Silvercrest SEM 1100 A2 User manual

IAN 75769 IAN 75769
KOMPERNASS GMBH
Burgstraße 21
D-44867 Bochum
www.kompernass.com
Last Information Update · Tietojen tila · Informationsstatus
Tilstand af information · Stand der Informationen:
04/2012 · Ident.-No.: SEM1100A2032012-1
ESPRESSO MACHINE SEM 1100 A2
ESPRESSO MACHINE
Operating instructions
ESPRESSOMASKINE
Betjeningsvejledning
ESPRESSOMASKIN
Bruksanvisning
ESPRESSOKEITIN
Käyttöohje
GB/ IE Operating instructions Page 1
FI Käyttöohje Sivu 21
SE Bruksanvisning Sidan 39
DK Betjeningsvejledning Side 57
DE/ AT/ CH Bedienungsanleitung Seite 75
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of
the device.
Käännä ennen lukemista kuvallinen sivu esiin ja tutustu seuraavaksi laitteen kaikkiin toimintoihin.
Vik ut bildsidan och ha den till hands när du läser igenom anvisningarna och gör dig bekant med
apparatens/maskinens funktioner.
Før du læser, vend siden med billeder frem og bliv bekendt med alle apparatets funktioner.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.
ESPRESSOMASCHINE
Bedienungsanleitung
CV_75769_SEM1100A2_FI_SE_DK.indd 1-3 26.04.12 08:55

A
B
8
7
6
5
4
3
2
1
i
r
z
u
t
e w q 0
9
CV_75769_SEM1100A2_FI_SE_DK.indd 4-6 26.04.12 08:55

1
SEM 1100 A2
GB
IE
Index
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Limited liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Intended use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Items supplied / Transport inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Disposal of the packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Operating componentse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Filling the water tank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Heating-up after a long standing time /on the first use . . . . . . . . . . . . . . . . . . . . . . . 8
Heating up before every use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Preparing Espresso. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Preparing Cappuccino . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Tips for the milk froth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Generating hot water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Cleaning the milk frother . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Cleaning the hot water shower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Cleaning accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Cleaning the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Descaling the appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Disposal of the appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Warranty and Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Importer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
IB_75769_SEM1100A2_FI_SE_DK.indb Abs2:1 30.04.12 13:58

2SEM 1100 A2
GB
IE
Introduction
Congratulations on the purchase of your new appliance.
You have clearly decided in favour of a quality product. These operating instruc-
tions are a part of this product. They contain important information in regard to
safety, use and disposal. Before using the product, familiarise yourself with all of
these operating and safety instructions. Use the product only as described and
only for the specified areas of application. In addition, pass these documents on,
together with the product, to any future owner.
Copyright
This documentation is copyright protected.
All rights, including those of photographic reproduction, duplication and distribution
by means of particular methods (for example data processing, data carriers and
data networks), wholly or partially, as well as substantive and technical changes,
are reserved.
Limited liability
All technical information, data and information for installation and operation con-
tained in these operating instructions corresponds to the latest available at the
time of printing and, to the best of our knowledge, take into account our previous
experience and know-how.
No claims can be derived from the details, illustrations and descriptions in these
instructions.
The manufacturer assumes no responsibility for damage caused by failure to ob-
serve these instructions, improper use, inappropriate repairs, making unauthorized
modifications or for using unapproved replacement parts.
Warnings
In the extant operation instructions the following warnings are used:
WARNING
A warning of this risk level signifies a potentially dangerous
situation.
If the risk situation is not avoided it can lead to injuries.
► The directives in this warning are there to avoid personal injuries.
IB_75769_SEM1100A2_FI_SE_DK.indb Abs2:2 30.04.12 13:58

3
SEM 1100 A2
GB
IE
IMPORTANT
A warning of this risk level signifies potentially property
damage.
If the situation is not avoided it can lead to property damage.
► The directives in this warning are there to avoid property damage.
NOTICE
► A notice signifying additional information that assists in the operation of this
appliance.
Intended use
This appliance serves exclusively for the preparation of espresso/cappuccino and
the heating of water. It is intended solely for use in domestic households. Do not
use it for commercial applications.
This appliance is not intended for any other use or for uses beyond those detailed
here.
WARNING
Risk from unintended use!
Risks can come from the appliance if it is used for unintended purposes and/
or other types of use.
► Use this appliance exclusively for its intended purposes.
► Observe the procedures described in these operating instructions.
Claims of any kind for damage resulting from unintended use will not be accepted.
The operator alone bears liability.
IB_75769_SEM1100A2_FI_SE_DK.indb Abs2:3 30.04.12 13:58

4SEM 1100 A2
GB
IE
Items supplied / Transport inspection
WARNING
Risk of suffocation!
► Packaging material should not be used as a play thing.
There is a risk of suffocation!
The appliance is delivered with the following components as standard:
▯ Espresso Machine
▯ Sieve carrier
▯ large espresso sieve
▯ small espresso sieve
▯ Measuring spoon with compactor
▯ Operating Instructions
NOTICE
► Check the contents to make sure everything is available and there are no
signs of visible damage.
► If the contents are not complete, or are damaged due to defective packaging
or transportation, contact the service hotline.
Disposal of the packaging
The packaging protects the appliance from transport damage. The packaging
materials are selected from the point of view of their environmental friendliness
and disposal technology and are therefore recyclable.
The recirculation of packaging into the material circuit saves on raw material and
reduces generated waste. Dispose of packaging material that is no longer needed
according to the regionally established regulations.
NOTICE
► If possible preserve the appliance's original packaging during the warranty
period so that in the case of a warranty claim you can package the appli-
ance properly for return.
IB_75769_SEM1100A2_FI_SE_DK.indb Abs2:4 30.04.12 13:58

5
SEM 1100 A2
GB
IE
Safety instructions
For safe handling of the appliance observe the following safety information:
WARNING - RISK OF INJURY!
■ Before use check the appliance for visible external damage. Do not put into
operation an appliance that is damaged or has been dropped.
■ This appliance is not intended for use by individuals (including children) with
restricted physical, physiological or intellectual abilities or deficiences in ex-
perience and/or knowledge unless they are supervised by a person responsible
for their safety or receive from this person instruction in how the appliance is
to be used.
■ Children should be supervised to ensure that they do not play with the appli-
ance.
■ Repairs should only be carried out by authorized specialist companies or
by the Customer Service Department. Incorrect repairs can result in significant
risks for the user. In addition warranty claims become void.
■ NEVER submerse the appliance in water or other liquids. Risk of electric shock!
■ Never touch the appliance with wet or moist hands.
■ To avoid risks, arrange for defective plugs and/or cables to be replaced at
once by qualified technicians or our Customer Service Department.
■ Risk of Burns! During use, some parts become very hot!
■ Hot vapour plumes are formed when the product is in use. Take care to ensure
that you do not scald yourself! Keep a safe distance away from the steam.
■ Connect the appliance only to correctly installed and earthed mains power
sockets.
ATTENTION - PROPERTY DAMAGE
■ Defective components may only be replaced with original replacement parts.
Compliance with the safety requirements can only be assured by using original
replacement parts.
■ Protect the appliance from moisture and liquid penetration.
■ Protect the appliance against shock, moisture, dust, chemicals, extremes of
temperature and from being too close to sources of heat (ovens, radiators).
■ NEVER submerse the appliance in water or other liquids.
IB_75769_SEM1100A2_FI_SE_DK.indb Abs2:5 30.04.12 13:58

6SEM 1100 A2
GB
IE
■ Always pull the plug from the mains power socket; never pull on the cable.
■ Never leave the appliance unsupervised whilst in use.
■ Do not use an external timing switch or a separate remote control system to
operate the appliance.
■ Do not operate the appliance in rooms where the temperatures are below
or around 0° C. Should the water in the pipes or the water tank freeze, the
appliance could be damaged.
■ Never operate the appliance outdoors. This appliance is intended only for
indoor use.
NOTICE
► A repair to the appliance during the warranty period may only be carried
out by a cutomer service department authorized by the manufacturer
otherwise no additional warranty claims can be considered for subsequent
damages.
Operating componentse
1Water tank
2Steam regulation knob
3On/Off switch
4Green heating-up control lamp
5Rotary switch
6Compactor
7Recess for the red float
8Drip grill
9Measuring spoon with compactor
0small espresso sieve
qlarge espresso sieve
wSieve carrier
eSieve blocker
rDrip tray
tHot water shower
zMilk foamer
uGrip
iRed heating-up control lamp
IB_75769_SEM1100A2_FI_SE_DK.indb Abs2:6 30.04.12 13:58

7
SEM 1100 A2
GB
IE
Technical data
Voltage 220 - 240 V ∼ / 50 Hz
Nominal performance 1100 W
Pump pressure approx. 1.5 MPa (15 bar)
Water tank (Max) 1.5 Litres
Energy consumption in standby
mode until automatic switch-off approx. 31.3 Wh
Energy consumption in off-mode 0 Wh
Commissioning
1) Clean the sieve holder w, the measuring spoon 9, the espresso sieve 0 q,
the drip grill 8and the water tank 1as described in the chapter “Cleaning
and Care”.
2) Place the appliance on a level and heat-resistant surface. Ensure that a mains
power socket is in the vicinity.
3) Insert the drip grill 8so that the red float can protrude through the recess 7
in the drip grill 8.
4) Insert the plug into a mains power socket.
5) Proceed as follows before the first use, so as to clean the internal pipelines:
6) Allow sufficient water for about 5 cups of coffee to flow through the appli-
ance. Refer to the chapter “Operation”.
7) Let steam generate for about 30 seconds. Refer to the chapter “Operation”.
NOTICE
► On the first use it may be that the pump is already audibly working, noises
occur, but still no water is coming out of the appliance. In this case, turn
the steam control switch 2in the direction “+” so that air can escape from
the pipelines of the appliance (the function rotary switch 5stands at the
position “ “). After approx. 20 seconds the air will have escaped, the
noises disappear and water flows from the appliance.
IB_75769_SEM1100A2_FI_SE_DK.indb Abs2:7 30.04.12 13:58

8SEM 1100 A2
GB
IE
Operation
Filling the water tank
NOTICE
► Use only fresh drinking water for making espresso/cappuccino.
1) Pull the water tank 1upward and out, open the lid and fill it with water:
Fill it with water to at least the Min. marking.
Never fill it with more water than up to the Max marking.
2) Push the water tank 1back into the appliance so that it slides into the appli-
ance on the rails and sits firmly.
■ You can also fill the water tank 1without having to remove it from the appli-
ance. Simply open the water tank lid and fill it with water from a bottle etc.
Ensure that no water runs beside the water tank 1.
Heating-up after a long standing time/on the first use
If you have not used it for some time, preheat the appliance as follows:
1) Fill the water tank 1with water.
2) Place either the large qor the small espresso sieve 0in the sieve carrier w.
3) Insert the sieve carrier winto the appliance by placing it at the marking
“INSERT” and then turning it anticlockwise to the marking “LOCK”.
4) Place a cup under the sieve carrier w.
5) Close the steam regulation knob 2(turn it as far as it will go in the direction
“ - “).
6) Switch the appliance on with the on/off switch 3.
7) The red heating-up control lamp iglows.
8) Turn the rotary switch 5to the position “ ”. The pump begins to pump water
into the appliance. As soon as water flows from the sieve carrier opening, turn
the rotary switch 5back to the position “ ”.
9) As soon as the green heating-up control lamp 4glows, turn the rotary switch
5to the position “ ”. Allow the water to flow for about 1 minute. It may be
that you need to empty the cup in between. For this, briefly stop the process.
10) After approx. 1 minute turn the rotary switch back to the position “ ”.
11) Wait until the green heating-up control lamp 4glows again. The warming-up
is concluded. You can now prepare espresso.
IB_75769_SEM1100A2_FI_SE_DK.indb Abs2:8 30.04.12 13:58

9
SEM 1100 A2
GB
IE
Heating up before every use
Before you can prepare an espresso or cappuccino, the appliance must be heated up.
1) Switch the appliance on with the on/off switch 3. The rotary switch 5is at
the position “ “.
2) The red heating-up control lamp iglows.
3) Wait until the green heating-up control lamp 4glows.
You can now make an espresso / cappuccino.
Preparing Espresso
NOTICE
► If, before starting to make the espresso, you have taken hot steam from the
machine, we recommend you draw a little hot water before commencing
with the espresso preparation. If you do not, it may be that the coffee tastes
burnt. Hold an empty cup under the milk frother z. Turn the steam control
knob 2in the direction “+“. Turn the function rotary knob 5to the posi-
tion “ “ so that hot water flows out of the nozzle. Wait a few seconds
before turning the function rotary knob 5back to to the position “ “.
Then turn the steam control knob 2back to closed (in the direction “-“).
NOTICE
► Always ensure that the espresso sieve 0 q is clean and free of coffee
powder residues.
1) When the appliance is heated-up:
To prepare an espresso, place the small espresso sieve 0in the sieve carrier
w. To prepare two espressos, place the large espresso sieve q in the sieve
carrier w.
2) Fill the small espresso sieve 0to the max marking with espresso powder.
This equates to approx. 7g of powder or a levelled measuring spoon 9.
or...
Fill the large espresso sieve qto the max marking with espresso powder.
This equates to about 7g + 7g of powder or two levelled measuring spoons
9.
3) Compress the espresso powder using the tamper on the appliance 6. Then,
if necessary, fill it with more espresso powder, until the espresso sieb 0 q is
full up to the Max marking. Tamp the coffee powder down once again.
IB_75769_SEM1100A2_FI_SE_DK.indb Abs2:9 30.04.12 13:58

10 SEM 1100 A2
GB
IE
NOTICE
► Compaction of the coffee powder is an essential process for the prepara-
tion of an espresso. If the espresso powder is compacted very strongly, the
espresso runs through more slowly and there is more crema. If the espresso
powder is not so strongly compacted, the espresso runs through more
quickly and it creates very little crema.
4) Insert the sieve carrier winto the appliance by placing it at the marking
“INSERT” and then turning it anticlockwise to the marking “LOCK”.
5) Place one (or two) cup(s) under the sieve carrier openings. We recommend
that you rinse the cups out with hot water beforehand, so that the espresso
does not cool so quickly.
6) As soon as the green heating-up control lamp 4glows, you can turn the
rotary switch 5to the position “ ”. The espresso flows into the cup(s).
WARNING
Never remove the sieve carrier wduring the espresso output!
The resulting spray of hot espresso would lead to injury!!
► Always ensure that the rotary switch 5stands at “ “ before you remo-
ve the sieve carrier w.
NOTICE
► This appliance is fitted with a pre-brew function. This means that the hot
water, before it is pressed through the espresso powder, stands for a short
time in the filter holder. This refines the aroma of the espresso.
7) When the cup(s) are filled to the desired quantity (about 20 ml), turn the
rotary switch 5back to the position “ ”.
You can now drink the espresso.
8) Switch the appliance off with the on/off switch 3.
NOTICE
► After 3 minutes the appliance will switch itself off automatically.
9) After every use remove the espresso powder from the espresso sieve 0 q.
Remove the sieve holder wfrom the appliance. Flip the sieve blocker e
upwards so that the espresso sieve 0 q cannot fall out of the sieve holder
w. Now empty the espresso sieve 0 q. Always dispose of the espresso
powder or espresso pads in an environmentally friendly manner, for example,
with the organic waste.
IB_75769_SEM1100A2_FI_SE_DK.indb Abs2:10 30.04.12 13:58

11
SEM 1100 A2
GB
IE
NOTICE
► Absolutely clean the hot water shower tafter every use. Refer to the
chapter "Cleaning and Care".
NOTICE
► Regularly empty the drip tray r, at the latest when the red float in the
recess 7of the drip grill 8is visible.
NOTICE
► You can also use espresso pads for the preparation of espresso. Use only
espresso pads that correspond to the ESE standard. The ESE standard is
a system accepted by the leading manufacturers of espresso pads, which
makes possible the simple and clean preparation of espresso.
Preparing Cappuccino
WARNING
Be careful when working with steam for the milk foam production!
The hot steam or hot splashes can lead to injuries!
► Always operate the steam regulation knob 2slowly.
1) Fill a container for frothing (preferably made of stainless steel) to third with
cold milk.
2) Ensure that the steam regulation knob 2is closed (turn it as far as it will go
in the direction “-”).
3) Push the milk foamer zout to the side. Thereby, take hold of it only by the
grip u.
4) Turn the rotary switch 5to the position “ ”. Wait until the green heating-up
control lamp 4glows.
5) Hold an empty container under the milk frother z. Slowly turn the steam con-
trol knob 2in the direction “+”. Condensed water/spray comes from the noz-
zle. Thus, the nozzle and the water circulation inside the appliance is cleaned.
IB_75769_SEM1100A2_FI_SE_DK.indb Abs2:11 30.04.12 13:58

12 SEM 1100 A2
GB
IE
6) When only steam comes out of the nozzle, turn the steam control knob 2in
the direction “-” until no more steam comes out of the nozzle. Pour the water
in the container away.
7) Now hold the frothing container in your hand, so as to feel the milk tempera-
ture, and guide the nozzle of the milk frother zlightly into the milk. Thereby,
hold the frothing container at a slight angle.
8) Slowly turn the steam control knob 2in the direction “+”.
9) Rotate the container for frothing in a circular motion and hold the tip of the
nozzle just below the surface of the milk: deep enough so that the milk does
not spray in all directions and high enough so that a thick foam is produced.
Done properly, a deep buzzing sound is audible.
10) As the milk froth rises place the nozzle deeper in the milk, to froth up the next
“layer” and to avoid a burnt taste in the foam.
11) Finally, insert the nozzle completely and close the steam control knob 2
a little, so that the milk is heated. Hold the frothing container at a slight angle,
so that the milk gently spins around while it is being stirred with the nozzle.
12) When the milk foam has the desired consistency and temperature, switch the
steam control knob 2off (up to the stop in the “-” direction).
13) First then remove the nozzle from the milk.
14) Turn the rotary switch 5to the position “ ”.
NOTICE
► For the preparation of cappuccino always use bigger cups than for espresso,
because foamed milk will be added.
15) For the preparation of a cappuccino, proceed exactly as you would for an
espresso (see chapter “Preparing espresso“/ the heating up is no longer nec-
essary). Allow the water to pass through only for about twice as long as an
espresso (about 40 ml).
16) Switch the appliance off with the on/off switch 3.
NOTICE
► After 3 minutes the appliance will switch itself off automatically.
17) Now add the frothed milk into the previously prepared espresso. The cappuc-
cino is now ready. According to taste, you can add sugar or sprinkle it with
cocoa powder.
IB_75769_SEM1100A2_FI_SE_DK.indb Abs2:12 30.04.12 13:58

13
SEM 1100 A2
GB
IE
NOTICE
► You can also use the milk frother zto heat up other liquids, such as cocoa
or tea.
NOTICE
► Absolutely clean the milk frother zafter every use. Refer to the chapter
"Cleaning and Care".
Tips for the milk froth
■ In principle, any type of milk can be frothed, including soy and rice milk.
However, some types of milk can only be frothed with limitations.
■ Skimmed or low-fat milk does not burn as easily as whole milk, but with a too
low fat content there is a risk that the milk froth will not be good. Therefore, if
possible use a milk with 3.5% or 1.5% fat content.
■ Well chilled milk can be frothed better than less cold.
■ Do not froth milk up a second time, otherwise it could burn on.
■ Allow frothed milk to stand for about 30 seconds before you pour it onto the
espresso. Thus, larger bubbles burst and still fluid milk falls to the bottom. You
can then pour the fine froth onto the espresso.
Generating hot water
1) When the appliance is heated-up:
2) Place a cup under the milk frother z.
3) When the green heating-up control lamp 4glows, turn the steam control
knob 2to the position “+”.
4) Turn the rotary switch 5to the position “ ”. Hot water flows from the nozzle.
5) If you wish to interrupt the hot water supply, turn the steam control knob 2
off (as far as it will go in the direction “-”) and place the rotary switch 5at
the position “ ”.
6) Switch the appliance off with the on/off switch 3.
NOTICE
► After 3 minutes the appliance will switch itself off automatically.
IB_75769_SEM1100A2_FI_SE_DK.indb Abs2:13 30.04.12 13:58

14 SEM 1100 A2
GB
IE
Cleaning and Care
WARNING - RISK OF INJURY!
■ Always remove the plug from the mains power socket before you clean the
appliance. Risk of electric shock!
■ Always allow the appliance to cool down before you start to clean it. Risk of
Burns!
■ NEVER submerse the appliance in water or other liquids. Risk of electric shock!
Cleaning the milk frother
ATTENTION - PROPERTY DAMAGE
■ NEVER use abrasive, corrosive or chemical agents to clean the appliance.
These could damage the upper surfaces of the appliance.
1) Place an empty container under the milk frother z.
2) Immediately after use turn the steam control knob 2to the position “+ “ and,
for a few seconds, allow the steam to escape.
3) Turn the steam control knob 2off (as far as it will go in the direction “-”),
switch the appliance off and remove the plug from the mains power socket.
4) Allow the nozzle to cool down.
5) Remove the nozzle and clean it thoroughly in warm water.
6) Check to see if the small hole in the nozzle is clogged and, if so, clear it with
a needle.
7) Clean the steam delivery tube of the milk frother zwith a damp cloth.
8) Replace the nozzle back onto the steam supply pipe.
IB_75769_SEM1100A2_FI_SE_DK.indb Abs2:14 30.04.12 13:58

15
SEM 1100 A2
GB
IE
Cleaning the hot water shower
Clean the hot water shower tafter each use:
1) After you have prepared the espresso/cappuccino and removed the sieve
holder w, wipe the entire surface of the hot water shower twith a moist
cloth so that all powder residues are removed.
2) Insert the filter holder wback in without the espresso filters 0q.
3) Then place an empty cup under the hot water spray tand turn the rotary
function switch 5to the position “ “. Water flows from the hot water spray
tand rinses the last of the powder residue out.
4) After about 20 seconds place the rotary function switch 5back to the positi-
on “ “ and then switch the appliance off with the On/Off switch 3.
5) Take the filter holder wback off.
Cleaning accessories
1) Clean the filter holder w, the two coffee filters 0q, the water tank 1, the
measuring scoop 9and the drip tray 8in warm water.
NOTICE
► If you put detergent into the water, it may have a negative effect on the taste
of the espresso. If the stains can only be removed with detergent, always
rinse the items afterwards with lots of clean water.
2) Dry all parts well.
3) The drip tray ris suitable for cleaning in the dishwasher.
Cleaning the appliance
Clean the housing with a moist cloth. If necessary, use a little detergent on the
cloth.
Descaling the appliance
Regularly descale the appliance. The appliance should be descaled after about
200 espresso preparations. Depending on the hardness of the water in your area,
this figure may differ.
For descaling, use commercial available descaler for espresso machines. Proceed
as described in the instructions for usage of the descaler.
If you do not have a descaler, you can proceed as follows:
1) Fill the water tank 1to the marking MAX.
IB_75769_SEM1100A2_FI_SE_DK.indb Abs2:15 30.04.12 13:58

16 SEM 1100 A2
GB
IE
2) Dissolve 2 tablespoons (about 30 grams) of citric acid (available in drug-
stores or chemists) into the water.
3) Replace the water tank 1into the appliance.
4) Switch the appliance on with the on/off switch 3. The rotary switch 5must
be in the position “ ”. The steam control knob 2is closed.
5) Insert the sieve carrier w, WITHOUT espresso powder, into the appliance
and place a cup under the sieve carrier w. As soon as the green heating-up
control lamp 4glows, turn the rotary switch 5to the position “ ”.
6) Let about 2 cups (coffee cups) of water pass through and then stop the process.
7) Hold a container under the milk frother z.
8) Place the rotary switch 5at the position “ ” and wait until the green heat-
ing-up control lamp 4glows. Slowly turn the steam control knob 2to the
position “+ “. Allow the appliance to create steam for about 2 minutes.
9) After 2 minutes close the steam control knob 2, set the rotary switch 5to the
position “ ” and switch the appliance off.
10) Let the scaling agent take effect for about 15 minutes.
11) Repeat the steps 4 - 10 three times.
12) Then place the rotary switch 5at the position “ ” and let the solution flow
through until the water tank 1is empty.
13) Rinse the water tank 1with clean water and then fill it with clean water up
to the Max marking.
14) Turn the rotary switch 5to the position “ ” as soon as the green heating-
up control lamp 4glows.
15) Allow the water to run through.
16) Repeat the steps 13 - 15 three times.
17) Fill the water tank 1with water once again.
18) Turn the rotary switch 5to the position “ ”.
19) Hold a container under the milk frother zand slowly rotate the steam control
knob 2to the position “+” as soon as the green heating-up control lamp 4
glows.
20) After about 1 minute close the steam control knob 2, set the rotary switch 5
to the position “ ” and switch the appliance off.
NOTICE
► After 3 minutes the appliance will switch itself off automatically.
IB_75769_SEM1100A2_FI_SE_DK.indb Abs2:16 30.04.12 13:58

17
SEM 1100 A2
GB
IE
Troubleshooting
Problem Cause Remedy
The espresso no
longer flows out.
• The espresso powder is too
moist and/or compressed
too tight.
• Reprepare the espresso,
however, this time do not
compress it so tightly, or
exchange it completely.
• No water in the water tank 1.• Fill the water tank 1
with water.
• The holes in the sieve carrier
openings are blocked. • Clean the sieve carrier w.
the espresso drips over
the edges of the sieve
carrier winstead of
from the openings.
• The sieve carrier wis not
correctly inserted.
• Correctly insert the sieve
carrier w.
• The sieve carrier openings
are blocked. • Clean the sieve carrier w.
• There are espresso powder
residues on the edges of the
sieve carrier w.
• Clean the espresso
powder residues from
the edges of the sieve
carrier w.
The espresso is cold.
• The appliance was not
preheated. • Preheat the appliance.
• The green heating-up control
lamp 4has not yet glowed.
• Wait until the green
heating-up control lamp
4glows.
• The cups were not prewarmed. • Prewarm the cups.
Noisy operation
of the pump.
• The water tank 1is empty. • Fill the water tank 1
with water.
• The water tank 1is not properly
inserted, meaning that water
cannot enter into the appliance.
• Correctly insert the water
tank 1.
IB_75769_SEM1100A2_FI_SE_DK.indb Abs2:17 30.04.12 13:58

18 SEM 1100 A2
GB
IE The crema is too light
(the espresso runs
quickly out of the
sieve carrier w).
• too little espresso powder. • Use more espresso
powder.
• The espresso powder is too
coarsely ground.
• Use only the espresso
powder specially manu-
factured for espresso.
The crema is too dark
(the espresso runs
slowly out of the
sieve carrier w).
• too much espresso powder. • Use less espresso
powder.
• The powder is too finely ground
or moist.
• Use only the espresso
powder specially manu-
factured for espresso.
• The sieve is blocked. • Clean the sieve.
The milk does not foam.
• The milk is not cold enough. • Use milk from the
refrigerator.
• The milk foamer zis dirty. • Clean the milk foamer z.
Disposal
Disposal of the appliance
Do not dispose of this appliance in your normal domestic waste.
This product is subject to the provisions of the European Directive
2002/96/EC-WEEE (Waste Electrical and Electronic Equipment).
Dispose of this appliance through an approved waste disposal centre or at your
community waste facility. Observe the currently applicable regulations. In case of
doubt, please contact your waste disposal centre.
IB_75769_SEM1100A2_FI_SE_DK.indb Abs2:18 30.04.12 13:58