SilverCloud GL10 User manual

Instructiuni de utilizare si instalare
Stalp de gradina cu LED SilverCloud GL10
Cititi cu atentie acest manual si pastrati-l pentru consultare ulterioara.
Instalarea trebuie facuta doar de electricieni calificati care sunt informati cu standardele si normele de utilizare si instalare.
4. Conectati firele conform diagramei alaturate.
5. Fixati cu suruburi baza lampii in diblurile din beton.
Instructiuni de instalare:
NOTE:
ŸInainte de instalarea lampii LED, intrerupeti alimentarea la curent.
ŸNu priviti direct in lampa cand aceasta este aprinsa, intrucat lumina intensa poate cauza
afectiuni grave ochilor. 2
ŸCablu de alimentare recomandat: 3 x 1.0mm
ŸAsigurati-va ca ati conectat impamantarea
ŸNu folositi lampa fara geamul de protectie a LED-urilor
1. Faceti in sol o gaura de 250 x 250 x 150 mm. Scoateti prin aceasta gaura cablurile de
alimentare, astfel incat sa aiba o lungime utila de cel putin 300 mm.
2. Dupa ce ati cimentuit gaura facuta anterior, bagati in ciment suruburile si diblurile necesare
fixarii bazei lampii. Umpleti gaura cu ciment pana la nivelul solului. Asigurati-va ca suruburile
sunt suficient de lungi si corect amplasate astfel incat sa se potriveasca perfect in gaurile de pe
baza lampii. Lasati cimentul sa se intareasca inainte de fixarea lampii.
3. Scoateti cablurile din cutia de conexiuni a lampii, aflata sub baza acesteia.
Alimentare
220V
Consum
5W/200mA
Durata de viata
pana la 30000 ore
Eficienta energetica
85%
Tip LED
Ø5 LED
Numar LED-uri
2 x 12
Temperatura de culoare
6000K
Intensitate luminoasa
168 lm
Clasa de protectie
IP44
Umiditate de depozitare
<85%RH
Temperatura de depozitare
-45℃~+85℃
Temperatura de lucru
-45℃-+85℃
Material
Otel inoxidabil
Dimensiuni
Corp iluminat: 488 x 75 x 75 mm
Baza montaj: ø112 mm
2.
4. 4.
5.

User manual and installation instructions for
Stainless Steel Outdoor Lighting SilverCloud GL10
Please read these instructions carefully prior to installation and retain them for future reference. Installation must be performed by
qualified electricians who are informed about the standards and technical requirements of the appliance and its proper installation.
4. Connect the wire to the terminal block according
to the adiacent diagram.
5. Fix the lamp base with the screws by screw nuts.
Installation:
NOTES:
ŸBefore installation or maintenance, the electricity supply must be interrupted
ŸPlease do not look directly into the light when it is switched on
2
ŸPlease use 3 x 1.0mm wires
ŸBe sure to connect ground wire
ŸDo not use the LED lamp without protective glass
1. Dig a hole of 250 x 250 x 150 mm in the ground. Let the supply wires come out and above the
ground (at least 300 mm length)
2. Pour a small quantity of cement into the hole, then fix the screws into the cement. Adjust the
position of the screws, then continue to pour cement into the hole upto the surface of the ground.
Check the height of the screws and see whether they are suitable for fixing the LED lamp.
3. Open the connection box.
2.
4.
5.
Power supply
220V
Power consumption
5W/200mA
Life span
up to 30000 hours
Power supply efficiency
85%
LED
Ø5 LED chip
LED number
2 x 12
Color temperature
6000K
Luminous flux
168 lm
Waterproof
IP44
Storage humidity
RH<85%
Storage temperature
-45℃~+85℃
Working temperature
-45℃~+85℃
Material
Stainless steel
Dimensions
Body: 488 x 75 x 75 mm
Connections box: ø112 mm
4.