SLI SECO-LARM ENFORCER EV-2166-N3WQ User manual

Manual
Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant.
Mid-Size Vandal Dome Camera
EV-2166-N3WQ
480 TV lines
3.6mm
EV-2166-NVWQ
480 TV lines
4~9mm varifocal
EV-2766-N3WQ
600 TV lines
3.6mm
EV-2766-NVWQ
600 TV lines
4~9mm varifocal
EV-2166-P3WQ
480 TV lines
3.6mm
EV-2166-PVWQ
480 TV lines
4~9mm varifocal
EV-2766-P3WQ
600 TV lines
3.6mm
EV-2766-PVWQ
600 TV lines
4~9mm varifocal
Model No.
Resolution
Lens Size
NTSC
PAL

SECO-LARM Mid-Size Vandal Dome Cameras
2SECO-LARM U.S.A., Inc.
NTSC
2166-N3WQ
2166-NVWQ
2766-N3WQ
2766-NVWQ
PAL
2166-P3WQ
2166-PVWQ
2766-P3WQ
2766-PVWQ
Type
Mid Size Vandal Dome
CCD
1/3” Sony Super HAD II
Resolution
480 TV lines
600 TV lines
Lens
3.6mm
4~9mm
3.6mm
4~9mm
# of IR LEDs
18 (850nm)
IR range
65ft (20m)
Pickup elements
510x492 pixels (NTSC)
500x528 pixels (PAL)
768x494 pixels (NTSC)
752x582 pixels (PAL)
Sync
Internal
Video output
1Vp-p composite video, 75Ω
Minimum illumination
0-lux (LEDs ON)
S/N ratio
>48dB
Shutter control
Auto Electric Shutter (AES)
Gain control
Auto
White balance
Auto
Operating voltage
12VDC ±10%
Current draw
100mA (LEDs OFF), 200mA (LEDs ON)
IP Rating
IP65
Operating temperature
-4°~122° F (-20°~50° C)
Dimensions
41/4”x31/2” (108x89 mm)
Weight
18-oz (500g)
Dimensions:
Parts List:
Specifications:
3 x Mounting screws
3 x Screw anchors
1 x DC plug with terminal block
1 x Allen wrench
1 x Manual
1 x Camera
Adjusting the 3-Axis Gimbal:
Move the camera vertically, horizontally, or
rotate the lens to change the lens angle.
41/4”
(108mm
)
31/2”
(89mm)

SECO-LARM Mid-Size Vandal Dome Cameras
SECO-LARM U.S.A., Inc. 3SECO-LARM U.S.A., Inc. 33 3
1. Please read this manual carefully and keep it for
future reference.
2. Use the camera within given temperature and
electricity limits.
3. Do not point the camera at the sun. Heat could
damage the camera, even when not in use.
4. Do not mount the camera in areas exposed to
radiation, strong magnetic fields, or strong
electrical signals*
5. Do not drop the camera or subject it to strong
vibrations.
Note: Many video monitors produce strong
electromagnetic fields close to the display CRT,
especially when the monitor is turned on or
during de-gaussing, which occurs automatically
with many monitors when turned on.
Before Starting:
1. Undo the 3 set screws on the side of the dome
cover using the included allen wrench.
2. Remove the dome from the base.
3. Temporarily connect the camera’s female BNC
connector to a monitor.
4. Temporarily connect the camera’s DC jack to a
12VDC power supply.
5. Hold the mounting base with your hand against the
wall, ceiling, or other mounting surface. Try
various locations and angles while watching the
monitor to find the location that offers the best
protection. Mark that location with a pencil
6. If the installation involves surface wiring, use the
wiring notch located on the side of the mounting
base to run wires.
Installation:
7. Mount the mounting base to the wall using the
3 included mounting screws. If necessary, use
the included screw anchors.
8. Run a hidden, permanent video cable from the
monitor to the camera.
9. Run a hidden, permanent power cable from a
12VDC power supply to the camera.
10.Make any necessary adjustments to the camera
angle by gently twisting the camera on its axis.
11.Reattach the dome to the camera base by giving
the dome a slight twist.
12.Use the included allen wrench to tighten the set
screw, securing the dome to the base.
13.Test the camera again under the exact lighting
conditions under which it is expected to be used.
Overview:
Important:
Do not cut the DC jack or the female
BNC connector as this will void the warranty.
DC plug with
terminal block
Dome cover
DC jack
Mounting screw
Set screw
Female BNC connector
Camera
Mounting base
Wiring notch

SECO-LARM Mid-Size Vandal Dome Cameras
4SECO-LARM U.S.A., Inc.
MiEV-2x66-xxWQ_1011 - 480_600TVL.docx
PICSN4
IMPORTANT
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this
product in violation of any current laws or statutes.
WARNING
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not open
the case of this device, as there are no field-serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to
part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his or her own expense.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a
period of one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of
any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is
not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or
property damages of any kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is
one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without
notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2012 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part,
without the written permission of SECO-LARM.
SECO-LARM U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Tel: [phone]
Website: www.seco-larm.com
E-mail: [e-mail]
The screen is blank.
The screen image is dim
The screen image has poor contrast.
The screen image flickers.
The screen image is distorted.
The camera case is hot.
IR LEDs do not turn on.
Check that the camera is powered up.
Check that the power supply’s polarity is correct.
Check that the monitor is powered up.
Check that the video cable connecting the camera to the
monitor is connected properly.
Clean the lens using a soft, clean cloth.
Check that the light source is adequate.
Adjust the monitor’s contrast knob.
Change the position of the camera.
Change the position of the camera.
Change the position of the camera.
Check that the correct power supply is in use.
Check that the correct power supply is in use.
Troubleshooting: