Skyvue NXG-55 User manual

Portable Cart & Tilt Mount
Assembly Manual
NXG 55

3
Portable Cart ManualnXG 55 |
Table of Contents
PORTABLE CART INSTALLATION ...................................... 4
PARTS FOR POST ASSEMBLY ........................................ 4
TILT MOUNTS .................................................................. 5
BASE PLATE ASSEMBLY ................................................. 6
POST TO PLAY ASSEMBLY ............................................. 8
POST TILT MOUNT ASSEMBLY ....................................... 11
PARTS FOR POST TILT MOUNT .................................... 13
TILT MOUNTS ................................................................ 14
U-BOLTS AND MOUNTING PLATE ASSEMBLY............. 15

4All Rights Reserved. 2017 SkyVue®
Assembly Manual- Portable Cart
Parts for Post Assembly:
1. 1- Post
2. 1- Base Plate
3. 1 - Post Lock - Handle
4. 4 - Outriggers
front
back
this item is found in parts box
Gather the following:

5
Portable Cart ManualnXG 55 |
Tools Required for Post Assembly:
Tilt Mounts:
The tilt mount portion of a portable cart is provided in a separate box
labeled “PTM” and is size specic. See below for the appropriate sizes.
55” Class
Televisions
Ratchet
with 9/16” Socket Crescent Wrench
and
9/16”
9/16”

6All Rights Reserved. 2017 SkyVue®
Assembly Manual- Portable Cart
Gather the following:
Caster (Wheel) to Outrigger Assembly:
4 qty. - Outriggers
4 Casters - Each caster comes with 4 sets of bolts and nuts.
Remove each bolt, and nut from each caster and
place accordingly.
You will need all bolts and nuts supplied with each
caster to complite the assembly.
Next gather an one outrigger and place
the caster in line with the 4 hole plate
the outrigger.
The correct holes should be closest to the end
which is capped off.
Insert the 4 bolts supplied with the caster from
the bottom so that the bolt heads are on the same
side as the caster as show in the image.
Re apply the 4 nuts from the rst step onto the
bolts as seen in the image and tighten using prop-
er tooling to secure the caster to the outrigger.
Once this is done reapeat these instructions and
steps three more times for the remaining casters
and outriggers.
With all for outriggers assembled proceed to the
next stage of the assembly process.

7
Portable Cart ManualnXG 55 |
Gather the following:
Base Plate Assembly:
4 qty. - Outriggers
Base Plate
Remove the bolts, washers and nuts
from the four outriggers as shown.
Align the holes on outriggers with
the indicated holes on the base plate
as shown.

8All Rights Reserved. 2017 SkyVue®
Assembly Manual- Portable Cart
With the outriggers underneath the base plate, reinsert the same bolts
through the base plate, and into the outriggers. Place the at washers and
nylock nuts back onto the bolts and hand tighten.
With outriggers in place, tight-
en down all nuts by placing
the ratchet on the nut side
with the Allen wrench on the
other.
The base plate is complete when all four (4) outriggers are securely
attached and tightened.

9
Portable Cart ManualnXG 55 |
Post to Plate Assembly:
Set Screw
Preinstalled
Post Lock - Handle Hole
Located on side
Bottom of Post
Brass Fitting for
Friction Reduction
Lower Cable Exit Hole
Upper Cable Entry Hole

10 All Rights Reserved. 2017 SkyVue®
You have now completed the cart assembly portion of your
Portable Cart Mount.

11
Portable Cart ManualnXG 55 |

Post Tilt Mount
Assembly Manual
NXG 5550

13
Post titl Mount ManualnXG 55 |
Parts for Tilt Mount Assembly:
1. Previously assembled post:
Deck Post, In-ground Post, or
Portable Cart
2. 2- U-Bolts - (4) Flat Washers,
(4) Lock Washers,
(4) Powder Coated Nuts
3. 2- U-Bolt Saddles
4. 4 - Rubber Bolt Caps
5. Appropriately sized tilt mount
(Located in the box labeled “PTM”)
these items are found in parts box

14 All Rights Reserved. 2017 SkyVue®
Assembly Manual- Post Tilt Mount
Tools Required for PTM Assembly:
Tilt Mounts:
The tilt mount portion of a portable cart is provided in a separate box
labeled “PTM” and is size specic.
Ratchet
with 9/16” Socket Crescent Wrench
and
9/16”
PTM Boxes will contain the following items:
2- Mounting Arms
1- Mounting Plate
1- Locking Bar
9/16”

15
Post titl Mount ManualnXG 55 |
U-Bolts and
Mounting Plate Assembly:
U-Bolts should be hooked around the post and through the holes on the
U-Bolt Saddles. These should be positioned near the upper cable entry
hole.
With U-Bolts and saddles in place,
slide mounting plate over the U-bolt
ends.
U-Bolt
Post
Saddle
Top View

16 All Rights Reserved. 2017 SkyVue®
Assembly Manual- Post Tilt Mount
1. With U-bolts threaded through the mounting plates, place
stainless steel at washers over the bolt ends.
2. Place stainless steel lock washers over bolt ends.
3. Thread black powder coated nuts over bolt ends and hand tighten.
See figure 3a for suggested mounting plate placement.
4. Once positioned, level and tighten all U-bolt nuts on mounting
plate.
5. Place rubber bolt caps over exposed bolt ends
U-Bolts and
Mounting Plate Assembly Cont.:

17
Post titl Mount ManualnXG 55 |

18 All Rights Reserved. 2017 SkyVue®
Assembly Manual- Post Tilt Mount
Warning: Do not plug speaker bar into A/C outlet until connections to the tele-
vision have been plugged in. This will severely damage the speaker bar if not
followed completely.
Lay television down, viewing side down on blanket.
Lay blanket down on at
sturdy surface. Run hand
over surface to make sure
there are no sharp object
or protrusions, when the
television is laying down.

19
Post titl Mount ManualnXG 55 |
The following instructions apply to NXG 55” Television
1: Remove the hex head screws and
washers. Set the screws and washers in a
secure location.
2: Insert spring nuts as shown in
picture (2 per power strut). Spring should
be touching both sides of the power strut
as shown.
Gather the 4clamping nuts with springs. These will be in a separate
bag shipped with the User Manual Packet.
3: Align holes of the mounting arms
with the holes of the clamp nut springs.
The arms should be level with each
other. Insert the hex head screws and
washers from the rst step and secure
tightly as shown in the example to the
right and below.
Note:
KNobs should
beFaciNg sides oF
televisioN.

20 All Rights Reserved. 2017 SkyVue®
Assembly Manual- Post Tilt Mount
With the help from a friend, lift the television and attach the hooks on the
mounting arms to the plate on the tilt mount. Tighten knobs on arms once
the tilt is set correctly for the television.
Once the television is hung on the plate. Be sure to tighten the position set
screw on the bottom of the mounting arm to secure the television in place.
HOOK
SECURE BY
INSERTING
LOCKING BAR
SET & TIGHTEN
KNOBS
Congratulations you have successfully installed your post tilt mount. If you
have any questions feel free to contact our technical support team
[phone] option 2
Mounting Arm
Mount Plate
Locking Bar