Simplicity 1000 DC User manual

DC Pumps
SIMPLICITYAQUATICS.COM
PROBLEM? PLEASE DO NOT RETURN THE
PRODUCT TO THE PLACE OF PURCHASE.
Please visit our website at www.simplicityaquatics.com/support
for additional information and videos. Need more help? Please
contact us directly at [e-mail] or
424-757-6150 and we’ll be happy to help you out.
QUICK START GUIDE
Parts List
Installation
SUBMERSIBLE USE ONLY
1. Plumb pump with barb fittings (included) or
threaded fittings (not included) and desired tubing.
Please use included O-rings with the barb fittings
to minimize leakage and only hand tighten the hose
bard retaining collar. Do NOT tighten with tools as
breakage may occur.
2. Attach intake screen to pump body.
3. Place pump in water being careful not to
submerge the connector on the end of the cord.
If the connector gets wet, it MUST be dried out
completely prior to use.
4. Connect pump electrical cable to controller. Please
make sure the connection is tight and firm, and
use the water resistant retaining collar to reduce
exposure to moisture.
5. Connect power supply to controller.
6. Mount the controller and the power supply in an
area free from heat, water and moisture, ideally in
an area with good airflow to allow the components
to remain cool.
8. Double-check all connections.
9. Connect power cord to power supply.
10. Plug power cord into grounded outlet.
A. [–] button decreases flow and reduces energy
consumption
B. [+] button increases flow and increases energy
consumption
C. FEED button stops the pump for 10 minutes for
feeding or maintenance. Pump will automatically
restart after 10 minutes or can be restarted
manually by pressing the feed button again.
D. FEED light illuminates when FEED mode is enabled.
E. 10 LED lights indicate the current flow settings.
Controller Operation
• Pump Body
• Controller
• Electronic Power Supply
• Grounded Power Cord
• Intake Screen
• Plumbing Part Kit
Max. Flow Rate Min. Flow Rate
1000 DC 1,000 gph 790 gph
1600 DC 1,600 gph 1,150 gph
2100 DC 2,100 gph 1,350 gph
3200 DC 3,200 gph 1,400 gph
A B C
DE
Lock / Unl oc k
• Lock: Press the [+] or [–] button for 3 to 4 seconds
until the controller LED lights flash twice.
• Unlock: Press the [+] or [–] button for 3 to 4 seconds
until the controller LED lights flash twice again.

DC Pumps
SIMPLICITYAQUATICS.COM
Safety Information
Please take great care when installing and using this pump. This is an electrical device and, as with any electrical
device used in or around an aquarium, caution needs to be exercised. Failure to do so may result in electrocution,
fire, serious bodily injury or even death. Please follow these safety requirements carefully, as failure to do so will
void the warranty and could cause serious safety hazards.
Ne ed m o re h el p? For more information on pump setup and operation please visit www.simplicityaquatics.com/support/
Troubleshooting & Maintenance
For troubleshooting, maintenance and other frequently
asked questions, please visit www.simplicityaquatics.com
Warranty
For warranty information, please visit
www.simplicityaquatics.com/support/warranty/
NEVER operate the pump if it has been damaged
or is malfunctioning.
NEVER operate the controller with wet hands or
if the controller is wet.
NEVER re-wire, re-configure or modify the pump
in any way.
NEVER use with generators.
NEVER grab the pump or controller by the
electrical cord as this may cause the wires to
become exposed.
NEVER use the pump in water above
95˚ Fahrenheit.
NEVER use the pump in anything but freshwater
or saltwater.
NEVER use the pump for a swimming pool or
other body of water intended for human use.
NEVER run the pump dry.
NEVER run the pump in water deeper than
54 inches.
NEVER install the controller outdoors or in a
wet environment.
NEVER subject the controller to direct heat,
such as sunlight or heat lamps.
ALWAYS unplug the pump from its power source
before doing any work on the pump or placing
hands in water.
ALWAYS leave a bit of slack in the electrical
cord to help absorb any pump vibrations.
ALWAYS use of a GFCI (Ground-fault
Circuit Interrupter).
ALWAYS keep away from children.
ALWAYS run the pump completely submerged
in water.
ALWAYS run the pump with a drip loop in the
power cord to prevent moisture from reaching
your power receptacle.
ALWAYS run the controller with adequate space
to allow cooling.
ALWAYS place the power supply in a cool,
dry location.