Simply45 S45-175 User manual

Best Practice
Termination Instructions
Congratulations on purchasing the Simply45® S45-1750P
ProSeries Pass Through Shielded External Ground RJ45 Modular
Plugs for Cat6 STP Cables PE Insulated.
Our ProSeries Pass Through RJ45 plugs include the
uniquely designed and patent pending Cap45™.
P/N:S45-1750P
Simply45® ProSeries Pass Through
Shielded RJ45 Modular Plugs
(patent pending)

STEP 1
Using the Simply45 Adjustable LAN Cable Stripper
(S45-S01BL/YL) or wire stripper on the Simply45
Heavy Duty RJ45 Crimp Tool (S45-C100/S45-C101),
score the cable jacket about 1.25” (3cm) from the
cable end Be sure not to cut too deep where the
wire conductors could be nicked. Remove the
stripped cable jacket.
STEP 3
Trim all cable shielding (AL foil, metal braid) back to the cable jacket. We recommend
using the Simply45 5” Angled Flush Cutter (S45-801). Do not cut o the drain wire.
Fold the drain wire straight back about 1inch (2.5cm) over the cable jacket.
If there is a center spline/pair separator cut it o as close to the jacket as possible
without nicking the wire conductors.
STEP 2
Slide the S45-1750P metal shell onto
the cable jacket with the front of the
shell facing the termination end. Slide it
back out of the way for the moment.

STEP 4
Untwist and straighten the wire conductors. We recommend using the Simply45
Adjustable LAN Cable Stripper (S45-S01BL/YL) that has a wire straightener comb on
the top. Next, align the wires in the correct alignment pattern (Type A or B).
The B pattern is the most used today.
STEP 5
Bar45™ - Following the pattern above, insert the top and bottom wires into the load
bar. Once inserted, make sure the wires follow the pattern correctly.
T568A
GR BL
T568B
WO WG
WBL
WBR
WG
TOP ROW
BOTTOM ROW
WO
WBL
WBR

STEP 6
Slide the Bar45 load bar as far back to the cable jacket as you can. Bar45 is designed
to slide back almost touching the cable jacket. [NOTE: This is important for reducing
the length of untwisted wire inside the RJ45 plug and improving termination
performance]. Next, using the S45-801 Flush Cutter, trim the wire ends straight
leaving about 0.75” (2.0cm) protruding past the front of the Bar45 load bar.
STEP 7
Insert the cable with the Bar45 into the plug allowing the wires to come out through the front of
the plug as shown above. The S45-1750P plug is designed to accommodate insertion of large
diameter cables up to 8.0mm (0.315”). Work the cable jacket into the plug until fully inserted.
Looking from underneath the plug, the cable jacket should meet or come close to the horizontal
line (see above). Make sure the drain wire remains straight down the cable jacket.

STEP 8
Insert the loaded plug into the Simply45
Heavy Duty RJ45 Crimp Tool (S45-C100/
S45-C101). Make sure to completely
insert the plug into the crimper socket.
STEP 9
Compress the crimper handles all the
way down with one swift and firm
motion until the handles release.
STEP 10
Verify that the wires are still correctly aligned to the pattern. Slide the S45-1750P
metal shell over the plug body as shown above. Press-In on the bottom of the plug as
you attach the shell. This will allow the plug to snap into the metal shell. The drain wire
should remain straight back against the cable jacket and come out of the back of the
metal shell and extend pass the external ground arm.

STEP 11
Push the external ground arm down over the
drain wire and against the cable jacket. The
drain wire should meet the rear end of the
external ground arm. Using your fingers or a
flat head screwdriver, loosely fold the external
ground arm wings around the cable jacket.
STEP 12
Using the external ground arm crimp feature on
the Simply45 Shielded External Ground Crimper
(S45-C101), crimp the external ground wings until
securely folded around the cable jacket. You can
also use pliers (S45-802) to accomplish this task.
STEP 13
Inspect the terminated plug to be sure wires have been properly trimmed. Then align the 2 posts on the Cap45
with the 2 holes on the front of the plug. Push the posts into the plug until the Cap45 is snug to the plug body.
Simply45®, Cap45™, and Bar45™ are trademarks of Simply45 LLC © All rights reserved.
by You can view these instructions online and learn
more Best Practices at www.simply45.com