Sit-Stand Yo-Yo Desk 90 User manual

Please read all instructions carefully before using this product. Retain this
manual for future reference. The specifications of this product may vary slightly
from the illustrations and are subject to change without notice.
CAUTION
TM
Assembly Manual
TM

TECHNICAL DATA
You will find the following items inside your package, please check them.
If there are any tools or components missing, please contact customer
services on [phone].
ASSEMBLY KIT
Page 2 / 8
950
≤
610
≤
150~500
890 590
790
560
A Minimum 3KG - Maximum 15KG
WEIGHT TOLERANCE LEVEL
B Maximum 2KG
A
B
The Desktop and Keyboard Tray have
a defined weight tolerance level. Do not
exceed the maximum bearing weight.
WARNING
x1 x1
x12 x4
x1
Screwdriver1 x Keyboard Tray Brackets (Left and Right)2 x
Keyboard Tray1 xDesktop & Frame1 x Screws12 x Yo-Yo Side Caps2 x Cable Ties4 x
A B C
x1
[phone]
[email protected] Delta 606, Swindon, Wiltshire SN5 7XF
TM
TM
x1
x2
TM

ASSEMBLY STEP 1
Please take the Yo-Yo Desk out of the packaging, and place it on your table/desk.
Please place the Yo-Yo Desk on a surface suitable to hold the entire base of the
Yo-Yo Desk otherwise you may cause damage when operating the Yo-Yo Desk.
CAUTION
+
Page 3 / 8
[phone]
[email protected] Delta 606, Swindon, Wiltshire SN5 7XF

ASSEMBLY STEP 2
AAttach the Yo-Yo Desk Side Cap to the connecting arm.
BUse the 8 screws provided to attach the Keyboard Tray Brackets
to the Keyboard Tray using a Philips Screwdriver.
C,D Hang the Keyboard Tray Brackets on the Rotating Bracket
Holders provided, and then tighten.
Page 4 / 8
[phone]
[email protected] Delta 606, Swindon, Wiltshire SN5 7XF
CAUTION
When attaching Brackets to Tray, avoid
excessive screwdriver force . Excessive
force may result in reduced screw grip &
make the Keyboard Tray defective.
Tighten
A
B
CD
Rotating Bracket Holders

ASSEMBLY STEP 3
Adjust the desk to your appropriate sitting/standing heights, by LIFTING BOTH
LEVERS (on right & left sides) SIMULTANEOUSLY.
Please don’t place your hands on the supporting bars, as they move during
adjustment, and may cause injury.
CAUTION
Page 5 / 8
[phone]
[email protected] Delta 606, Swindon, Wiltshire SN5 7XF
TM

ASSEMBLY STEP 4
Please make sure that all equipment is fully on top of the Yo-Yo Desk. It should
not hang over the edges, as this may result in a fall and cause harm/get
damaged.
Please put your equipment on top of the Yo-Yo Desk.
CAUTION
Page 6 / 8
[phone]
[email protected] Delta 606, Swindon, Wiltshire SN5 7XF

When using the adhesive Cable Ties, make sure that you leave enough length
in the cable to allow for the full range of height adjustment, otherwise your
equipment may get damaged.
ASSEMBLY STEP 5
The Cable Tie uses velcro adhesive, making
it easy for you to tidy your cables.
CAUTION
Page 7 / 8
Cable
Cable Ties
[phone]
[email protected] Delta 606, Swindon, Wiltshire SN5 7XF

Please don’t put your hands on the supporting
bars, as they move during adjustment and
may cause injury.
Please make sure that all equipment is fully on top
of theYo-Yo Desk, not hanging over the edges, as
it may fall and cause harm/get damaged.
When using the adhesive Cable Ties, make sure that
you leave enough length in the cable to allow for the
full range of height adjustment, otherwise your
equipment may get damaged.
When first using your desk, please carefully set it to
its maximum height, to check that you can raise the
desk without causing damage to your equipment
or yourself.
Please ask someone to assist you when lifting the
desk to prevent causing harm or injury.
CAUTION
CAUTION
CAUTION
CAUTION
CAUTION
W A R N I N G
!
Page 8 / 8
Do not place your hand near the strut. Strut's angle will
change during the desktop lifts and it may hurt you.
Hands Pinching
[phone]
[email protected] Delta 606, Swindon, Wiltshire SN5 7XF