Slant/Fin VICTORY II VHS Series Guide

Models KC-45 and KC-90
USER’S INFORMATION
MANUAL
For Your Safety, Before Operating
The Boiler, Read This Manual
WELCOME TO OUR VALUED CUSTOMER
You are now the owner of a Slant/Fin Prodigy 21
gas-fired boiler, another quality heating product
designed and manufactured by an industry leader,
to provide your family with many years of reliable
comfort and trouble-free performance.
The care and maintenance of your new boiler is
important to prevent a hazardous condition which
might result from lack of proper servicing.
Therefore, you should perform regular “owner”
inspections as described in this manual (and
report any concerns to a qualified service
technician) as well as have your boiler serviced by
a qualified service technician at least once a year,
preferably before the beginning of each heating
season.
LIGHTING INSTRUCTIONS
Locate, read and then follow the procedures on
the lighting instructions label attached to the
boiler. For reference, we have reproduced those
instructions in this manual.
WARNING: If the information in this
manual is not followed exactly, a fire
or explosion may result causing
property damage, personal injury or
loss of life.
- DO NOT store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
- WHATTO DO IFYOU SMELL GAS
• DO NOT try to light any appliance.
• DO NOT touch any electrical switch;
DO NOT use any phone in your
building.
• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
• If you cannot reach your gas
supplier, call the fire department.
- Installation and service must be
performed by a qualified installer,
service agency or the gas supplier.
This manual must be left with owner, hung on
or adjacent to the boiler. Owner should retain
manual for future reference
PUBLICATION P-UIM Rev. C
Residential • Gas-fired • Hot Water Boilers
®
®
Printed in USA 396
Part No. 65-0647

®
2
At least once each month during the heating
season, perform the following inspections:
Check Vent Tubing: Look for leakage at joints and
sagging of vent tubing runs. If evident, call a qualified
service technician.
Check Vent Terminal (Outside): Look for and remove any
obstructions (i.e. leaves, shrubs, snow).
Check Water Piping: Look for leaks around boiler and at
all joints. If evident, call a qualified service technician.
Check System Water Pressure: The temperature/pres-
sure gage indicates the pressure in the boiler for each
water temperature. For most installations, it should
indicate about 12 psi to 15 psi for 70° to 100° water
temperatures and from 15 psi to 25 psi for temperatures
up to 240°. Ask your installer or service technician to
explain and show you what normal pressures to look for.
If pressure decreases from normal, the system is losing
water; if pressure increases from normal, the boiler relief
valve will open to relieve pressure (water will be evident
on floor below relief valve discharge piping). In either
case, call a qualified service technician.
At least once a year, check the air filter: Replace it
(recommended) or clean it. For access to the filter,
remove boiler front cover by pushing down on top center
portion of cover until support clip releases cover at top,
then lift off of support clips at bottom of cover.
Open air filter box cover by rotating the 1/4 turn fastener
on top of cover, then swing open at hinge.
Slant/Fin replacement air filter, part number 65-0524,
must be used. The filter can be cleaned with soap and
water. Shake off excess moisture before replacing.
In the case of severe outside dust/dirt conditions which
cause above-average accumulation on the filter, it may
be necessary to change it (or clean it) more often. This
procedure may be done by user or service technician,
providing a record is kept of each replacement or
cleaning date to assure an established diligent routine.
TAKING CARE
OFYOUR BOILER

ANNUAL TECHNICIAN INSPECTIONS
Before each heating season, call your qualified
service technician to perform the following
inspections (and repair any problems encountered).
Check Vent System: For corrosion, obstructions, leaks
or sagging. Will require disassembling and resealing of
vent tubing.
Check Water System: For water piping leaks, properly
filled boiler and proper system air elimination.
Check Gas Piping: For gas valve and piping leaks.
Check Boiler Controls: For correct settings and
functioning. To include safety controls and calibration.
Check Air Filter: Replace (recommended) or clean.
System Heat Exchanger and Burner: For sooting,
corrosion or improper operation.
Blower and Circulator: Sealed components which do
not require lubrication.
The PRODIGY 21 control light panel has a complete set
of LED indicator lights which provide important
information at a glance about boiler operation:
Power Indicator (RED): Steady ON means there is
electrical power to the boiler. Light will come on when
power is provided to boiler.
Diagnostic Indicator (RED): Steady ON or intermittent
flashing indicates a system operation problem.
Full Input Indicator (AMBER): Steady ON means the
boiler is running in high-fire mode. Light will come on
when boiler starts up; will go off when the boiler enters
the low-fire mode or shuts off.
Reduced Input Indicator (GREEN): Steady ON means
boiler is running in low-fire mode. Light will come on
when the boiler automatically switches to the fuel-
saving low-fire mode; will go off when boiler returns to
high-fire mode or shuts off.
WHAT THE INDICATOR
LIGHTS TELLYOU
Before calling a qualified service technician, check
the following first:
• Room thermostat is calling for heat?
• Fuse or circuit breaker is OK?
• Boiler service switch is ON?
• Gas supply is available to gas meter?
• Manual main gas shutoff is open?
• Boiler gas control arm is in ON position?
Then, observe indicator lights: You can help provide
useful information to the service technician so the
technician can arrive with appropriate replacement parts.
Carefully note the red diagnostic indicator light. When a
system failure occurs, and there’s power to the boiler,
the indicator light will show a series of quick flashes.
There will be a short interval between the series when
the indicator stops flashing.
Count the number of flashes that occur after the short
no-flashing interval. Using the chart above, determine
correct failure code for number of flashes you counted.
Call a qualified service technician and report your boiler
model plus the number of flashes you counted and the
code for the flashes.
Note: The boiler will attempt restart each hour and after
a power interruption. If boiler restarts, diagnostic light
will turn OFF. If boiler does not restart, diagnostic light
will return to either steady-on or the series of flashes.
IN CASEYOUR
BOILER SHUTS DOWN
BOILER FAILURE CODES
Continuous Flashing-- Electronic Control Failure
1 Flash ------------------- High Limit Open 1 Hour
2 Flashes ---------------- No Ignition
3 Flashes ---------------- Pressure Switch Open
4 Flashes ---------------- Hot Surface Ignitor Failure
5 Flashes ---------------- Blower RPM Too Low
6 Flashes ---------------- Low Water Cutoff Open
7 Flashes ---------------- Improper Flame Signal
Steady ON -------------- Loss Of Flame Signal
3
®

FORYOUR SAFETY READ BEFORE OPERATING
FORYOUR SAFETY READ BEFORE OPERATING
A. This appliance does not have a pilot. It is equipped with an
ignition device that automatically lights the burner.
DO NOT try to light the burner by hand.
B. BEFORE OPERATING smell all around the appliance area
for gas. Be sure to smell next to the floor because some
gas is heavier than air and will settle on the floor.
WHAT TO DO IFYOU SMELL GAS
• DO NOT try to light any appliance.
• DO NOT touch any electric switch; DO NOT use any
phone in your building.
• Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire
department.
C. Use only your hand to turn the gas control selector arm.
NEVER use tools. If the selector arm will not move by
hand, DON'T try to repair it, call a qualified service
technician. Force or attempted repair may result in a fire or
explosion.
D. DO NOT use this appliance if any part has been under-
water. Immediately call a qualified service technician to
inspect the appliance and to replace any part of the control
system and any gas control which has been underwater.
•STOP! Read the safety information above on this label.
• Set the room thermostat to lowest setting.
• Turn off all electric power to the appliance.
• This appliance is equipped with an ignition device which
automatically lights the burner. DO NOT try to light the
burner by hand.
• Remove boiler front cover.
• Depress and move gas control selector arm left to
“OFF” position. Note: Arm cannot be turned to “OFF”
unless arm is pushed in slightly. DO NOT force.
• Wait five (5) minutes to clear out any gas. Then smell for
gas, including near the floor. If you smell gas, STOP!
Follow "B" in the safety information above on this label. If
you don't smell gas, go to the next step.
• Depress and move gas control selector arm right to
“ON” position.
• Replace boiler front cover.
• Turn on all electric power to the appliance.
• Set room thermostat to desired setting.
• If the appliance will not operate, follow the instructions “To
Turn Off Gas To Appliance” and call your service
technician or gas supplier.
TO TURN OFF GAS TO APPLIANCE
• Set room thermostat to lowest setting.
• Turn off all electric power to the appliance if service is to be
performed.
• Remove boiler front cover.
• Depress and move gas control selector arm left to
“OFF” position.
• Replace boiler front cover.
Your boiler must be installed, serviced and repaired
by a qualified service technician only. Owner must
not attempt to install, service or repair this boiler.
Should overheating occur or the gas supply fail to
shut off, DO NOT turn off or disconnect the
electrical supply to the pump. Instead, shut off the
gas supply at a location external to the appliance.
DO NOT use this boiler if any part has been under-
water. Immediately call a qualified service
technician to inspect the boiler and to replace any
part of the control system and any gas control
which has been underwater.
DO NOT attempt to add water to boiler or system.
An automatic water feed should have been installed
(based on local codes) to maintain proper water
level; ask your installer if this device was installed.
Keep boiler area clear and free from combustible
materials, gasoline and other flammable vapors and
liquids.
DO NOT store anything against the boiler or let
anything accumulate in area surrounding the boiler.
DO NOT allow anything to accumulate around or
block air flow at outside vent terminal (i.e. leaves,
shrubs, snow).
For closet installations, DO NOT allow anything to
block air flow at closet ventilation air openings.
DO NOT use water from heating system for
cleaning.
DO NOT place clothing on the boiler or venting
system to dry.
WARNING: If you do not follow these instructions
exactly, a fire or explosion may result causing
property damage, personal injury or loss of life.
SLANT/FIN CORPORATION, Greenvale, N.Y. 11548 • Phone: [phone]
FAX: [phone] • Canada: Slant/Fin LTD/LTEE , Mississauga, Ontario
www.slantfin.com
®
LIGHTING INSTRUCTIONS
OPERATING INSTRUCTIONS
4
OFF
ON
Selector
Arm
Gas Valve 7200 DERN
IMPORTANT SAFETY
INFORMATION FOR YOU
®