Simons Voss Technologies GatewayNode 2 User manual

GatewayNode 2
Manual
17.06.2021

Contents
1 General .......................................................................................................................................................... 3
2 General safety instructions.....................................................................................................................4
3 Product-specific safety instructions.................................................................................................... 7
4 Meaning of the text formatting .............................................................................................................8
5 Scope of delivery........................................................................................................................................9
5.1 Accessories .........................................................................................................................................................9
6 Connections............................................................................................................................................... 10
7 Installation ...................................................................................................................................................11
7.1 Antenna ...............................................................................................................................................................12
8 Initial operation..........................................................................................................................................15
8.1 IPsettings............................................................................................................................................................ 15
9 Maintenance.............................................................................................................................................. 16
10 Signalling .....................................................................................................................................................17
11 Fault rectification..................................................................................................................................... 18
11.1 Reset .................................................................................................................................................................... 18
12 Technical specifications ....................................................................................................................... 20
12.1 Optional external antenna ........................................................................................................................22
12.1.1 Electrical specifications ............................................................................................................ 22
12.1.2 Connection specifications........................................................................................................22
12.1.3 Mechanical specifications and dimensions ....................................................................23
13 EU/UK Declaration of conformity.......................................................................................................24
14 Help and other information ..................................................................................................................25
GatewayNode 2 (Manual) Contents
2 / 27

1 General
GatewayNode 2 (Manual) 1. General
3 / 27

2 General safety instructions
Signal word (ANSI
Z535.6) Possible immediate effects of non-compliance
DANGER Death or serious injury (likely)
WARNING Death or serious injury (possible, but unlikely)
CAUTION Minor injury
IMPORTANT Property damage or malfunction
NOTE Low or none
WARNING
Blocked access
Access through a door may stay blocked due to incorrectly fitted and/or in-
correctly programmed components. SimonsVoss Technologies GmbH is
not liable for the consequences of blocked access such as access to in-
jured or endangered persons, material damage or other damage!
Blocked access through manipulation of the product
If you change the product on your own, malfunctions can occur and access through a door can
be blocked.
Modify the product only when needed and only in the manner described in the
documentation.
IMPORTANT
Damage resulting from electrostatic discharge (ESD)
This product contains electronic components that may be damaged by electrostatic discharges.
1. Use ESD-compliant working materials (e.g. Grounding strap).
2. Ground yourself before carrying out any work that could bring you into contact with the
electronics. For this purpose, touch earthed metallic surfaces (e.g. door frames, water pipes
or heating valves).
Damage resulting from liquids
This product contains electronic components that may be damaged by liquids of any kind.
Keep liquids away from the electronics.
Damage resulting from aggressive cleaning agents
The surface of this product may be damaged as a result of the use of unsuitable cleaning agents.
Only use cleaning agents that are suitable for plastic or metal surfaces.
GatewayNode 2 (Manual) 2. General safety instructions
4 / 27

Damage as a result of mechanical impact
This product contains electronic components that may be damaged by mechanical impacts of
any kind.
1. Avoid touching the electronics.
2. Avoid other mechanical influences on the electronics.
Damage as a result of overcurrent or overvoltage
This product contains electronic components that may be damaged by excessive current or
voltage.
Do not exceed the maximum permissible voltages and/or currents.
Damage due to polarity reversal
This product contains electronic components that may be damaged by reverse polarity of the
power source.
Do not reverse the polarity of the voltage source (batteries or mains adapters).
Operational malfunction due to radio interference
This product may be affected by electromagnetic or magnetic interference.
Do not mount or place the product directly next to devices that could cause electromagnetic
or magnetic interference (switching power supplies!).
Communication interference due to metallic surfaces
This product communicates wirelessly. Metallic surfaces can greatly reduce the range of the
product.
Do not mount or place the product on or near metallic surfaces.
NOTE
Intended use
SmartIntego-products are designed exclusively for opening and closing
doors and similar objects.
Do not use SmartIntego products for any other purposes.
Qualifications required
The installation and commissioning requires specialized knowledge.
Only trained personnel may install and commission the product.
Incorrect installation
SimonsVoss Technologies GmbH accepts no liability for damage caused to doors or compon-
ents due to incorrect fitting or installation.
Modifications or further technical developments cannot be excluded and may be implemented
without notice.
GatewayNode 2 (Manual) 2. General safety instructions
5 / 27

The German language version is the original instruction manual. Other languages (drafting in the
contract language) are translations of the original instructions.
Read and follow all installation, installation, and commissioning instructions. Pass these instruc-
tions and any maintenance instructions to the user.
GatewayNode 2 (Manual) 2. General safety instructions
6 / 27

3 Product-specific safety instructions
CAUTION
Risk of burns due to hot circuit board
If you power the device with Power-over-Ethernet (PoE), the board can be-
come very hot.
Allow the unit to cool down before opening the housing.
Risk of electric shock from connected power supply
The device is supplied with power during operation. Opening the housing and touching live parts
may result in electric shock.
1. If the power supply is connected, do not open the housing.
2. Disconnect the power supply (or disconnect the network cable) before opening the housing.
NOTE
Unauthorised access with standard access data
The standard access data can be viewed freely. Unauthorised persons can-
not change the access authorisations, but they can change the network
configuration. You will then no longer be able to reach the device via the
network and will have to reset it.
Some browsers do not transmit spaces at the beginning of the password.
1. Change the default password.
2. Do not start or end the password with spaces.
Further documentation
You can find further documentation about SmartIntego products on the SmartIntego page
(www.smartintego.com).
GatewayNode 2 (Manual) 3. Product-specific safety instructions
7 / 27

4 Meaning of the text formatting
This documentation uses text formatting and design elements to facilitate
understanding. The table explains the meaning of possible text formatting:
Example button
Example
Example checkbox
Example Option
[Example] Tab
"Example" Name of a displayed window
|Example| Upper programme bar
Example Entry in the expanded upper pro-
gramme bar
Example Context menu entry
▼ Example Name of a drop-down menu
"Example" Selection option in a drop-down
menu
"Example" Area
Example Field
Example
Name of a (Windows) service
Example
Commands (e.g. Windows CMD
commands)
Example Database entry
[Example] MobileKey type selection
GatewayNode 2 (Manual) 4. Meaning of the text formatting
8 / 27

5 Scope of delivery
GatewayNode 2: Cover, base plate with circuit board and three pre-
assembled strain reliefs
Removable sticker with Chip-ID
Quick guide
5.1 Accessories
You can use optionally available accessories to adapt your device to
different applications.
Order code Name Purpose
ANTENNA.EXT.868 External antennas
You can connect the
external antenna to the
MCX connector of the
circuit board and im-
prove reception (see
Antenna [}12]
).
POWER.SUPPLY.2 Power supply (12 VDC,
500 mA)
You can use this power
supply unit to power
your device.
GatewayNode 2 (Manual) 5. Scope of delivery
9 / 27

6 Connections
DC In RJ45 ANT
IO
IO-Vout GND
+ 3.3 V
Analog Input
Unused
DI 3
DI 2
DI 1
O 3
O 2
O 1.NC
O 1.NO
O 1.COM
NOTE
IO connector only for RouterNode 2
You can only use the connectors of the IO connector at RouterNode 2.
Connection Meaning
DC In Pin connector Power supply with round
plug connector
IO-Vout
Terminal block: GND Auxiliary voltage output -
Earth connection
Terminal block: +3.3 V Auxiliary voltage output -
Positive pole
RJ45 Network connection
ANT
Connector for external an-
tenna (see
Antenna
[}12]
)
GatewayNode 2 (Manual) 6. Connections
10 / 27

7 Installation
The device can be mounted horizontally or vertically. You can carry out the
horizontal mounting easily and safely with the integrated mounting holes.
Observe the radiation pattern of the internal antenna (see
Antenna
[}12]
) and align the device appropriately.
IMPORTANT
Adverse effect on reception due to interferences
This device communicates wirelessly. Wireless communication can be affected or may fail due
to metal surfaces or interference.
1. Do not fit the device to metal surfaces.
2. Keep the device away from sources of electrical or magnetic interference.
Unauthorised access
If the electrical contacts in the device are short-circuited by unauthorised persons, undesired re-
actions may occur.
Mount the device in an environment that is protected from unauthorised access.
Malfunctions due to weather conditions
This device is not protected against splash water and other weather influences.
Mount the device in an environment that is protected from the weather.
Wiring to device
You can install the cables both on (surface-mounted) and under (flush-
mounted) plaster.
If you install the cables under the plaster, then use the opening
integrated in the base plate.
If you lay the cables on the plaster, then you must modify the housing.
üPower supply disconnected.
1. Push the ribbed area laterally inwards and remove the housing cover.
GatewayNode 2 (Manual) 7. Installation
11 / 27

2. Check the required width of the housing opening. The height of the
opening is approx. 7 mm. Each removed bar widens the opening by 4
mm.
3. Select a location where you want to remove the bars.
IMPORTANT
Insufficient fit due to removed clips
The housing cover is positioned and held by clips on the webs. If you saw
off or break off these clips, the housing cover will no longer be held at this
point.
1. Do not remove any bars that have a clip over them.
2. Do not damage clips during sawing.
4. Use a suitable saw to saw through the bars at both ends of the desired
opening to the base plate.
5. Bend the bars back and forth at the desired opening until the bars break.
9The housing is prepared for surface mounting.
7.1 Antenna
The internal antenna radiates as shown. The transmitting and receiving
power is therefore different depending on the direction and is possibly
influenced by the environment (sources of interference and/or metallic
surfaces).
GatewayNode 2 (Manual) 7. Installation
12 / 27

External antennas
Use the external antenna if any of the following problems occur.
Transmission and reception behaviour not stable
Range too short
Transmission and reception outdoors (LockNodes available outdoors)
The external antenna is suitable for outdoor use. This allows you to place
the device in the protected area while the antenna is outdoors.
The scope of delivery of the external antenna includes:
Integrated magnetic base
Wall mounting material
Dowels and screws
You do not need to change any settings after connecting the external
antenna. When the external antenna is connected, the device transmits via
the internal and external antennas (the internal antenna is not disabled by
connecting the external antenna).
üPower supply disconnected.
1. Open the housing.
GatewayNode 2 (Manual) 7. Installation
13 / 27

2. Locate the connector socket on the circuit board.
3. Connect the external antenna to the connector socket.
9The external antenna is connected.
4. Close the housing again.
9The device transmits via internal and external antenna.
GatewayNode 2 (Manual) 7. Installation
14 / 27

8 Initial operation
1. Mount the device (see
Installation [}11]
).
2. Supply the device with power.
3. Connect the device to your network.
4. Use the OAM-Tool to determine the IP address of your device in the
network (see OAM-Tool manual).
5. Connect the device to your system (see SmartIntego TechGuide).
9The device has been put into operation and is now flashing green slowly
(see
Signalling [}17]
).
8.1 IPsettings
Your device can be addressed via an IP address in the network. There are
two ways to integrate your device into the network:
Automatic assignment of an IP address by a DHCP server in the
network: Unless you make other settings, an IP address is automatically
assigned to your device by a DHCP server. You can change this IP
address manually later. If you do not know the IP address, you can
determine the IP address with the OAM tool.
Manual assignment of an IP address: Assign the IP address manually.
You can change the IP settings in the SmartIntego Manager.
If you reset the network settings in your device (see
Reset [}18]
), the
default IP address will only be restored if you assign it manually. However, if
the IP address was assigned by a DHCP server, the IP address will be
reassigned by the DHCP server directly following reset.
GatewayNode 2 (Manual) 8. Initial operation
15 / 27

9 Maintenance
The device itself is maintenance-free. However, the performance of radio
networks will always depend on environmental influences. These
influences can change and affect the performance of your radio network.
You should therefore check the network configuration and performance of
your radio network at regular intervals.
CAUTION
Network failure in critical situations
With the System 3060 and WaveNet you can implement emergency func-
tions such as amok protection. These emergency functions are critical.
1. Test locking systems in which critical emergency functions are
implemented at least once a month.
2. If necessary, also comply with other standards and regulations
according to which your system is operated.
GatewayNode 2 (Manual) 9. Maintenance
16 / 27

10 Signalling
Signal Meaning
Green flashing (~1.5 Hz) Configured and ready to use.
Green flashing (~0.3Hz) Not configured, but ready for opera-
tion
Red flashing (briefly) Restart
Green flickering Data transfer
GatewayNode 2 (Manual) 10. Signalling
17 / 27

11 Fault rectification
If problems occur during operation, you may be able to rectify them
yourself:
1. Check the power supply of the affected devices.
2. Check the network connection.
3. Check the authorisations assigned.
11.1 Reset
If problems should occur or you want to reset the device to its initial state,
you can reset the device with the reset button.
Make a distinction between them:
Reset SmartIntego configuration: Reset all SmartIntego settings.
Reset network configuration: Reset all network settings (IP address,
DHCP settings, host name).
NOTE
IP address recovery
If the IP address is assigned by a DHCP server (default setting), the DHCP
server assigns the IP address again directly after resetting (depending on
settings of the DHCP server).
Reset the SmartIntego configuration
1. Disconnect the power supply (round plug or network cable for PoE).
2. Wait 20 seconds.
3. Press and hold the reset button.
4. Reconnect the power supply (round plug or network cable for PoE).
5. Release the reset button after one second.
9Device flashes green again (see
Signalling [}17]
).
9SmartIntego configuration is reset.
GatewayNode 2 (Manual) 11. Fault rectification
18 / 27

Reset network configuration
1. Disconnect the power supply (round plug or network cable for PoE).
2. Wait 20 seconds.
3. Press and hold the reset button.
4. Reconnect the power supply (round plug or network cable for PoE).
5. Release the reset button after five seconds.
9Device flashes green again (see
Signalling [}17]
).
9Network configuration is reset.
NOTE
Unauthorised access with standard access data
The standard access data can be viewed freely. Unauthorised persons can-
not change the access authorisations, but they can change the network
configuration. You will then no longer be able to reach the device via the
network and will have to reset it.
Some browsers do not transmit spaces at the beginning of the password.
1. Change the default password.
2. Do not start or end the password with spaces.
You receive the device with the following factory configuration:
IPaddress 192,168,100,100
User name SimonsVoss
Password SimonsVoss
The IP address of your device on your network can be determined using the
free OAM tool (
https://www.simons-voss.com/de/downloads/software-
downloads.html
). Please refer to the manual for more information.
GatewayNode 2 (Manual) 11. Fault rectification
19 / 27

12 Technical specifications
General
Dimensions 172mm × 86mm × 33mm
Weight About 100g
Material ABS plastic, UV-stable
Colour White (like RAL 9016 "Traffic white")
Installation
horizontal
vertical
Wall mounting possible
Integrated strain relief (3x)
Connections
RJ45 (Network/PoE)
Round plug Ø 5.5 mm, Ø pin 2.0 mm
(power supply)
Screw terminal block 2-pole, wire
diameter 0.14 mm2 to 1.5 mm2 (power
supply for external applications)
MCX socket (optional external
antenna)
Power supply via PoE and round plug
possible simultaneously: round plug >
12VDC → Round plug used, round plug <
12VDC → PoE used
Environment
Temperature
Operational: -10°C to +55°C
Storage: -20°C to +60°C
Humidity Max. 90%, non-condensing
Standard protection rating IP20
Electric
Operating voltage
9 VDC to 32 VDC (reverse polarity protec-
ted) or PoE according to IEEE 802.3af
Power supply via PoE and round plug
possible simultaneously: round plug >
12VDC → Round plug used, round plug <
12VDC → PoE used
Output max. 3 W
GatewayNode 2 (Manual) 12. Technical specifications
20 / 27
Table of contents
Popular Gateway manuals by other brands

Motorola
Motorola SURFboard SVG7782 user guide

AudioCodes
AudioCodes Mediant 3000 user manual

Primus
Primus SmartRG 505 Quick install guide

Dell
Dell Edge 3000 Series Installation and operation manual

Innovaphone
Innovaphone IP6010 datasheet

ZyXEL Communications
ZyXEL Communications P-660HW-Tx v3 Series user guide