steam, water or other liquids.
•The colloidal silver generator must be used away from liquid, solid, gaseous or powdery substances, which
are flammable in contact with hot parts.
•It must be placed in ventilated rooms.
•The storage room temperature of the colloidal silver generator must be between 10°C and +40°C.
•The storage room temperature of the colloidal silver generator must be between 17°C and +30°C.
•Humidity conditions must be between 45% and 85%.
The colloidal silver generator can be used only indoors, respecting the above conditions.
Do not place the colloidal silver generator near: televisions, monitors, computers, mobile phones, magnetic
tapes/disks, medical equipment/prostheses, etc.
Pacemaker wearers may not use this equipment without medical authorization.
Do not place the switched-on colloidal silver generator in contact with other objects, as this may melt, burn and
damage them.
Handling procedure
Due to its size and weight, the product can be moved manually without any difficulty.
POSITIONING, CONNECTION and DISCONNECTION
Preliminary checks
The electrical system to which the colloidal silver generator will be connected must be in compliance with the
regulations in force and equipped with grounding system and an automatic circuit breaker.
All products are tested and tuned by the manufacturer before shipment and delivery to the client.
The product is designed, manufactured and tested to meet all specific regulations (see declaration of conformity), if
properly connected.
If the connection, use and/or maintenance of the colloidal silver generator are not properly carried out, faults and
safety issues may occur during operation. Improper connection and maintenance will void the warranty.

Manual – Silveraqua SV1 model
Page/15
WARNING!
THE PRODUCT MAY ONLY BE OPERATED AFTER IT IS PROPERLY POSITIONED AND CONNECTED.
Before positioning, connecting and operating the colloidal silver generator, completely remove any protection against
dust, moisture and any packaging material.
Check for damages
Make sure that the various parts of the colloidal silver generator are not physically damaged due to
impacts, tears or abrasions.
Make sure in particular that:
•there are no scratches or dents, which are an indication of impacts during transport;
•Make sure that no water, humidity or condensation entered during transport. If necessary, wait about 30
minutes before performing any further operation.
The lighting system (natural and/or artificial) of the area where the device will be positioned and used shall ensure the
following minimum values of illumination: 200 lux.
Damage Reporting Procedure
If damage is found, stop the procedure in progress and report the nature of the damage to the customer service of the
manufacturer.
Preparation for use
NOTE
THE MANUFACTURER CANNOT BE HELD LIABLE IN ANY CASE FOR ACCIDENTS OR DAMAGES
DUE TO THE USE OF THE PRODUCT CONNECTED TO AN ELECTRICAL POWER SUPPLY NOT IN
COMPLIANCE WITH THE LEGISLATION IN FORCE
1. Insert the magnetic stirrer by fitting it in the special shaft placed under the SV1, in the center between the
black clamps (FIGURE 1 on page 18
IMPORTANT NOTE: when the stirrer is inserted, there must be 1 or 2 mm of space between the box and the
stirrer, allowing the shaft to freely rotate (FIGURE 1A on page 18 Do not bend the stirrer when it is
inserted in the shaft as this may cause irreparable damage to the motor.
2. Unscrew the black clamps under the body of the SV1, position the two silver bars and tighten the nuts by
hand.
IMPORTANT NOTE: assemble the bars so that the distance between them is about 50 mm (FIGURE 2 on page
18).
3. Find a plastic/glass container with an opening between 110 mm and 160 mm and a minimum
height of 190 mm and a maximum height of 230 mm (the containers are available in our shop
www.silveraqua.it ).

Manual – Silveraqua SV1 model
Page/16
4. Fill up the container with water (Attention: the water used must be distilled water. It is possible to use
lab analysis water or water for pharmaceutical use as long as its value is equal or lower than 1 PPM) so
that the bars are dipped into the water for a minimum of 140 mm and a maximum of 155 mm.
(FIGURE 3 on page 19)
5. Important Note: Do not dip the SV1 into the water as it will be damaged.
Do not dip into the water the clamps that tighten the bars, since they are conductors and would prevent the
generation of colloidal silver.
6. Insert the power supply plug into the generator socket located on the back. (FIGURE 4 on page 18)
7. Plug the power supply into an electrical outlet that matches the electrical technical specifications of the
power supply. (PAGE 11 “TECHNICAL DATA”)
USE
Issues
In case of any unforeseen and hazardous abnormal conditions while using the colloidal silver generator, it is
recommended to follow this procedure:
•Disconnect the SV1 from the electrical power supply to which it is connected.
•Disconnect it from the electrical power sup by pulling out the plug from the electrical outlet.
•Immediately contact the manufacturer
In case of unexpected electromagnetic abnormal conditions after having powered or turned on the colloidal silver
generator, such as for example the impossibility of communicating through the telephone or smartphone, it is
recommended to follow this procedure:
•Disconnect it from the electrical power sup by pulling out the plug from the electrical outlet.
•Immediately contact technical support.
Procedures for use
WARNING!
When using the colloidal silver generator, it is necessary to wear the following personal protective equipment (PPE):
- Clothing:
it must comply with the basic safety requirements in force. Wear clothing with long sleeves.
- Gloves:
When working with parts that can reach high temperatures and parts under voltage, it is necessary to use EC
marked gloves to be protected against all the risks just listed.
- Goggles:
to protect the eyes of an operator against projected material.

Manual – Silveraqua SV1 model
Page/17
1Close the generator circuit breaker placing its handle on the 1 position; the light on the display will turn on
and the message "COLLOIDAL SILVER SV1 GENERATOR" will appear.
2Press S3 to set the speed of the stirrer; (_____% for 1.5 liters containers and _____% for 5 liters containers)
to increase the speed press P1, to decrease the speed press F2.
3Press S4 until "COLLOIDAL SILVER SV1 GENERATOR" appears.
4Press and hold START until you hear a loud audible signal, and the stirrer starts to run.
At this time, if the bars are dipped into the water as mentioned above, the display must show a voltage ranging from
36 to 38 volts and a current ranging from of 0.1 to 2.0 mA. These values are important because they indicate that the
water is double-distilled.
If these data were different, it would mean that the water is not suitable for producing colloidal silver with the SV1.
(use lab analysis water or water for pharmaceutical use as long as its value is equal or lower than 1 PPM)
From this moment on, if you followed the aforementioned procedure, the generator will start producing colloidal
silver. During production the SV1 will automatically adjust the "Voltage" and "Current".
Once the production is completed, press Stop, place the handle of the circuit breaker, located on the back (FIGURE 4
on page 18), on the 0 position, then disconnect the generator from the power supply by pulling out the plug from the
electrical outlet.
Remove the silver bars by unscrewing the black clamps located under the generator.
Pull out the stirrer following in reverse order the procedure used to insert it, do not bend the stirrer during this
operation since the motor shaft would be irreparably damaged.
Production of 1.5 liters of colloidal silver
To obtain 12/16 PPM it will take from 2 to 3 hours, with minimum water temperature 18°C (production time will vary
based on the water temperature)
As soon as the display shows "Current" reaches 7MA, it will be necessary to check the silver particles produced using a
PPM meter (“PPM” parts per million).
For a correct measurement of the PPM, we recommend the Hanna PWT (Pure Water Tester) model HI98308 to be
purchased along with the da buffer calibration HI7033.
IMPORTANT: Every time that the SV1 is removed from the water, measure the PPM, place the switch located on the
back (FIG. 4 page 19) from 1 to 0, disconnect it from the socket by unplugging it from the wall, and clean the silver
bars with absorbent paper since sediments that remained attached could end up in the water.
IMPORTANT: do not produce colloidal silver above 35 ppm because the silver particles stick together, the production
process must be completed without being interrupted (except for measurement).
Production of 5 liters of colloidal silver
To obtain 12/16 PPM it will take from 5 to 9 hours, with minimum water temperature 18°C (production time will vary
based on the water temperature) while it will take approximately 2 or 3 hours more to produce 20 PPM.
As soon as the display shows "Current" reaches 7MA, it will be necessary to check the silver particles produced using a
PPM meter (“PPM” parts per million).

Manual – Silveraqua SV1 model
Page/18
For a correct measurement of the PPM, we recommend the Hanna PWT (Pure Water Tester) model HI98308 to be
purchased along with the da buffer calibration HI7033.
IMPORTANT: Every time that the SV1 is removed from the water, measure the PPM, place the switch located on the
back (FIG. 4 page 19) from 1 to 0, disconnect it from the socket by unplugging it from the wall, and clean the silver
bars with absorbent paper since sediments that remained attached could end up in the water.
IMPORTANT: do not produce colloidal silver above 35 ppm because the silver particles stick together, the production
process must be completed without being interrupted (except for measurement).
Recommendations after production.
After the production, we recommend leaving the colloidal silver resting for at least 24/48 hours, (after said period, it is
possible that a few particles end up at the bottom of the container) then transfer the colloidal silver in glass bottles
discarding the particles deposited on the bottom of the container.
It is recommended to store the finished product in dark-glass containers, in a dark place away from heat sources and
electro-magnetic fields.
Information
After a few days, the PPM will stabilize, and they will be reduced by a few units.
It was noted that colloidal silver production exceeding 15/20 PPM are more sensitive to light; therefore, they may
have an amber color.
The magnetic stirrer provided, since it is white, after use may change color (see periodic maintenance instructions on
page 22)
Figures

Manual – Silveraqua SV1 model
Page/19

Manual – Silveraqua SV1 model
Page/20
Section 4
Maintenance
Decommissioning
Disposal