SmartDHOME MyVirtuoso Home Zone Thermostat User manual

Zone thermostat for 2-pipe fancoil with 0-10 Vdc fan regulation and
valve management
User manual
1
Thank you for choosing the zone thermostat for 2-pipe fan coils with 0-10 Vdc fan regulation
and valve management. Z-Wave certified, the device is compatible with the gateways of the
MyVirtuoso Home home automation system.
www.myvirtuosohome.com
www.smartdhome.com

Zone thermostat for 2-pipe fancoil with 0-10 Vdc fan regulation and
valve management
User manual
2
Description and Technical features
The zone thermostat for fan coils is a Z-Wave device for controlling the internal temperature.
This device is designed to be applied to a 2-pipe fan coil system. It can detect the ambient
temperature, the local time and automatically controls the fan speed based on the
temperature difference. This product can be included and used in any Z-Wave network with
other Z-Wave certified devices.
Features
•Power supply: 230V, 50 / 60HZ
•Resistive load: ≤ 3A
•Self-consumption: <1W
•Fan regulation: 0-10 Vdc
•Temperature sensor: NTC 10K
•Display accuracy: 0.1 ° C
•Work environment: 0 ～ 55 °C; <95% RH (not condensed)
•Temperature setting: 5 ～ 35 °C (adjustable)
•Dimension: 86 * 86 * 42mm
•Electrical box compatibility: 86 * 86
•Z-Wave frequency: 868.42 MHz (EU)
Package content
•Zone thermostat for fan coils
•Use manual
Installation
To install the device correctly, follow the instructions below:

Zone thermostat for 2-pipe fancoil with 0-10 Vdc fan regulation and
valve management
User manual
3
1. Remove the steel frame from the device and fix it to the junction box with two screws.
2. Insert all wires into the appropriate terminals and tighten the screws. The wiring
diagram is shown below.
3. Attach the wired device to points "A" of the steel frame as shown in the image, then
push it into the junction box.
4. Check if the device is secure and switch on.
Wiring Diagram
Buttons and Display
1. Temperature settings
2. Room temperature
3. Heating
4. Valve
1
2
3
4
Auto
Lento
Medio
Veloce

Zone thermostat for 2-pipe fancoil with 0-10 Vdc fan regulation and
valve management
User manual
4
Operations
ON/OFF
To turn the device on and off, simply press the ON / OFF button .
Local time setting
Press and hold the M button to access the settings menu. Select the local time and press M
to move from Week to Hour to Minute, then press or to set the parameters of the
flashing item. Press M or wait 15 seconds to save the settings.
Temperature setting
Touch or to set the local temperature value. Press and hold the buttons can be set
continuously. Press M or wait 15 seconds to save and return to room temperature.
Mode settings
Tap M to enter working mode setting, the current mode flashes. Press or to switch
between Cooling , Heating and Ventilation modes , then press M or wait 15
seconds to confirm your choice.
Ventilation mode settings
In normal view, press to switch between fan speeds: “Low, Medium, High, Auto”. Then
press M, or wait 15s to confirm the choice.
•Manual fan control
If you decide to manually set the fan speed, the device:
•Heating mode
1. It will close the valve and stop the ventilation if the room temperature is
≥ the set one.
2. It will open the valve and turn on the ventilation if the ambient
temperature is ≤ the set one - 1 ° C.
•Automatic fan control
Heating
Mode
1. Room temperature ≥ set temperature, the fan stops
2. Room temperature ≤ set temperature -1 ° C, the fan turns on in
slow speed.
3. Room temperature ≤ set temperature -2 ° C, the fan turns on in
medium speed.

Zone thermostat for 2-pipe fancoil with 0-10 Vdc fan regulation and
valve management
User manual
5
4. Room temperature ≤ set temperature -3 ° C, the fan turns on in
fast speed.
Note: the thermostat will operate on, off and speed of the fans only if they are open.
Inclusion
Before starting the procedure for including the device in a Z-Wave network, check that it is
turned on, then make sure that the MyVirtuoso Home gateway is in inclusion mode (refer to
the relevant manual available on the website www.myvirtuosohome.com/downloads).
1. After turning off the device, press and hold to access the inclusion interface. The
display will show “- - - “.
2. Press once and the device will enter into ID search mode. The inclusion will be
successful if the ID is displayed on the screen.
Note: after inclusion, the device must be turned off and on again.
Exclusion
Before starting the procedure for excluding the device in a Z-Wave network, check that it is
turned on, then make sure that the MyVirtuoso Home gateway is in exclusion mode (refer
to the relevant manual available on the website www.myvirtuosohome.com/downloads).
1. After turning off the device, press and hold to access the inclusion interface. The
display will show “- - - “.
2. Press once and the device will enter into ID search mode. The exclusion will be
successful if the ID is displayed on the screen.

Zone thermostat for 2-pipe fancoil with 0-10 Vdc fan regulation and
valve management
User manual
6
Disposal
Do not dispose of electrical appliances in mixed urban waste, use separate collection
services. Contact the local council for information about available collection systems. If
electrical appliances are disposed of in landfills or in inappropriate places, hazardous
substances can escape into groundwater and enter the food chain, damaging health and
well-being. When replacing old appliances with new ones, the retailer is legally obliged to
accept the old appliance for free disposal.
Warranty and customer support
Visit our website: http://www.ecodhome.com/acquista/garanzia-eriparazioni.html
If you encounter technical problems or malfunctions, visit the site:
http://helpdesk.smartdhome.com/users/register.aspx
After a short registration you can open a ticket online, also attaching images. One of our
technicians will answer you as soon as possible.
SmartDHOME Srl
V.le Longarone 35, 20058 Zibido San Giacomo (MI)
[email protected]
Product Code: 01335-1864-00
Rev. 01/2022