Sime Superior Ci Installation instructions

Supplied By www.heating spares.co Tel. [phone]
Superior Ci
User Instructions
GB
PLEASE LEAVE THIS INSTRUCTION
WITH THE USER

Supplied By www.heating spares.co Tel. [phone]
USER INSTRUCTIONS
VERY IMPORTANT!
PLEASE MAKE SURE YOUR LOG BOOK ENCLOSED IS ILLED IN CORRECTLY.
ALL CORGI REGISTERED INSTALLERS CARRY A CORGI ID CARD.
BOTH SHOULD BE RECORDED IN YOUR CENTRAL HEATING LOG BOOK.
YOU CAN CHECK YOUR INSTALLER IS CORGI REGISTERED
BY CALLING ON 01256 372300
GAS SAFETY [INSTALLATION AND USE] REGULATIONS [as
amended]. It is the law that a registered erson, in accor-
dance with the above regulations, installs all gas a liances.
Failure to install a liances correctly could lead to rosecu-
tion. It is in your own interest, and that of safety, to ensure
that the law is com lied with.
It is essential that the appliance be correctly earthed.
An electricity supply of 230 V~ 50 Hz fused at 3 A is
required.
Read these instructions carefully before attem ting to o er-
ate the a liance.
1.1 INTRODUCTION
The Sime “Superior Ci” are a range of wall mounted cast iron
boilers. They utilise a fully automatic ignition system together
with electronic tem erature control. The combustion system
is fan assisted and uses a concentric flue and air duct that
can exit the boiler to either side or to the rear, ending in a
small balanced flue terminal on the outside wall.
The a liance is suitable for use with natural gas.
1.2 APPLIANCE OPERATION
The installation engineer will have set the range rated a li-
ance to the correct heating requirement for the ro erty.
There should be no need to adjust the boiler control once it
has been set unless the tem erature set oint needs to be
increased or decreased. The thermostat knob will adjust the
set oint tem erature of the electronic controls in the a li-
ance. Turning clockwise increases the set oint.
A demand for heat from the external controls will:
– check the air ressure switch,
– start the fan,
– confirm correct air flow through the a liance,
– start the s ark generator,
– o en the gas valve,
– ignite and rove the flame,
– monitor the a liance flow tem erature, switching the
a liance on and off as necessary.
– should the a liance fail to light, the lockout button will illu-
minate.
1.3 OPERATING INSTRUCTIONS
1.3.1 To light the appliance
– Turn on the electrical su ly and set all external controls
to on.
– Turn the boiler control to maximum and check the um is
o erating correctly and water is circulating.
– After a short eriod the ignition lockout indicator will be illu-
minated, after a 10 second wait de ress the lockout button
to reset the ignition sequence. Turn off the boiler control.
OPERATING INSTRUCTIONS OR THE USER
IGNITION AND
TEMPERATURE CONTROL
LOCK-OUT BUTTON
OVERHEAT WARNING LAMP
APPLIANCE CONTROLS

Supplied By www.heating spares.co Tel. [phone]
– Turn on the gas su ly.
– Turn the boiler control on, and to maximum. Check the
boiler lights.
– Set the boiler control to the required tem erature for the
maximum boiler flow. Turning clockwise increases the set
oint tem erature.
– Make sure the external controls are fully o erational and
the com lete system is controlled correctly.
1.3.2 To turn the appliance off
The a liance may need to be switched off for short eriods.
If required the boiler control may be rotated to the ‘OFF’ osi-
tion (com letely anti clock wise) which will revent the a li-
ance from o erating in the event of a demand from any exter-
nal controls.
If the a liance is to be switched off for long eriods the boil-
er control should be rotated to ‘OFF’ and the electrical su ly
to the com lete system should be isolated.
If the a liance is to be switched off for a rolonged length of
time during severe cold conditions then it is recommended
that the com lete heating system and a liance is drained to
revent freezing. A service engineer would normally be
required for this.
If a frost thermostat is fitted to the heating system, no draining
of the system is required, leave the a liance switched on and the
tem erature control at its minimum setting and turn any external
timer controls off. This will allow the a liance to o erate via the
frost thermostat and revent the system from freezing.
1.4 MINIMUM CLEARANCES
The following MINIMUM CLEARANCES must be available for
servicing the a liance:
1.5 ROUTINE SERVICING
To ensure continued efficient o eration of the a liance, it is
recommended that it is checked and serviced as necessary
at regular intervals.
The frequency of servicing will de end u on the articular
installation conditions and usage but in general once a year
should be adequate. It is the law that any service work must
be carried out by a registerd erson (C.O.R.G.I.).
1.6 GENERAL IN ORMATION
1.6.1 Appliance overheat thermostat
The a liance is fitted with a safety cutout thermostat. In the
event of the a liance overheating this will revent the a li-
ance from functioning.
If this occurs, both the overheat warning lam and the ignition
lock out indicator will illuminate. Allow the a liance to cool,
de ress the ignition-reset button and turn the rotary control
to ‘OFF’. Switch the electricity su ly to the a liance off, this
will reset the overheat warning lam . Switch the electricity
su ly to the a liance on and reset the rotary control to its
original osition. If the external controls are calling for heat,
the a liance will erform an ignition sequence and the burn-
er will light.
If the situation is re eated, turn off the electrical su ly and
consult your installer or a service engineer.
1.6.2 Electrical supply
An interru tion in the electrical su ly whilst the burner is
alight may cause the overheat thermostat to o erate. If this
ha ens and the electrical su ly is restored whilst in this
condition, the warning lam s may illuminate after an ignition
sequence (refer to section 1.6.1). However should the electri-
cal su ly be restored after the a liance has cooled, normal
o eration will be restored.
1.6.3 Cleaning
Use only a dam cloth and mild detergent to clean the a li-
ance outer casing. Do not use abrasive cleaners. It is recom-
mended to clean the outer case when the a liance is cold.
1.7 SA ETY
It is essential that the instructions in this book are strictly fol-
lowed for the safe and economical o eration of this a liance.
The a liance functions as a fan assisted balanced flue unit.
The flue terminal MUST NOT BE OBSTRUCTED under any cir-
cumstances. If damaged, turn off the a liance and consult
the installer, service engineer or gas su lier. If it is known or
sus ected that a fault exists on the a liance it MUST NOT be
used until a com etent erson has rectified the fault.
WARNING: I A GAS LEAK IS SUSPECTED OR EXISTS,
TURN O THE GAS SUPPLY TO THE APPLIANCE AT THE
GAS SERVICE COCK. DO NOT OPERATE ANY ELECTRICAL
SWITCHES. DO NOT OPERATE ANY ELECTRICAL APPLI-
ANCES. OPEN ALL WINDOWS AND DOORS. DO NOT
SMOKE. EXTINGUISH ALL NAKED LAMES. CONTACT THE
GAS SUPPLIER IMMEDIATELY.
ABOVE THE APPLIANCE CASING 200 mm 8 in
AT THE R.H.S. 15 m m 5/
8in
AT THE L.H.S. 15 m m 5/
8in
BELOW THE APPLIANCE CASING 200 mm 7 7/
8in
IN RONT O THE APPLIANCE 500 mm 19 3/
4in
All descri tions and illustrations rovided in this manual have been carefully re ared but we reserve the right to make changes
and im rovements in our roducts that may affect the accuracy of the information contained in this manual.

Supplied By www.heating spares.co Tel. [phone]
Cod. 6274224A - Documentation Dpt.
Sime Ltd
Unit D2 Enterprise Way, Bradford Road, Bradford, West Yorkshire, BD10 EW
Tel. [phone] - Fax [phone]
www.sime.ltd.uk - e-mail: enquir[email protected]