Smart openers Smart slider User manual

Smart Slider

Sliding Gate Opener

WARNING: IT IS VITAL FOR THE SAFETY OF ALL

PERSONS INSTALLING AND USING THIS OPENER TO

FOLLOW THE INSTALLATION INSTRUCTIONS AND

SAFETY WARNINGS. FAILURE TO COMPLY MAY RESULT

IN SERIOUS PERSONAL INJURY AND/OR PROPERTY

DAMAGE AND FAILURE OF THE OPENER SYSTEM.

INSTALLATION MANUAL

Index

Contents

Important Safety Warnings

Product Description

Operating Controls

Mechanical Installation

Foot Print

Electrical Connection

Quick Reference Guide

Coding Transmitters

Deleting Transmitters

Transmitter Button Allocation

Setting Limits- Single Leaf

Setting Limits- Dual Leaf

Setting Pedestrian Mode

Setting Lock Mode

Setting Obstruction Force Margin

Setting Motor Open/Close Speed

Setting Gate Lead Time Delay

Setting Photo Beam Mode

Setting Auto-Close Mode

Setting Auto-Close Timer Delay

Manual Disengagement

Important Information for the User

Maintenance

Final Notes

Technical Specications

Warranty

To the extent that they may be lawfully excluded, Smart Openers Pty Ltd hereby expressly excludes all conditions and

warranties, statutory or otherwise, which may be implied by law as conditions or warranties of purchase of a Smart

Openers Pty Ltd gate opener. Smart Openers Pty Ltd hereby further disclaims and rejects to the maximum extent

permitted by law any liability or responsibility whatsoever for any direct, indirect, consequential, incidental or other injury,

damage, cost, expense or loss whatsoever incurred or suffered by any person, company, rm or organization as a result

of any failure to install the gate opener in accordance with these installation instructions.

No part of this publication may be reproduced, utilised, transmitted, or distributed in any form by any means including

photocopying, recording, mechanical, electronic or otherwise by any party, without the written permission from the publisher

Smart Openers Pty Ltd. Copying without authorisation is ILLEGAL.

-3-

Important Safety Warnings

The Smart Slider gate opener described in this manual

is designed for the automation of residential track or

cantilever type sliding gates. Any other use is considered

improper and will void the warranty.

SAFETY WARNING:

You are carrying out operations on machine systems

classied in the automatic gates and doors category and

as such failure to comply with the relevant safety rules

may result in serious personal injury and/or property

damage. Reference to the safety rules can be found on

pages 2-4 of the owners manual and should be read and

understood prior to installation.

Only qualied personnel should install and service the

equipment. It is the responsibility of the installer to adhere

to all relevant safety standards.

The Smart Slider opener is designed and manufactured

to meet all current Australian standards and it is

essential that the installer also installs the equipment in

accordance with all local and Australian regulations.

Unqualied personnel or those who do not know the

occupational health and safety standards applicable

to automatic gates and doors category must under

no circumstances carry out installations or implement

systems.

Persons who install or service the equipment without

observing all the applicable safety standards will be

held responsible for any damage, injury, cost, expense

or claim whatsoever suffered by any person as a result

whether directly or indirectly from failure to install the

system correctly and in accordance with the relevant

safety standards and installation manual.

For a more detailed list of the Safety Warnings and safety

issues associated with the installation and use of a Smart

Slider gate opener refer to the safety warnings in the

OWNERS MANUAL.

No Package Part

1 Motor No Description Qty Remark

1 Motor 1 Set

2 Transmitter 2 Pcs Smart Pet Transmitter

3 Limit Cam 2 Pcs

4 Fixing Hardware 1 Set For Limit Cams

5 Installation Manual 1 Pc

6 Owners Manual 1 Pc

7 Quick Start Guide 1 Pc

Contents

Description

The Smart Slider gate opener requires a 240V AC 50Hz

power input. The 24V DC motor can provide remote

control and automatic modes for operation. When the

gate is in operation, movement can be interrupted by

activation of the safety inputs (transmitter, wall switch (if

tted) and photo beams (if tted).

An encoder sets open and close positions and braking

during the end of the travel cycle reducing speed and

noise.

A 433.22MHz radio receiver is built into the circuit board

and the rolling code is memorised with the self-learning

technique. As an alternative to the built-in receiver the

unit will accept any of the range of stand alone radio

receivers. The unit has been designed to provide

maximum reliability, safety and exibility of use.

IMPORTANT:

Before starting to install the unit read all of the

instructions carefully and make sure you are familiar

with the safety warnings included in this manual and

in the OWNERS MANUAL.

-4-

Operating Controls

1. CODE Button - for coding transmitters.

2. PB Button - Open/Stop/Close.

3. MODE Button - Save setting and exit to normal

operation mode.

4. MENU Button - Function/Peramater select.

5. SET Button - Save changes and move to next

function.

Circuit Board Connectors

6. Connector for motor 1.

7. Connector for motor 2.

8. Connector for backup battery.

9. Connector for encoders (not used on Slider).

10.Connector for controlling inputs.

11. Connector for motor mechanical limits input.

12. Connector for photo electric beams.

13. Connector for solenoid/magnetic lock.

14. Connector for DC ashing light or similar (5A max).

15. Connector for DC courtesy light or similar (5A max).

16. Connector for solar panel or external DC charger.

17. Connector for controller power from transformer.

Smart Openers

SC Vx.xx

1 2 3 4 5

6 7 8

Com

Push Btn

Pedestrian

Stop

Open

M2 Open Limit

Com

M2 Close Limit

M1 Open Limit

Com

M1 Close Limit

Com

Photo Beam 2

Photo Beam 1

+24V

Lock +

Lock -

Activity 2 +

Activity 2 -

Activity 1 +

Activity 1 -

DC Charger -

DC Charger +

24V AC IN

Encoder 2

Encoder 1

Encoder 2 Encoder 1

Motor 1 Motor 2

24V Battery

Back Up

RS-232

Interface for site

maintenance

Smart Openers

SC Vx.xx

RF Receiver

-5-

Installation

Remember: There are specic standards that have

to be strictly followed regarding the safety of electrical

installations and automatic gates and doors.

As well as the legal requirements and standards that

must be adhered to, please take note of the following

points to ensure maximum safety and reliability of your

installation.

1. Prior to installing check the surrounding environment.

Carefully evaluate any hazards there could be from

physical damage (transiting vehicles, parts of trees

falling etc.), possible contact with foreign bodies

(insects, leaves, etc.), Flooding hazards or any other

exceptional events.

2. Check that the mains voltage is the same as that

given on the rating plate and in this manual.

3. Check that there is suitable electrical protection

against short circuits/power spikes and proper

earthing on the mains supply.

Remember: The unit has mains voltage running through

it (electrocution hazard, re hazard, etc).

4. Take care with the control unit; parts may be subject

to damage if abused.

5. Make sure you have all the necessary materials and

that they are suitable for this kind of use.

6. Read all the instructions thoroughly and make sure

they are understood before attempting to install the

Smart Slider.

7. Before starting the installation, carefully analyse all

the risks relating to automating the gate. Verify that

the gate to be automated is in a sound condition

and that the mechanisms are in good working order;

observe the safety margins and minimum distances.

8. Evaluate with particular care the safety devices to be

installed and where to install them; always install an

emergency stop device for interruption of power to the

opener if required.

9. Once the risks have been analysed, install the Smart

Slider opener and relative safety devices, emergency

stop and/or photoelectric cells.

Important: For additional safety Smart Openers Pty Ltd

strongly recommends the tting of Photo Electric safety

beams on all installations.

10.When installing the Smart Slider opener, strictly follow

all the instructions given in the instruction manual. If

some points or procedures in this manual are not very

clear do not install the unit until all doubts have been

cleared up with our technical department.

Pictured above is a typical LEFT HAND installation (from

inside the driveway looking out). Refer to the above

diagram for recommended installation.

1. Smart Slider gate opener

2. Power outlet

3. Gate rack

4. Limit stop cam

5. Photo electric beam (RX/TX type)

6. Digital entry keypad

7. 24V DC ashing light (optional)

3 4

-6-

Foot Print

Use the diagram below as an indication for the

opener footprint to plan your base.

255

285

126 51155

POWER CABLE

GLAND

AUXILLARY

CABLE CAVITY

100

Installation

1. Read the instructions carefully.

2. Install a 240V, adequately protected 3-pin socket near

where the Smart Slider opener is going to be installed

3. Make sure the gate and fence structure is solid and

suitable to be motor driven. A strong base on the gate

is required for securing the rack and an appropriate

concrete slab or similar surface for the Smart Slider

opener.

4. Make sure that when the gate is moving there are no

friction points.

5. The gate must be properly balanced and must be

easily moved by hand..

Positioning The Opener

1. Measure the width of the rack (Smart Openers rack is

40mm) If using third party rack make sure it is Module 4.

2. Move the gate to the desired open position. Position

the opener approximately 150mm from the leading

edge and parallel to the gate and make sure that the

pinion gear is aligned with the rack (Fig. 1).

3. Mark the position of the xing holes and secure with

8mm or 10mm loxins or dynabolts (Fig. 2).

Fixing The Rack

1. With the gate in the desired open position place a

section of rack to mesh with the pinion gear and mark

the xing holes. The rack should start about 25mm

from the edge of the gate (Fig. 2).

2. Repeat the above for the entire length of the gate.

3. Ensure that all rack sections mesh together for

smooth operation.

Fixing The Limit Cam

1. Disengage the opener by releasing the key latch and

moving the manual release arm out at a 90° angle.

2. Move the gate to the desired open position. Place a limit

cam on the rack so that it just triggers the limit switch.

Make sure the cam is facing toward the opener, not

away (Fig. 3).

3. Mark this position and secure the limit cam to the gate

rack.

4. Move the gate to the desired closed position and

repeat as above. Make sure the cam is facing toward

the opener, not away.

WARNING: Make sure the gate has

mechanical stops tted to prevent

the gate rolling out of its guides

when in manual operation. Failure to follow

this warning may result is serious personal

injury and/or property damage.

Antenna

The Smart Slider’s RF receiver features an integrated

antenna in the receiver board. There should be no need

for an external antenna.

Fig. 1

Fig. 2

RACK

PINION

ALIGN TEETH

OF PINION

AND RACK

Fig. 3

-7-

-8-

Electrical Connection

Single Leaf Gate Set Up

For single leaf gate the opener is prewired ready for set

up. Continue to page 9 for set up procedure.

Motor Connection for Two Leaf Gate

For a two leaf gate a master and slave drive unit is

required with connection via a 5-core cable. Connect

5-core cable from the terminal block on Motor 2 to Motor

1 controller as per wiring diagram (Fig. 4).

Ensure that the cable is properly protected with a cable

gland at each end and a suitable conduit across or under

the driveway.

M1 acts as the Master controller and is prewired ready to

go. No cable connections need to be modied for motor

control and limits.

Note: During limits set up (page 12) you must specify on

which side M1 is positioned.

Fig. 4

Com

Push Btn

Pedestrian

Stop

Open

M2 Open Limit

Com

M2 Close Limit

M1 Open Limit

Com

M1 Close Limit

Com

Photo Beam 2

Photo Beam 1

+24V

Lock +

Lock -

Activity 2 +

Activity 2 -

Activity 1 +

Activity 1 -

DC Charger -

DC Charger +

24V AC

Encoder 2 Encoder 1

Motor 1 Motor 2

24V Battery

Back Up

Smart Openers

SC Vx.xx

RF Receiver

-9-

Powering Up

1. Inspect the power cable for damage. Ensure that the

cable will not interfere with the moving gate or the

drive unit.

2. Connect to power. The opener will perform a software

check before displaying the rmware version (Fig. 5).

3. The LCD will then display Positions Not Set (Fig. 6).

Menu Navigation

lUse the CODE button to cycle up through menu

preferences and parameters.

lUse the MENU button to cycle through menu

preferences and parameters.

lPress the SET button to conrm selection and move to

the next menu item.

lPressing MODE at any time will store changes and exit

to main screen. To enter set up again press SET.

Menu Quick Reference Guide

Use the table below as a reference to guide you through

the menu system and parameters.

Menu Item Factory Default Options

1 Installation Right Hand Right/Left

2 Motor Single Motor Single/Dual

3 Pedestrian Mode Off On/Off

4 Lock Pulse Pulse/Hold (Magnetic)

5 Obstruction Setting 03 00 – 09

6 Open Speed 80% 50%-100% (by 5%)

7 Close Speed 50% 50%-100% (by 5%)

8 Motor Delay On (only for Dual Motor) On/Off

9 Photo Beam Off On/Off

9.1 PE Close Off (only for Photo Beam Mode) On/Off

9.2 Sequence Mode Off (only for Photo Beam Mode) On/Off

10 Auto Close Off (only for Photo Beam Mode) On/Off

10.1 Time Delay 30 secs 5-400 secs

10.2 PED Close Off On/Off

10.3 PED Time Delay 30 secs 5-400 secs

11 Transmitter Button PB=1 PD=4 PB, PD, OP, CL

12 Hands Free Learn On On/Off

13 Power Save Mode On On/Off

Smart Openers

SC Vx.xx

Positions

Not Set

Fig. 5

Fig. 6

-10-

Coding Transmitters

Note: The button you choose (1-4) for the rst TX you

code will be the same button for all subsequent

transmitters. Up to 200 TXs can be stored into

memory. If more than 200 are stored the system

will disregard any attempts to code new TXs.

1. Press the CODE button the display will show Code

Learn (Fig. 7).

2. Choose which transmitter button will operate the door

and press that button twice.

The rst press will allocate a number to the remote

and the display will show Remote XXX (Fig. 8), on the

second press the display will show Code Set. Test the

transmitter - the opener will beep to conrm.

Repeat the above steps to code additional transmitters.

Remote TX Coding (Hands Free Learning)

Coding new transmitters via an already coded remote

without being in contact with the control panel is useful

if more than one device is operated by the transmitter. It

also takes the guess work out of button allocation as this

is done automatically.

1. Ensure Hands Free Learning is enabled (page 15).

2. Press TX Button 3 + 4 together for 2 seconds. The

opener will beep to signal Code Learn Mode.

3. Press any button on new transmitter twice (Fig. 9).

The opener will beep to conrm code learned.

Deleting One Transmitter

This is useful if the transmitter is lost and the transmitters

reference number is known.

1. Press and hold CODE for 5 seconds. The LCD will

display Del Remote All.

2. Press SET to scroll up or PB to scroll down to the

desired transmitter number - Remote 023.

3. Press and hold CODE for 3 secs to conrm. The

stored code has now been deleted.

Deleting All Transmitters

1. Press and hold CODE for 5 seconds. The LCD will

display Del Remote All.

2. Press and hold CODE for 3 secs to conrm. All stored

codes have now been deleted.

Transmitter Button Allocation

Note: The following procedure alters these settings for ALL

coded transmitters.

1. Press MENU for 3 secs. Press SET to cycle through

to Transmitter Allocation menu (Fig. 11). The LCD will

display functions on the rst line and button allocation

on the second.

2. Press PB to cycle through buttons 1–4 (0 to disable).

Note: To allocate ALL BUTTONS to the same function

press and hold PB until display show All.

3. Press MENU to allocate the button and move to the

next function and repeat as required.

4. Press MODE to save and exit to normal operation.

Note: If a button is already allocated to one function it will

not be available for any other.

Remote 001

Del Remote

All

PB PD OP CL

01 02 00 00

Fig. 9

Existing

Remote

Uncoded

Remote

Code Learn

Fig. 7

Fig. 8

Fig. 10

Fig. 11

-11-

Setting Left Hand/Right Hand Installation

Note: Make sure that limit cams are installed and in the

desired open and closed positions.

1. Open the gate approximately half way, make sure that

the drive motor is engaged.

2. Press SET for 3 secs to enter set up. The display will

show Right Hand Installation (Fig. 12) (default). If

this is correct press SET to conrm.

OPTION: To change to Left Hand Installation, press

MENU then press SET to conrm.

3. The display will show Single Motor (Fig. 13) (default).

Press SET to conrm.

Setting Limits

Note: Press MENU to abort limits set up at any time.

1. The display will show Motor 1 Set Up (Fig. 14). Press

a coded TX button or PB.

2. The gate will automatically open until the open limit

cam is reached then close until the closed limit cam is

reached. Then the gate will perform a full open/close

cycle to measure force margin, ending in the closed

position.

3. Display will show Set Up Complete (Fig. 15). After 5

secs the display will change to normal operation.

Aborting Limits Set Up

To abort limits set up whilst in progress – press MENU.

To return to set up mode press SET for 3 secs and repeat

initialising procedure as per above.

Resetting Limits

If you are not happy with the limits positions – reposition

the limit cams, then press SET again for 3 secs and

repeat procedure as per above.

Setting Limits – Single Leaf Gate

Fig. 13

Right Hand

Installation

Motor 1

Set Up

Complete

Single

Motor

Fig. 12

Fig. 14

Fig. 15

-12-

Setting Limits – Dual Leaf Gate

Dual Motor Selection

Note: Make sure that limit cams are installed and in the

desired open and closed positions.

1. Open the gate leafs approximately half way, make

sure that the drive motors are engaged.

2. Press SET for 3 secs to enter set up. The display will

show Right Hand Installation (Fig. 16) (default). If

this is correct and MOTOR 1 (the Master Drive Unit

with the control board) is on the right press SET to

conrm.

OPTION: To change to Left Hand Installation, press

MENU then press SET to conrm.

3. The display will show Single Motor (Fig. 17) (default).

Press MENU to change to Dual Motor then press

SET. The display will show Motor 1 Set Up (Fig. 18).

Setting Limits

Note: Press MENU to abort limits set up at any time.

1. Press a coded TX button or PB once. Motor 1 will

automatically open, close and then reopen to record

limit cam positions. M1 will pause in the fully open

position.

2. The display will show Motor 2 Set Up (Fig. 19). There

is no need to press any buttons. M2 will record limit

cam positions and pause in the fully open position.

3. Then the gate will perform a full cycle to measure

force margin. Both leafs will close, open and return to

the closed position.

4. The display will show Set Up Complete (Fig. 21).

Note: Gate leaf delay will be automatically preset at this

time.

Aborting Limits Set Up

To abort limits set up whilst in progress – press MENU.

To return to set up mode press SET for 3 secs and repeat

initialising procedure as per above.

Resetting Limits

If you are not happy with the limits positions – reposition

the limit cams, then press SET again for 3 secs and

repeat initialising procedure as per above.

Right Hand

Installation

Motor 1

Set Up

Dual

Motor

Motor 2

Set Up

Set Time

Delay

Set Up

Complete

Fig. 16

Fig. 18

Fig. 17

Fig. 19

Fig. 20

Fig. 21

-13-

Setting Pedestrian Mode

Pedestrian Mode allows the gate to open partially (or

only one leaf) to allow a person to enter without the need

to open the gate fully as for vehicular access (Factory

Default = Off).

1. Press MENU for 3 secs then SET to cycle though to

Pedestrian Mode.

2. Press MENU to choose On or Off as required.

3. Press SET to conrm or MODE to save and exit.

Note: Pedestrian Mode is factory set to Transmitter

Button 4.

Setting Lock Mode

Lock Mode allows the gate to utilise to be locked with a

magnetic (hold) or pulse lock for added security. The gate

controller releases the lock momentarily before the gate

commences an open cycle (Factory Default = Pulse).

1. Connect lock to terminal block as per Fig. 23.

2. Press MENU for 3 secs then SET to cycle though to

Lock.

3. Press MENU to choose either Pulse or Hold as

required.

4. Press SET to conrm or MODE to save and exit.

Note: Pulse Mode output for 1 sec prior to motor start.

Hold Mode output 24V once motor has stopped.

Setting Obstruction Margin

The Obstruction Force Margin sensitivity is extremely

important for user safety. Make sure that where possible

the minimum (or default) force required to allow the

gate to travel without phantom reversing is used. Smart

Openers strongly recommend that the gate is properly

serviced rather than increasing the force margin to

compensate (Factory Default = 03).

1. Press MENU for 3 secs then SET to cycle though to

Obstruction Margin.

2. Press MENU to cycle through from 00 – 09.

3. Press SET to conrm or MODE to save and exit.

Testing Obstruction Margin

1. Test the obstruction force margin sensitivity by placing

a piece of timber approximately 100mm thick between

the gate and the fence post.

2. Close the gate onto the timber. If the gate does not

reverse easily and attempts to continue to close

adjust the force margin as per procedure above.

LEARN

P/B MODE MENU SET

M2 Open Limit

Com

M2 Close Limit

M1 Open Limit

Com

M1 Close Limit

Com

Photo Beam 2

Photo Beam 1

+24V

Lock +

Lock -

Fig. 23

Pedestrian

Mode On

Obstruction

Margin 03

Fig. 22

Fig. 24

-14-

Setting Motor Open and

Close Speeds

The opening and closing speed can be varied in 5% steps

from 50% -100% to suit the site. This function is useful if

the gate is situated on an incline where gravity increases

closing speed. (Factory Default = 80% Open, 50% Close).

Note: Close speed can only be modied if a Photo Electric

Safety Beam is tted. See Setting Photo Beam

instruction below.

1. Press MENU for 3 secs then SET to cycle though to

Open Speed or Close Speed as required.

2. Press MENU to cycle through from 80% down to 50%

in steps of 5%. Once 50% is reached the next press

of the MENU button will return to 100%.

3. When desired speed percentage is reached press

SET to conrm or MODE to save and exit.

Setting Gate Leaf Time Delay

Note: Only available in dual motor mode.

If required Motor 1 can be set to open before and start to

close a preset time after Motor 2.

(Factory Default = On).

1. Press MENU for 3 secs then SET to cycle though to

Motor Delay.

2. Press MENU to choose Off.

Note: Smart Openers recommends that Gate Delay

remain on.

4. Press SET to conrm or MODE to save and exit.

Setting Photo Beam Mode

Note: A functioning photo electric safety must be installed

and Photo Beam Mode set to ON to enable auto-

close function. Power Save Mode must be set to

OFF see page 15.

Photo Beam Mode allows the gate to close once the

beam has been tripped and restored. Smart Openers

strongly recommend the installation of a PE safety beam

to protect persons and property (Factory Default = Off).

1. Connect PE beam cable to controller terminal black

as per Fig. 28.

2. Press MENU for 3 secs then SET to cycle though to

Photo Beam.

3. Press MENU to choose On.

4. Press SET to conrm or MODE to save and exit. Fig. 28

Open Speed

80%

Close Speed

50%

Motor Delay

Photo Beam

Fig. 25

Fig. 26

Fig. 27

Fig. 29

Com

PE 2

PE 1

+24V

-15-

Setting Auto-Close Mode

Auto-Close Mode allows the gate to close automatically

once the PE safety beam has been tripped and the

preset time has elapsed. This function is only available

with the addition of a functioning photo-electric safety

beam (Factory Default = Off).

Auto-Close Mode allows you to set a timer from 5–400

seconds before the gate begins to close. In this mode the

gate will close if the photo beam is not triggered after the

time has elapsed.

Important: If the photo beam is tripped within the time

limit the gate will close 5 secs after the beam is restored.

PE Close Mode allows the gate to close 5 secs after the

photo beam has been tripped.

Important: The gate will remain open until the beam is

tripped.

1. Make sure that a functioning PE beam is connected

and Photo Beam Mode is set to On as per Page 14.

2. Press MENU for 3 secs then SET to cycle though to

Auto-Close or PE Close.

3. Press MENU to choose On.

4. Press SET to conrm or MODE to save and exit.

Setting Auto-Close Timer

Delay

Auto-Close Time delay is used with Auto-Close Mode to

allow the gate to close automatically after the timer has

elapsed.

Note: Auto-Close Mode must be enabled to use this

function.

1. Press MENU for 3 secs then SET to cycle though to

Auto-Close Delay.

2. Press and hold MENU to increase or PB to decrease

delay time in 5 sec increments (Max. 400 secs).

3. Press SET to conrm or MODE to save and exit.

Setting Pedestrian Auto-

Close and Timer Delay

If Pedestrian Mode is activated the above functions are

also available for Pedestrian Mode. Follow the above

procedure to enable auto-close and set a time delay as

required.

Hands Free Learning

Hands Free Learning allows the coding of new transmitters

via an existing already coded one instead of pressing the

CODE button. This function is useful if multiple remotes

are to be coded for one site.

(Factory Default = On).

1. To disable this function press MENU for 3 secs then

SET to cycle though to HF Learning.

2. Press MENU to choose Off (Fig. 34).

3. Press SET to conrm or MODE to save and exit.

Auto Close

060 secs

PE Close

Auto Close

030 secs

HF Learn

Fig. 30

Fig. 32

Fig. 31

Fig. 33

Fig. 34

-16-

Power Save Mode

Power save mode allows the opener to go into a sleep

state when not in use. Not only does this save power but

it also greatly increases the life of back up batteries.

Note: When using auxiliary devices such as a photo

electric beam or external third party receiver and

transmitters power save must be disabled (off)

otherwise they will not receive power once the gate

has closed. (Factory Default = On).

1. Press MENU for 3 secs then SET to cycle though to

Power Save.

2. Press MENU to choose Off.

3. Press SET to conrm or MODE to save and exit.

Manual Disengagement

The Smart Slider opener is equipped with a manual

disengagement device to enable you to open and close

the gate in case of electrical failure, system malfunction

or re.

1. For Manual Operation

Use the key to unlock the manual release latch. Pull

the latch out to a 90° angle. If the latch feels hard

to move you may need to use your spare hand to

move the gate slightly to free the gearbox. Do not

use excessive force. If excessive force is used it may

result in damage to the disengagement mechanism.

Before disengaging the gate to manual operation

make sure power is off.

2. To Re-engage the Gate

Your Smart Slider is equipped with an automatic

re-engagement mechanism. Close the latch and lock

it into place the opener gearbox automatically re-

engages. The opener will automatically recognise the

gates position between the travel limits on the next

operation.

Important Information for

the User

Once the Smart Slider opener has been installed, the

user must be informed about how it works and all the

risks that can arise if it is used improperly. The user must

avoid placing him/herself in dangerous situations such as

standing within the gateway when it is moving.

Do not let children play near the gate and keep the

remote controls out of their reach.

All servicing, repairs or checks must be carried out

by professionally qualied personnel and noted on a

maintenance register kept by the user.

Information for the user is found in the USERS/OWNERS

MANUAL included with this opener.

IMPORTANT: Please make sure the USERS/OWNERS

MANUAL is passed on to the owner prior to leaving the

installation.

IMPORTANT: In case of a malfunction the user must call

an authorised Smart Openers Pty Ltd service technician

and should not attempt to repair the fault themselves.

smart

slider

smart

slider

smart

slider

smart

slider

smart

slider

smart

slider

smart

slider

smart

slider

Fig. 36

Fig. 37

Power Save

Fig. 35

Maintenance

No particular maintenance is required for the logic circuit

board.

At least twice a year check that the gate is properly

balanced, travelling smoothly and that all working parts

are in good working condition.

IMPORTANT: A poorly operating gate can effect the life of

the automatic opener due to incorrect loads and will void

the warranty.

Check the reversing sensitivity at least twice a year and

adjust if necessary.

Make sure that the safety devices are working effectively

(photo beams, etc.)

Final Notes

This manual is only for use by technical personnel

qualied to carry out the installation.

No information given in this manual can be considered of

any interest to the end user.

No setting or adjustments contained in this manual

should be carried out by the end user.

It is important for the installer to show their clients correct

operational use of the Smart Slider including the use of

the manual disengagement lever.

Inform the owner about the need for regular and accurate

maintenance, especially regarding a regular check of the

safety and reversing devices.

Technical Specications

Power Input: 240 VAC ±10% 50Hz

Motor: 24V DC

Working Temperature: -10° ~ 60°C

Relative Humidity: <90%

Open and close force: 300N

Receiver frequency: 433.22MHz

Code Capacity: 200 Transmitters

Sensitivity: >1V for correct receiver signal

(average range 50m, with an

aerial)

Decoding: Rolling code

Transmitter power: 27A 12V Battery

NOTE: Smart Openers Pty Ltd reserves the right to

modify its product and product specications at any

time without prior notice.

-17-

-18-

Warranty and Exclusion of Liability

1. This warranty is an addition to any conditions or warranties that are implied by relevant statute, including the Trade Practices Act 1974 (Cth),

which cannot be excluded or negated.

2. Subject to all of the matters set out below, Smart Openers Pty Ltd (“Smart Openers “) warrants:

(a) swing and sliding gate opener drive units for twelve (12) months

(b) roll-up and overhead door opener drive units for twenty four (24) months

from the date of purchase (specied in the sales docket receipt) as free of any defects in material and workmanship.

3. This warranty applies only where the purchaser:

(a) immediately noties Smart Openers or the retailer of the alleged defect;

(b) returns the product to Smart Openers or the retailer; and

(c) presents the relevant sales docket and this warranty document to the retailer and, if so requires, to Smart Openers to conrm the

date of purchase.

4. Defects or damage partly or wholly due to any of the following causes are not covered by this warranty:

(a) accidental damage to any of the Product or to the Product’s components;

(b) normal wear and tear to the Product or to the Product’s components;

(d) incorrect, improper, inappropriate or unreasonable maintenance and/or use;

(e) installation, adjustment or use which is not in accordance with the instructions set out in installation instructions incorporated in the

document;

(f) attempted or complete modication or repairs to the Product or tampering with the Product carried out by a person who is not

authorised by Smart Openers to carry out such modication or repairs;

(g) faulty or unsuitable wiring of structure to which the Product is xed or connected;

(h) radio (including citizen band transmission) or any electronic interference;

(i) blown fuses or damage caused by electrical surges, power surges or power spikes;

(j) damage caused by insects or any infestation;

(k) negligence or deliberate damage.

5. Except for this warranty, Smart Openers gives no warranties of any kind whatsoever (whether express or implied), in relation to the product,

and all warranties of whatsoever kind relating to the product are, to the extent permissible by statute, hereby excluded and negated.

6. To the extent permissible by statute, Smart Openers disclaims any liability of whatsoever nature in respect of any claim or demand for loss or

damage which arises out of:

(a) accidental or deliberate damage to, or normal wear and tear to, the product or to the product’s components;

(b) any cost relating to damage resulting from wear and tear;

(d) loss or damage due to theft, re, ood, rain, water, lightning, storms, any acts of God, contamination or pollution;

(e) door or gate not in safe and correct working order and condition;

(f) evidence of unauthorised repairs;

(g) any cost relating to damage caused deliberately or by misuse, negligence or failure to maintain the equipment in a proper working

order, including (without limitation) due to anything described in paragraphs (d) and (e);

(h) installation, adjustment or use which is not in accordance with the instructions set out in installation instruction manual and owners

manual;

(i) attempted or complete modication or repairs to the Product or tampering with the Product carried out by a person who is not

authorised or has not been trained by Smart Openers to carry out such modication or repairs;

(j) faulty or unsuitable wiring of structure to which the Product is xed or connected;

(k) radio (including citizen band transmission) or any electrical interference;

(l) damage caused by insects or any infestation;

(m) loss or damage to any property whatsoever or any loss, damage or expense whatsoever resulting or arising therefrom;

(n) any consequential, indirect, special or incidental loss or damage;

(o) any cost or expense arising due to manufacturer recall of any product;

(p) any cost or expense due to negligence of the approved service provider;

(q) installation of a residential garage door or gate opener in a commercial or industrial situation or a non-single residential dwelling.

7. Smart Openers liability under this warranty is limited, at Smart Openers absolute option, to replacing or repairing the product which Smart

Openers, in its unfettered and absolute opinion, considers to be defective either in material and/or workmanship or to credit the dealer with

the price at which the product was purchased by the dealer.

8. This warranty does not extend to cover labour for installation.

9. This warranty is limited to Return-to-Base (RTB) repair and does not cover labour for on-site attendance.

10. This warranty is void if the Product is not returned to the manufacturer in original or suitably secure packaging.

11. This warranty is only applicable for repairs to the Product carried out within Australia and for Product in Australia.

12. This warranty does not cover consumable items including globes, batteries and fuses.

13. This warranty is not transferable.

14. Where the Product is retailed by any person other than Smart Openers , except for the warranty set out above, such person has no authority

from Smart Openers to given any warranty or guarantee on Smart Openers behalf in addition to the warranty set out above.

Notes:

1. This warranty is to be read in conjunction with the installation manual and owner’s manual.

-19-

Notes

product quality and innovation Smart Openers reserves the right to change and alter specications and model numbers and types without notice.

No part of this publication may be reproduced, utilised, transmitted, or distributed in any form by any means including photocopying, recording, mechanical,

electronic or otherwise by any party, without the written permission from the publisher Smart Openers Pty Ltd. Copying without authorisation is ILLEGAL.

D/N: SLIM050613

Smart Openers Pty Ltd

PO Box 6666 GCMC, Qld 9726

Tel: 1300 366 547 Fax: 1300 366 972

Email: [email protected]

Web: www.smartopeners.com