SMART 3424WRM6 User manual

SENTINELLA SOLAR PIR SENSOR LIGHTS
Instruction Manual Model 3424WRM6
6. TECHNICAL DATA
7. SPARE PARTS
Battery model: BT-AA-1.2-1200
Battery description: 1.2V Ni-Mh AA Battery 1200mAh
8. FULL 1 YEAR WARRANTY
If within 12 months from the date of purchase this product
fails due to a defect in material or workmanship, Smart Solar
will replace or repair it free of charge.
The warranty does not apply to:
Damage caused by accidents, abuse, poor handling, frost or
normal wear and tear. Products which have been subject to
unauthorized repair or modification or the batteries used
in this product. For further information, please contact
your nearest service centre detailed on the last page of this
instruction manual.
LED description Super bright white LEDs (5 per light)
LED brightness 1200mcd
LED consumption 300mA for the entire circuit (10mA x 30)
LED voltage 3.2V
solar panel (Voc) 6V
solar panel (Isc) 150 mA
Battery size
and type
AA - Ni-Mh
Battery capacity 1.2V - 1200MaH (3pcs)
Model 3424WRM6
Sentinella Solar PIR
Sensor Light Set
6 motion-activated bollard lights
Decorative lighting for illuminating pathways
For further
information,
including parts,
warranty repair
or general inquiries,
please contact
Smart Solar at:
USA Corporate Office
Tel:
1-813-343-5775
Website:
www.smartsolar.com
For ease of locating
parts and to make
customer service
inquiries more
efficient kindly
register your
purchase at www.
smartsolar.com/
registration or simply
hit the “Product
Registration” button
found in the
customer service
section of our
website.
Made In China

SENTINELLA SOLAR PIR SENSOR LIGHTS
Instruction Manual Model 3424WRM6
SENTINELLA SOLAR PIR SENSOR LIGHTS
Instruction Manual Model 3424WRM6
4. ASSEMBLING AND USING YOUR PROUCT
First, find a location where you want to have motion
activated illumination. Put the first stake in the ground and
connect with the waterproof plug to the solar power station.
Install in a series the remaining 5 bollard lights using the
stakes provided. Carefully position the first and last bollard
light (each of these bollard lights has a small white PIR sensor
about 3/4 of the way up) in such a manner to capture motion
from the direction desired. Once all lights are installed,
simply press the switch button on the back of the solar power
station to have the circuit activated. To verify that you have
the circuit connected, simply cover the solar panel and then
pass by the motion sensor and the lights will illuminate.
5. REMOVING/REPLACING THE BATTERIES
There are 3pcs of AA 1200MAH NI-MH rechargeable batteries
inside the back of the solar power station. The normal life of
batteries is about one-two years depending on conditions. The
batteries will need to be replaced when the light becomes weak
within 3 hours of lighting after fully changed, or the batteries
have been used for more than one year and operation is poor.
The methods of changing battery are as follows:
1. Carefully remove the solar panel unit from the stand. Using a
screwdriver, carefully remove the four screws at the back of the
unit. Remove the back cover and you will see three batteries
2. Remove the three used batteries and replace with new ones
3. Re-tighten the screws
4. A new battery is fitted in reverse order
PLEASE NOTE: Used batteries must be disposed of carefully
with regard to the environment and should NOT be put into
the family waste. Consult your local waste authority for
specific requirements.
ATTENTION: Please position the solar panel directly at the
sunlight by adjusting the solar panel unit. During winter
(snow) months we recommend that the snow be removed
from the solar panel to protect the solar panel and maximize
the efficiency of the circuit.
FULLY ADJUSTABLE
SOLAR UNIT
135
mm 100mm
nut
transparent cover
solar panel unit
pole
125mm
stake
145mm
PIR
45mm 42mm
PIR
270mm
aluminum
tube
stake
100mm
50mm
1. INTRODUCTION
Thank you for purchasing the Sentinella Solar PIR Sensor
Lights. You have purchased a product that complies with
the latest and most up-to-date solar technology available.
To maintain safety and correctly, you should adhere to the
instructions for use detailed in this manual.
2. COMPONENTS
Note: all dimensions are in millimeters (mm)
3. OVERVIEW
The solar PIR sensor light has been designed for outdoor
use. The solar panel in the upper part of the solar power
station converts sunlight into electricity which is then stored
in the rechargeable batteries. The light is controlled by a PIR
(passive infra-red) sensor to automatically detect movement
and illuminate during night time. The sensor will trigger the
circuit and illuminate all 6 lights for 30 seconds and then they
will turn off. The circuit can illuminate approximately 300
times when the battery is fully charged. The source of light
comes from thirty (30) super bright white patented LEDs (5
per Bollard Light), which provide very high brightness but
benefit from very low power consumption. For maximum
performance, the solar panel must to be placed in direct
sunlight.
REMOVE SCREWS ON
BACK OF SOLAR
PANEL TO REPLACE
THE BATTERIES
SWITCH
SCREWS
BATTERIES
SENTINELLA LIGHT
SOLAR UNIT
50mm