Skywalker SWTCS15 Quick guide

USER MANUAL
Skywalker Holdings LLC
P.O. Box 574, Brigham City, UT 84302
ASSEMBLY, MAINTENANCE, &
MODEL #SWTCS15 / SWTCS015
WARNING
Read all precautions and instructions in
this manual before using this equipment.
Save this manual for future reference.
Maximum user weight 250 lbs.

2
IMPORTANT
Trampolines and enclosures are susceptible
to winds. Be sure to secure your trampoline
and enclosure. Wind damage is not covered
in the warranty of your trampoline.
WARNING
CHOKING HAZARD- Small
parts not for children
under 3 years.
WARNING
Adult assembly required.
STOP EVERYTHING YOU'RE DOING AND REGISTER YOUR TRAMPOLINE
Find our warranty registration online by typing in: www.skywalkertrampolines.com/registration/
You'll need to have the following information handy:
• Name • Email address
• Address • Trampoline model number
• Phone number • Trampoline serial number
• Date of purchase • Retailer the trampoline was purchased from
HEY WE'VE GOT SOMETHING REALLY IMPORTANT TO SAY
And that is... check us out online! We've got assembly videos (for those of you who prefer movies over books), FAQs
(so you know you're not the only one who messed up), fascinating blog posts (did you know jumping burns more
calories than running?), and most importantly... find us on social media! Because we want to be your friend. We'd love
to hear from you, friend.
Website: skywalkertrampolines.com
Facebook: facebook.com/skywalkertrampolines
YouTube: youtube.com/c/SkywalkerTrampolines
Pinterest: pinterest.com/swtrampolines
Twitter: twitter.com/swtrampolines
Instagram: instagram.com/skywalker_trampolines
TABLE OF CONTENTS
Part List.....................................................................................................................................................................................3
Part Identification........................................................................................................................................................4-6
Exploded Drawing.............................................................................................................................................................7
Assembly........................................................................................................................................................................8-20
Maintenance and Care Information....................................................................................................................21
Instructions for Use.....................................................................................................................................................22
Warning Label Placement.......................................................................................................................................23
Instructions and Model Lessons................................................................................................................24-25
Trampoline Safety Information..............................................................................................................................26
EnclosureSafety Information.................................................................................................................................27
Methods of Accident Prevention........................................................................................................................28
Limited Warranty.............................................................................................................................................................29

Key No.
17
18
19
20
21
22
23
24
25
26
27
28
29
#
#
PART LIST
3
ORDERING REPLACEMENT PARTS
We get it... sometimes things happen. But the fun shouldn’t stop just because you need a new bolt or screw! To order
replacement parts, check out our website at: www.skywalkertrampolines.com or call our toll-free Customer Care
Hot-line at 1-866-603-Jump (5867), Monday - Friday, 8 a.m. until 5 p.m. Mountain Time (excluding holidays).
Our customer service team will ask you a few questions in order to get the replacement part sent out as soon as
possible. We’re not trying to complicate your life, we promise.
When calling, make sure to have the following information ready:
• The model # of the product (see the front cover of this manual)
• The key # and description of the part (see the part list above)
• The quantity needed (only you know the answer to that one!)
BEFORE YOU BEGIN
Thanks for choosing Skywalker Trampolines! We’re just as excited as you are to help your family live an active (but
most importantly FUN) lifestyle. This model is one of our favorites, and we’re confident you’ll love it too. To make
things easier for you, we’ve listed important information that you (and your little outdoor adventurers) need to know.
Make sure you brush up on the warnings, instructions, assembly, maintenance, and use of your new product...
because there will be a pop quiz at the end! (Okay, not REALLY, but if you’re still reading this, props to you! You’re
awesome).
Key No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Qty.
4
8
4
8
4
4
8
1
1
80
16
2
4
8
8
8
Qty.
20
12
26
16
16
16
20
40
20
16
8
1
2
1
1
Description
Foam
Strap with D-rings
Self-tapping Screw (2 spare parts)
M10x88mm Bolt
M10 Washer
M10 Nut
M6x70mm Bolt
M6 Washer
M6 Nut
Bolt End Cap
End cap
Spring Tool
Wrench
User Manual & Safety Placard
Set of ASTM Frame Labels
Description
Corner Tube
Straight Tube
Curved Tube
Sockets
Male Leg
Female Leg
Leg Post
Jump Mat
Enclosure Net
Gold Springs
Silver Springs
Frame Pad (2 Pieces)
Top Tube
Top Corner Tube
Upper Tube
Lower Tube

4
Before you begin, take a look at the drawings below to make sure you have all the parts! The numbers in the squares
to the left (key numbers) will help you identify the parts during assembly.
PART IDENTIFICATION
1 2
456
7
3
8
Sockets (x8)
Corner Tube (x4)
Leg Post (x8)
Male Leg (x4) Female Leg (x4)
Jump Mat (x1) 9
10 Gold Spring (x80) 11 12 Frame Pad
(x2 Pieces)
Straight Tube (x8) Curved Tube (x4)
Enclosure Net
Silver Spring (x16)

5
13 14 15
19
16
20
17
21
Top Corner Tube (x8)
Lower Tube (x8)
M10x88mm Bolt (x16)
Foam (x20)
M10 Washer (x16)
18
22 23 24
Upper Tube (x8)
Self-tapping Screw
(x26) (2 Spare Parts)
Strap with D-rings
(x12)
M10 Nut (x16)
Top Tube (x4)
M6x70mm Bolt (x20) M6 Washer (x40)

6
28 29
Spring Tool (x1) Wrench (x2)
Before you begin, take a look at the drawings below to make sure you have all the parts! The numbers in the squares
to the left (key numbers) will help you identify the parts during assembly.
PART IDENTIFICATION
25 M6 Nut (x20) 26 27
Bolt End Cap (x16) End Cap (x8)

7
EXPLODED DRAWING
(1)
(1)
(1)
(1)
(2)
(7)
(23)
(23) (20)
(20)
(21)
(21)
(22)
(22) (26)
(26)
(23)
(23) (24) (24)
(24) (24)
(24)
(24)
(25)
(25)
(25)
(7)
(7)
(7)
(5)
(5) (8)
(10)
(12)
(9)
(16)
(16)
(16)
(16)
(16)
(15)
(15)
(15)
(14)
(14)
(15)
(16)
(15)
(15)
(14)
(14)
(14)
(14)
(13)
(13)
(13)
(18)
(11)
(11)
(6)
(5)
(5)
(6)
(6)
(6)
(4)
(2)
(2)
(4)
(3)
(3)
(3)
(3)
(2)
(2)
(2)
(2)
(2)
(16) (16)
(15)
(15)
(13)
(14)
(14)

READ THIS BEFORE YOU BEGIN
• You’ll probably need at least 2 adults and 2 hours to assemble your trampoline (of course, that depends on what
model you have, and whether or not you’re secretly a superhero).
• We’ve provided a Phillip’s screw driver and two adjustable wrenches to help with assembly, but you’re more than
welcome to use your own tools. Many find that using a power drill and a rubber mallet makes things easier.
• Use gloves to protect your hands from pinch points during assembly. Plus, it’s an up-and-coming fashion trend.
• The assembly steps refer to parts by their descriptions and key numbers (see the part list on page 3).
• The assembly steps are written in a specific order, and if you don’t follow them exactly... you may end up having to
start all over again. We promise we won’t say, “I told you so” but really... we told you so.
• Most importantly... YOU’VE GOT THIS. YOU’RE THE BEST TRAMPOLINE ASSEMBLER AROUND. This may not be the
easiest thing you’ve ever done... but it will be worth it. Trust us.
And if you’re a visual learner, check out our assembly videos!
ASSEMBLY
STEP 2
12
8
STEP 1
Register your trampoline! For info on warranty registration, see page 2.
Visit:youtube.com/c/SkywalkerTrampolines
Corner Tube (x4) Straight Tube (x8) 4Socket (x8)
(4)
(2) (2)
(4)
(1)
Place two straight tubes (2), a corner tube (1), and
two sockets (4) on the ground as shown. Make
sure the spring holes of the straight tubes are
facing the ground. Connect the straight tubes to
the corner tubes. Repeat this step until you have
completed all four sections.

9
ASSEMBLY
STEP 3
20 M10x88mm
Bolt (x16) 21 M10 Nut
(x16) Bolt End Cap (x16)
26
22
M10 Washer
(x16)
(20)
(20)
(20)
(20) (21) (21)
(21)
(21)
(22)
(22)
(22)
(26)
(26)
(26)
(26)
(22)
Place the sockets onto the end of each tube
and line up the holes. Secure using four
M10x88mm bolts (20), four M10 washers (21),
four M10 nuts (22). Then, place four bolt end
caps (26) onto the bolt ends. Repeat this step
until four corner segments are complete.
STEP 4 Insert two leg posts (7) into the
sockets, and secure using two
M6x70mm bolts (23), four M6 washers
(24) and two M6 nuts (25). Repeat
this step until all eight leg posts are
assembled.
723 24 25
Leg Post (x8) M6x70mm
Bolt (x8) M6 Washer (x16)
M6 Nut
(x8)
(23)
(24)
(24)
(23)
(24)
(7) (7)
(24)
(25)
(25)

10
ASSEMBLY
STEP 5
Insert one male leg (5) into one
female leg (6), and secure with
one M6x70mm bolt (23), two M6
washers (24), and one M6 nut (25).
Repeat this step until you have
made four U-shaped leg sections.
5 6
Male
Leg (x1)
Female
Leg (x1) 23 24 25
M6x70mm
Bolt (x4)
M6 Washer
(x8) M6 Nut
(x4)
(5)
(23)
(24)
(24)
(25)
(6)
STEP 6 Insert one U-shaped leg piece into the leg posts of a corner
frame section. Make sure the holes of the U-leg match the
holes of the leg posts. You may need to try more than one
U-leg to find a correct fit. Secure with two M6x70mm bolts
(23), four M6 washers (24), and two M6 nuts (25). Repeat
this step until four corner leg sections are assembled.
23 24 25
M6x70mm
Bolt (x8)
M6 Washer
(x16) M6 Nut
(x16)
(23) (23) (24) (24) (24) (25)
(24) (25)

11
Grab a friend and flip the assembled corner leg sections over so they are
now standing on the legs. (Do not skip this step! We’re not underestimating
your strength or anything, but if you connect before flipping, the entire
frame will be too heavy to flip.) Now place a curved tube (3) (bend facing
out) in between two corner leg sections and slide them together. Repeat on
the other side. You will now have two square frame halves assembled.
Now, place two curved middle tubes (bend facing out) between the two
frame halves.
Slide the two halves of the trampoline together to create a free standing
frame.
STEP 7
3Curved Tube (x2)
STEP 8
3
(3)
(3)
(3)
(3)
Curved Tube (x2)

ASSEMBLY
12
STEP 9
Enclosure Net (x1)
Jump Mat (x1)
8 9
The enclosure net (9) will be pre-installed to the jump mat (8)
(just trying to help you out a bit!) Before continuing, make sure
each V-ring of the jump mat is properly threaded through the
corresponding hole in the enclosure net.
STEP 10
Place the jump mat on the ground inside the frame with the enclosure net on top.
Be sure to center the enclosure door on the middle of one side!
Enclosure door

13
Repeat step 11 to attach two more gold springs to all of the remaining
corners. You now should have eight springs attached, two in each corner.
Next, attach two gold springs to two V-rings on each side of the corner.
Repeat this step on the three remaining corners. You now should have 24
gold springs attached. Note: Be sure you are lining up the correct V-rings
and frame holes!
You may want to use gloves for this step! Using the spring tool (28), hook
the smaller end of a gold spring (10) into the corner square ring. Stretch the
free end of the spring until it reaches the nearest frame hole. Repeat this
step to place another spring into the same corner square ring and nearest
frame hole. Note: The springs will be difficult to stretch. Ask a friendly
neighbor (or stranger) to help!
STEP 12
STEP 11
10
10
Gold
Spring (x2)
Gold Spring
(x22)
28 Spring
Tool (x1)
(28)
Gold springs

ASSEMBLY
14
Place four silver springs in the middle of one curved tube. To make sure
the V-rings and frame holes line up properly, count the number of frame
holes starting from the corner and moving towards the middle curved tube.
Then, count the V-rings starting from the same corner to the exact number
of spring holes and place the springs. Repeat this step on each side to
place a total of 16 additional springs.
Next, attach four additional gold springs on each side of the frame by
placing them on either side of the sockets.
You should now have attached 16 more gold springs (four on each side).
STEP 13
11 Silver Spring (x16)
STEP 14
10
White springs
Gold Spring (x16)

15
Now, working in a clockwise direction, attach all of the remaining gold
springs. Make sure the V-rings and frame holes line up correctly.
(Remember, you’re the boss here. You tell those springs what to do! And
other people if they’re helping...)
STEP 15
10
Lay the two halves of the frame pad (12) on the frame. Make sure to line the
pad up with the frame so the slits sit over the sockets.
Then, connect the two pieces of padding together with the velcro.
STEP 16
12 Frame Pad (x2 Pieces)
Gold Spring (x40)

16
ASSEMBLY
STEP 17
Look under the trampoline. Find the straps that are attached to the underside of the frame pad (12). Position
the strap with buckle so that the strap and buckle is on either side of the frame. Position the inner straps so
that one strap is threaded through a V-ring. Now tie all of the inner straps in bows, and buckle the outer straps.
Secure the corners of the frame pad to the frame by hooking the straps to the D-rings at each corner.
If you want, take a snack break because you’re MORE THAN
HALFWAY DONE, and you deserve it.
This next step is easy. Slide one piece of foam (17) onto one top
tube (13).
13
STEP 18
Top Tube (x1) 17 Foam (x1)
(13)
(17)
Inner strap
Strap with buckle
Underside of trampoline

17
Insert two top corner tubes (14) into the top tube with foam (13) and
secure together using two self-tapping screws (19).
Repeat steps 18-19 three more times to complete four total top tube
sections.
STEP 19
14 19
Top Corner
Tube (x2) Self-tapping
Screw (x2)
(13)
(14)
(14)
(19)
(19)
STEP 20 Insert two upper tubes (15) into the corner tubes, and
secure using two self-tapping screws (19). Then, insert two
lower tubes (16) into the upper tubes, and secure using two
self-tapping screws. Make sure the two indented sides of
the straight tubes are faced inside as shown. Do not tighten
the screws all the way yet.
Upper
Tube (x2)
Lower
Tube (x2)
15 16 19 Self-tapping
Screw (x4)
(19)
(19)
(15)
(16) (16)
(15)
(19)
Side with indent
(19)

18
ASSEMBLY
Next, slide four foam pieces (17) onto the tubes. If you’re having trouble
getting the foam over the tubes, try adding a small amount of water inside
the foam!
Repeat steps 20-21 three more times to complete four total enclosure pole
sections.
STEP 21
17 Foam (x4)
(17)
Insert a strap with D-rings (19) through the small belt sewn on the top edge
of the net. Wrap the end of the strap under and around the foam covered
tube and up through the two D-rings. Thread the end of the strap back
down through the lower D-ring on the strap. Pull the loose end of the strap
to remove any slack, but do not fully tighten the strap yet. Continue to attach
the net to the other top tubes in this same manner.
STEP 22
18 Strap with D-rings (x12)
1
(18)
2
3 4
Top edge
Small belt

19
Use a ladder for this step! Now, fully tighten the straps on each of the arched enclosure poles.
Be careful not to pull too tight or you could rip the foam!
STEP 24
STEP 23
Make sure the indented sides of the straight tubes are against the trampoline frame. Using a couple people
(because the poles are pretty heavy!), grab either side of an enclosure arch. Lift the poles at the same time
and place the end of the lower tubes into the T-sockets. Push the poles all the way down into the sockets.
Repeat this step to install the remaining three arches.
Side with indent

LAST STEP YOU’RE IN THE FINAL HOME STRETCH. Insert the end caps (27)
into the bottom of the sockets.
Tie the included placard to a socket close to the enclosure door as shown.
End Cap (x8)
27
20
STEP 26
Congratulations on completing your new trampoline! (See... we knew you could do it!) So here comes the
real question... are you satisfied with this completed product? If you are, go ahead and write a review on the
retailer’s site you bought it from. We’d really appreciate it... and if we could, we’d give you a gold star. Are you
completely frustrated and have some choice words for us? Contact us directly! We’re not trying to ruin your life,
we promise. And we’ll do everything we can to make it right again. See contact info on page 2-3.
ASSEMBLY
STEP 25
Safety placard