Smarte S4K-8x8 User manual

S4K-8x8
Instruction Manual
MODEL : S4K-8x8
8x8 HDMI-HDBaseT Matrix Switch with Auxiliary Audio
I/O with PoH (Power Over HDBaseT)

SAFETY INFORMATION
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL
1. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit, use only the original
factory packing.
2. Read all documentation before operating your equipment. Retain all documentation for future reference.
3. Follow all instructions printed on unit chassis for proper operation.
4. Do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
5. Make sure power outlets conform to the power requirements listed on the back of the unit.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not likely to be walked on
or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit
7. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the means of grounding of
a piece of equipment is not defeated.
8. Mains voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC voltage is not covered by
any warranty.
9.
Power down & disconnect unit from mains voltage before making connections.
10. Never hold a power switch in the ＂ON＂ position.
11. Do not use the unit near stoves, heat registers, radiators, or other heat Producing devices.
12. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal flow of air around the unit,
13.
such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky environment, the unit should be
Periodically ＂blown free＂ of foreign matter.
14.
Do not remove the cover. Removing the cover will expose you to potentially dangerous voltages. There are no user serviceable parts inside.
15.
Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
16.
Non-use periods. The power cord of equipment should be unplugged from the outlet when left unused for a long period of time.
Service Information Equipment should be serviced by qualifier service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain
D. The equipment does not appear to operate normally, or exhibits a marked change in performance
E. The equipment has been dropped, or the enclosure damaged.
from the appliance.
IMPORTANT SAFETY INSTRUCTIONS
To insure the best from this product, please read this manual carefully. Keep it in a safe place for future reference.
To reduce the risk of electric shock, do not remove the cover from the unit. No user serviceable parts inside. Refer servicing to qualified personnel.
To reduce the risk of fire, do not expose the unit to rain, water or excessive moisture.
Do not force switched or external connections.
When moving the unit disconnect the serial port connections first then the power cable and finally the interconnecting cables to other devices.
Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Use a clean dry cloth.
Installation of this unit should be in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold.
This symbol is intended to alert the user to the presence of uninsulated
enclosure tha may be of sufficientmagnitude to constitue a risk of
electric shock to persons.
This symbol is intended to alert the user to the presence of important
operational and maintenance (serving) instructions in the literature
accompanying the appliance.
T prevent electric shock do not use this (polarised) plug with an o
extension cord, receptacle or other outlet unless the blades can
be fully inserted to prevent blade exposure.
T prevent electric shock, match wide blade of plug to wide slot, o
fully insert.
Caution:
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK),
NO USER SERVICEABLE PARTS INSIDE,
REFER SERVICING TO QUALIFIED SERVICE PERSONAL.
WARNING!
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK
T
I
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. .
DO NOT OPEN
of uninsulated “dangerous voltage” within the products enclosure that
RISK OF ELECTRIC SHOCK

PAGE 3
S4K-8x8 INSTRUCTION & OPERATION MANUAL
TABLE OF CONTENTS
TABLE OF CONTENTS
INTRODUCTION AND PACKAGE CONTENTS
FEATURES
SPECIFICATION-1
SPECIFICATION-2
FRONT PANEL & FUNCTION KEY DEFINE :
1 - Front Panel Key Define
2 - ARC
3 - AUX
4 - EDID
5 - ALL, OFF, LOCK & ENTER
6 - RECALL & MEMORY
REAR PANEL I/O DEFINE :
1 - Switch Control
2 - HDMI I/O
3 - HDBaseT Controls
4 - HDBaseT out & HDBaseT I/O Transmission
EDID FUNCTION DEFINE :
EDID-1 - EDID SETUP
EDID-2 - (7) EMBEDDED EDIDs
EDID-3 - LEARNING MODE-#1 SINGLE LEARNING
EDID-4 - LEARNING EDID Signal>Signal, Single>Multiple & Single>ALL
EDID-5 - LEARNING MODE-#2 MULTIPLE LEARNING
EDID-6 - EDID DEFINITIONS
TYPICAL APPLICATIONS :
1 - TYPICAL-#1 Switch controls
2 - TYPICAL-#2 HDBaseT I/O Applications
3 - TYPICAL-#3 HDBaseT IR Matrix Applications
SWITCH CONTROL :
1. IR Remote Controller
IR DATA CODE
ROOM 1~4 IR Remote Controller
ROOM 5~8 IR Remote Controller
2. IR EXTERNAL : Switch IR-in INSTALL
3. ETHERNET INSTALL
4. RS232 Series INSTALL
SYSTEM RESET - Factory Defaults
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
_____________________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________
___________
_______________________________________________
___________________________________________
___________________________________________
___________________________________________
_______________________________________________
_______________________________________________
_______________________________________________
_____________________________________________________
_______________________
_______________________________________________
_______________________________________________
_______________________________________________
_______________________________________________
_______________________________________________
_______________________________________________
_______________
_______________________________________________
_______________________________________________
_______________________________________________
_______________________________________________
______________
_______________________________________________
_______________________________________________
_______________________________________________
_______________________________________________
_______________________________________________
_______________________________________________
______________
_______________________________________________
_______________________________________________
_______________________________________________

INTRODUCTION AND PACKAGE CONTENTS
PAGE 4 S4K-8x8 INSTRUCTION & OPERATION MANUAL
PACKAGE CONTENTS
INTRODUCTION
The S4K-8x8 is professional 8x8 matrix routing switch with PoH. Supporting eight (8) HDMI Inputs and (8) Auxiliary
Audio Inputs. Output supported (8)x HDMI, (8)x SPDIF and 8x HDBASET (PoH). The S4K-8x8 is based on the HDBASET
standard and supports full resolution HDMI Video with embedded EDID and PoH function, Audio, RS-232, Ethernet
and bi-directional IR, all over a single Category cable. With a signal bandwidth of 340Mhz, there is no signal
degradation. High Definition Digital signals can be selected and distributed to any (8)x Inputs to (16)x outputs
simultaneously (channel outputs mirrored). The Switcher is certified as being fully CEC , ARC and HDCP 2.0 compliant,
full HD 4K2K HDMI V1.4a 3D formats, data rates up to 6.75 Gbps. Supports UXGA/WUXGA/DVI 1920x1200 resolution
to any HD displays. The S4K-8x8 has 1x HDMI and Auxiliary Audio (analog stereo audio) connector for Input,
effectively making this an (8) in x (16) out switcher (same signal on both outputs). Using IR remote the switcher’s
HDBASET Extender Transmitter (Tx) allows you to connect a source in a remote location. Likewise, the HDBASET Output
and our HDBASET Receiver allows you to connect a display in a remote location. The EDID management can be
selected between seven (7) different modes. Control is provided via Front panel push buttons, IR remote, RS-232 or
TCP/IP (not a web-browser). An RS232 Windows GUI interface is provided for matrix routing control (Windows only).
1. S4K-8x8 Matrix Switcher
2. Operating Instructions
3. RS-232 V2.0 Protocol Instructions
4. Ethernet V2.0 Protocol Instructions
5. Master wireless IR Remote Control (SW-5688AK)
6. 8 each; Individual wireless IR Control (SW-5688CAK-IR01~IR08)
7. 19 inch Ear mount bracket (Part # 2U-440L)
8. SB-101 IR Extender distance ~984 feet (300M) Transmitter set.
9. SB-100 IR Extender distance ~984 feet (300M) Receiver set.
10. SB-101C IR Extender distance 6ft(2M) Transmitter Cable.
11. SB-100C IR Extender distance 6ft(2M) Receiver Cable.
12. CD Contents : This manual, Windows GUI, ISP V1.0 Windows driver
13. RS232 Cable 6 feet (2M)
14. Worldwide Universal Power Supply Input : 100~240 VAC, AC 50/60Hz.
15. ISO Screws

PAGE 5
S4K-8x8 INSTRUCTION & OPERATION MANUAL
FEATURES
FEATURES
Based on HDBaseT; bi-directional IR, RS-232, Multi format Audio, Ethernet and PoE. Full
resolution HD Video, all HDBaseT signals over one CATx cable.
(8)x HDMI with Auxiliary Audio (Analog Audio) player devices matrix switched to
(8)x HDMI with S/PDIF outputs and (8)x HDB T Transmitter with PoH output to (8)x destinations.
Application HDBaseT Specification with PoH 48VDC, IR, RS-232, Multi Audio Format and HD.
Video Signals over one CATx (6/6a/7) category cable.
HDMI digital Video w/embedded HDCP, DVI format and CEC/HDCP 2.0 compliant
Worldwide control EDID modes for HDMI full 4K2K (24/30 Hz) HD Video resolutions.
Link speeds of up to 6.75 Gbps (link clock rate of 340MbHz), Support HDMI 4K2K, 1.4a 3D formats.
Wide range of HD resolutions from PC XGA to WUXGA 1920x1200 and HDTV/DTV HDMI resolutions
480i/480p, 576i/576p, 720p, 1080i/p & 4K2K (24/30Hz).
Compatible with all HDMI source devices, PC monitors, Plasma HD display, HDTV and audio receivers
or audio amplifiers.
Digital Video TMDS formats Resolution up to 4K2K with Deep color 36-bit.
Digital Audio Support : - Dolby TrueHD,
- Dolby Digital,
- Dolby Digital Plug/ex,
- DTS,
- DTS-HD,
- DTS-HD Master,
- DTS-EX
- PCM, PCM2, LPCM2..
Audio Input : Support Auxiliary Audio (Analog stereo audio).
Audio Output : Support Digital audio ARC or Digital audio S/PDIF ( from HDMI source or Auxiliary Audio )
Various User Interface controls:
‧Windows based GUI control via RS232 port
‧Front Panel push button
‧IR wireless remote controller
‧Ethernet Switch control
‧Third party RS232 controller (via simple ASCII)
Support world wide (9)x control function keys:
Full function front panel controls: ARC / AUX/ ALL / OFF / EDID / LOCK / RECALL / MEMORY / ENTER
Support EDID modes :
a. (7) Embedded EDID modes :
FSS/ H24-3D/ H24-3D-M/ H36-3D/ H36-3D-M/ 4K2K-3D / DVI-D 1920x1200-60Hz
b.External modes : Learning mode-1(Single Learning) & Learning mode-2(Multiple Learning).
Automatic scanning input & output status via LCM show on front panel.
Using the build-in booster, each HDMI Output port is capable of driving cable lengths
1080p up to 98 feet (30M) & 4k2k up to 66 feet (20M) .
Support IR Remote and IR Extender with distance up to ~ 984 feet (300M) Maximum.
Support Universal power adaptor AC100V~AC240V, 50/60Hz.
The Switcher will remember that last state during a power cycle.
When power is removed and resorted, the last configuration will be invoked.
ASE
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.

SPECIFICATIONS
SPECIFICATIONS
As product improvement is continuous, specifications are subject to change and without notice or liability.
PAGE 6 S4K-8x8 INSTRUCTION & OPERATION MANUAL
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
Type of HDMI Switcher
HDMI Support
HDBaseT Support
HDCP / CEC Support
Video Bandwidth
Digital Video Support
Video Inputs
HDMI
Audio Inputs
Audio
Video Outputs
HDMI
HDBaseT
Audio Outputs
S/PDIF
ARC
HDMI
HDBaseT Control In
HDBaseT Control Out
HDBaseT Control I/O
Switch Controls
8x inputs To 8x Outputs Matrix Switch
HDMI 4K2K, 1080P-@60Hz, H36-bit Deep color, 3D of HDMI V1.4 formats.
bi-directional IR, RS-232, Multi format Audio, Ethernet and PoE. over one Category cable.
HDCP 2.0 Compliant, CEC Compliant.
Double Data Rates: 340Mhz, Total 6.75Gbps bandwidth.
HD:480i/ 480p/ 720p/ 1080i/p and 4K2K up to 36bit deep color
8x HDMI (HDMI or DVI digital source).
8x Audio ( Analog Stereo, AUX port. 3.5mm Jack).
8x HDMI : With Booster output 1080p up to ~98feet(35M) & 4K2K up to ~66feet(20M).
8x HDBaseT Transmitter (with PoH 48VDC via category cable & RJ-45 connector)
8x S/PDIF : Multi Audio Formats 5.1 from HDMI or LPCM-2CH from Auxiliary audio.
8x ARC : TV Return Channel Audio.
8x HDMI : Multi Audio Formats 5.1 / 7.1, MAT(MLP),
Dolby Digital, Dolby TrueHD,
Dolby Digital Plus,
DTS, DTS-ES 6CH,
DTS-HD, DTS-HD-HRA,
DTS-HD Master,
(PCM-2CH)
8x IR in (Send IR signals To 8x Rooms via HDBaseT Transmitter)
1x ALL IR in (Send IR Signals To 8x Rooms - Via HDBaseT Transmitter)
8x IR out (Link to Receive IR signals from 8x Rooms via HDBaseT Extender)
1x ALL IR out (Link to Receive IR signals from 8x Rooms via HDBaseT Extender)
1x All Tx LAN (All Switcher HDBaseT Transmitter Ethernets link to HDBaseT Receiver)
8x RS-232 I/O (Control 8x Rooms RS-232 via Switcher HDBaseT Extender Tx)
1x Select & Function buttons on front panel (Data status via LCM panel show out)
1x IR Remote Controller (switch control)
8x IR Room Remote Controller (switch control)
1x IR External port (switch control via 3.5mm OD Jack)
1x RS 232 series interface (switch control)
1x Ethernet series interface (switch control)
HDMI over HDBaseT with Audio and Extension

SPECIFICATIONS
SPECIFICATIONS
Source Status
(25) Function Control Keys
(7) EDID management
Infrared Frequency
IR External Distance
HDBaseT Extender Distance
HDMI I/O Connector
Temperature
Dimensions
Rack Mount
Power Supply
Safety Approvals
Product Weight
Input status LEDs indicates presence of a live signal.
1. ARC
2. AUX
3. ALL
4. OFF
5. RECALL
6. ENTER
7. MEMORY
8. LOCK
9.EDID
10. Destination button 1 thru 8
11. Source button 1 thru 8
Select Embedded EDID modes :
®
Mode1: Fast Speed Start
Mode2: H24-3D
Mode3: H24-3D-M
Mode4: H36-3D
Mode5: H36-3D-M
Mode6: 4K2K-3D, PCM-2CH
Mode7: DVI-D 1920x1200
Select LEARNING mode : Learning Destination EDID To Link Source.
Learning mode-1 (Single Learning), Learning mode-2 (Multiple Learning).
38 Khz
~984 feet / 300 meters maximum.
~328 feet / 100 meters maximum.
HDMI Type A - SMD 19pin Female Type
Operating Temperature 32 °F - 100 °F (0 °C - 32 °C)
LxWxH=19 ”x 9.85 ”x 3.46 ”(482mm x 250mm x 88mm)
2RU High 19 ”Rack Mount #2U-440L (with rack mount)
AC 100~240 VAC 50/60Hz (Power Consumption:10A Maximum)
CE, FCC, RoHS, REACH, WEEE.
3.85 Kgs / 8.47 lb
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
As product improvement is continuous, specifications are subject to change and without notice or liability.
PAGE 7
S4K-8x8 INSTRUCTION & OPERATION MANUAL

Before making any connections to the switcher. Observe the following:
> Ensure the mains voltage supply matches the label on the supplied plug-
Pack (+/- 10%)
> Ensure that the power switch is OFF
> Ensure that all system grounds (earth) are connected to a common point.
> Avoid powering equipment within a system from multiple power sources
that may be separated by large distances
REMOTE CONTROL
REMOTE CONTROL
> Connect all audio video sources and destination equipment
> power up all source and destination audio-visual sources
> For each destination output select the appropriate input source by using
> Upon power up the switcher will return to its last used setting before
The front panel input 1~8 select buttons. The supplied IR remote control.
Or through the RS 232 serial communications port.
Powered down.
PAGE 8 S4K-8x8 INSTRUCTION & OPERATION MANUAL
SWITCH POWER ON or OFF
1
Controller with a separate power ON and OFF
DESTINATION : 1 thru 8 OUTPUT SELECTION
Press the destination button to select the output
display channel.
2
3
FUNCTION KEY
ARC
AUX
ALL
OFF
EDID
RECALL
MEMORY
ENTER
LOCK
5
SOURCE : 1 thru 8 INPUT SOURCE SELECTION
Press input 1~8 sources with selection button
4
3
4
5
2
1
IR REMOTE
IR REMOTE CONTROL KEY :
- function selection button
- function selection button
- function selection button
- function selection button
- function selection button
- function selection button
- function selection button
- function selection button
- function selection button
5 6 7 8
A15E A25D
10EF 20DF 30CF 40BF
50AF 609A 708F 807F
06F9
07F8
B04F
B34C
B44B
02FD01FE 03FC
05FA 08F7
B14E
B24DB54A
04FB
B748
POWER
1 2 3 4
ON OFF
MEMORY
DESTINATION
SOURCES
RECALL
1 2 3 4
5 6 7 8
ENTER
LOCK
EDID
ALL OFF
ARC AUX
9966
B847

IR REMOTE CUSTOM AND DATA CODES (NEC Standard)
REMOTE CONTROL DATA CODES LIST
HOW TO SETUP IR CODES :
POWER ON : A15E
POWER OFF : 46B9 A25D
46B9
CUSTOM CODE : 46B9
PAGE 9
S4K-8x8 INSTRUCTION & OPERATION MANUAL
PRESS DESTINATION then PRESS SOURCE - #- #
DESTINATION #1 :
DESTINATION #2 :
DESTINATION #3 :
DESTINATION #4 :
DESTINATION #5 :
DESTINATION #6 :
DESTINATION #7 :
DESTINATION #8 :
SOURCE #1 :
SOURCE #2 :
SOURCE #3 :
SOURCE #4 :
SOURCE #5 :
SOURCE #6 :
SOURCE #7 :
SOURCE #8 :
01FE
02FD
03FC
04FB
05FA
06F9
07F8
08F7
46B9
46B9
46B9
46B9
46B9
46B9
46B9
46B9
10EF
20DF
30CF
40BF
50AF
609F
708F
807F
For example;
Select Destination # 1 to show Source #1~8,
The IR Data Code list :
Destination # 1 , Source #1
Destination # 1 , Source #2
Destination # 1 , Source #3
Destination # 1 , Source #4
Destination # 1 , Source #5
Destination # 1 , Source #6
Destination # 1 , Source #7
Destination # 1 , Source #8
46B9
46B9
46B9
46B9
46B9
46B9
46B9
46B9
10EF
10EF
10EF
10EF
10EF
10EF
10EF
10EF
46B9
46B9
46B9
46B9
46B9
46B9
46B9
46B9
01FE
02FD
03FC
04FB
05FA
06F9
07F8
08F7
ARC
AUX
ALL
OFF
EDID
LOCK
RECALL
MEMORY
ENTER
:
:
:
:
:
:
:
:
:
46B9
46B9
46B9
46B9
46B9
46B9
46B9
46B9
46B9
B847
9966
B04F
B14E
B748
B54A
B24D
B44B
B34C
FUNCTION KEY CODE LIST:
46B9
46B9
46B9
46B9
46B9
46B9
46B9
46B9

ROOM 1 ~4 REMOTE CONTROL
PAGE 10 S4K-8x8 INSTRUCTION & OPERATION MANUAL
ROOM REMOTE CONTROL #1 ~ #8 CUSTOM CODE AND DATA CODES
IR-01 DATA CODE:
CUSTOM CODE : 46B9
PRESS Number To Select SOURCE
SOURCE #1 :
SOURCE #2 :
SOURCE #3 :
SOURCE #4 :
SOURCE #5 :
SOURCE #6 :
SOURCE #7 :
SOURCE #8 :
11EE
12ED
13EC
14EB
15EA
16E9
17E8
18E7
46B9
46B9
46B9
46B9
46B9
46B9
46B9
46B9
IR CUSTOM AND DATA CODES (NEC Standard)
IR-02 DATA CODE:
SOURCE #1 :
SOURCE #2 :
SOURCE #3 :
SOURCE #4 :
SOURCE #5 :
SOURCE #6 :
SOURCE #7 :
SOURCE #8 :
21DE
22DD
23DC
24DB
25DA
26D9
27D8
28D7
46B9
46B9
46B9
46B9
46B9
46B9
46B9
46B9
IR-03 DATA CODE:
SOURCE #1 :
SOURCE #2 :
SOURCE #3 :
SOURCE #4 :
SOURCE #5 :
SOURCE #6 :
SOURCE #7 :
SOURCE #8 :
31CE
32CD
33CC
34CB
35CA
36C9
37C8
38C7
46B9
46B9
46B9
46B9
46B9
46B9
46B9
46B9
IR-04 DATA CODE:
SOURCE #1 :
SOURCE #2 :
SOURCE #3 :
SOURCE #4 :
SOURCE #5 :
SOURCE #6 :
SOURCE #7 :
SOURCE #8 :
41BE
42BD
43BC
44BB
45BA
46B9
47B8
48B7
46B9
46B9
46B9
46B9
46B9
46B9
46B9
46B9
1
SOURCE
4
11EE 15EA
12ED 16E9
13EC 17E8
14EB 18E7
2
3
5
6
7
8
1
1
SOURCE
4
21DE 25DA
22DD 26D9
23DC 27D8
24DB 28D7
2
3
5
6
7
8
2
1
SOURCE
4
31CF 35CA
32CD 36C9
33CC 37C8
34CB 38C7
2
3
5
6
7
8
3
1
SOURCE
4
41BE 45BA
42BD 46B9
43BC 47B8
44BB 48B7
2
3
5
6
7
8
4

ROOM 5~8 REMOTE CONTROL
PAGE 11
S4K-8x8 INSTRUCTION & OPERATION MANUAL
ROOM REMOTE CONTROL #1 ~ #8 CUSTOM CODE AND DATA CODES
PRESS Number To Select SOURCE
IR CUSTOM AND DATA CODES (NEC Standard)
IR-05 DATA CODE:
SOURCE #1 :
SOURCE #2 :
SOURCE #3 :
SOURCE #4 :
SOURCE #5 :
SOURCE #6 :
SOURCE #7 :
SOURCE #8 :
51AE
52AD
53AC
54AB
55AA
56A9
57A8
58A7
46B9
46B9
46B9
46B9
46B9
46B9
46B9
46B9
IR-06 DATA CODE:
SOURCE #1 :
SOURCE #2 :
SOURCE #3 :
SOURCE #4 :
SOURCE #5 :
SOURCE #6 :
SOURCE #7 :
SOURCE #8 :
619E
629D
639C
649B
659A
6699
6798
6897
46B9
46B9
46B9
46B9
46B9
46B9
46B9
46B9
IR-07 DATA CODE:
SOURCE #1 :
SOURCE #2 :
SOURCE #3 :
SOURCE #4 :
SOURCE #5 :
SOURCE #6 :
SOURCE #7 :
SOURCE #8 :
718E
728D
738C
748B
758A
7689
7788
7887
46B9
46B9
46B9
46B9
46B9
46B9
46B9
46B9
IR-08 DATA CODE:
SOURCE #1 :
SOURCE #2 :
SOURCE #3 :
SOURCE #4 :
SOURCE #5 :
SOURCE #6 :
SOURCE #7 :
SOURCE #8 :
817E
827D
837C
847B
857A
8679
8778
8877
46B9
46B9
46B9
46B9
46B9
46B9
46B9
46B9
1
SOURCE
4
51AF 55AA
52AD 56A9
53AC 57A8
54AB 58A7
2
3
5
6
7
8
5
1
SOURCE
4
619E 659A
629D 6699
639C 6798
649B 6897
2
3
5
6
7
8
6
1
SOURCE
4
718E 758A
728D 7689
738C 7788
748B 7887
2
3
5
6
7
8
7
1
SOURCE
4
817E 857A
827D 8679
837C 8778
847B 8877
2
3
5
6
7
8
8
CUSTOM CODE : 46B9

PAGE 12 S4K-8x8 INSTRUCTION & OPERATION MANUAL
Control Switch S4K-8x8
IR PN#: SW-5688AK
IR PN#: SW-5688AK
Control Switch S4K-8x8
REAR PANEL IR EXTENDER PORT
SB-100 DISTANCE maximum ~ 984 feet (300 meters)
When you plug the External IR extender into the switcher, the front panel IR receiver remains active. Note:
IR EXTENDER PACKAGE :
HOW TO SETUP THE IR EXTENDER RECEIVER COMPONENTS
POWER
INPUT -1
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
HDMI MATRIX SWITCHER
ON OFF
INPUT -2
INPUT -3
INPUT -4
SW IR
Pin configuration for IR 984 feet (300 meters) Extender Receiver such as SB-100 compatible
VCC (Ring)
Signal (center)
GND (Sleeve)
Tip Ring
Sleeve
Tip: Signal
Ring :VCC
Sleeve: GND
Ring
Tip (center)
Sleeve
SB-100 IR Receiver set
IR Extender 300M Receiver
INPUT
DC 12V
Ro HS/ 95/ EC
IR EXT.
RS-232
Switcher IR EXT. In
IR Receiver (SB-100)
Cable(3C)
RS-232 IR EXT. in
SB-100 IR Receiver pack
1. SB-100 IR 300M Receiver
SB-100
IR Rx
Distance:Max.300M
SB-100C DISTANCE 6 feet (2 meters)
SB-100C Receiver Cable
IR cable 6ft (2M)Receiver
2. SB-100C IR 2M Receiver
INPUT
DC 12V
Ro HS/ 95/ EC
IR EXT.
RS-232
Switcher IR EXT. In
IR Receiver (SB-100C)
Cable(2C)
RS-232 IR EXT. in
SB-100C
IR Rx
Distance: Max.(2M)
POWER
INPUT -1
1 2 3 4
1 2 3 4
1 2 3 4
1 2 3 4
HDMI MATRIX SWITCHER
ON OFF
INPUT -2
INPUT -3
INPUT -4
SW IR
SB-100C Receiver Cable
IR cable 6 feet (2M)Receiver
Pin configuration for IR Receiver 6 feet (2 meters) cable such as SB-100C compatible
Signal (center)
GND (Sleeve)
Tip Ring
Sleeve
Tip: Signal
Ring: NC
Sleeve: GND
Ring
Tip (center)
Sleeve
SB-100 Receiver and SB-101 Transmitter The DISTANCE maximum ~ 984 feet (300 meters)
SB-100C Receiver Cable and SB-101C Transmitter Cable The DISTANCE maximum 6 feet (2 meters)
Note:
The External IR jack has voltage on the “Ring” portion of a 3-conductor plug. You must use a 3-conductor plug (aka: stereo plug).
Using a 2-conductor plug will short out the power supply. Always make connections with the switcher power off.
※ The SB-100 IR Receiver is required when using the port “ALL in” Jack.
※ The SB-100C IR Receiver will not function on the port “ALL in” Jack.
SWITCH IR EXTENDER

PAGE 13
S4K-8x8 INSTRUCTION & OPERATION MANUAL
ETHERNET SERIAL INTERFACE
ETHERNET SERIAL INTERFACE CONNECT a PC or CONTROL SYSTEM. VERSION COMPATIBLE V2.0
1 2 3 4 5 6 7 8
ETHERNET SERIAL INTERFACE
Pin
2
3
4
5
6
7
8
For a complete list of commands, please reference external document extended Ethernet Protocol Instruction Manual.
ETHERNET TCP/IP PROTOCOL COMMANDS ( Ethernet / RS232 Control driver V2.0 )
Note :
Control the switcher
SPD : Speed
LINK : Ethernet link
RJ-45 Female 8P-8Cconnector
Ethernet
SPD LINK
Ethernet
TXON
RXIP
NC
NC
RXIN
NC
GND
TXOP
1
Reference
TX +
TX -
RX +
RX -
*** The Ethernet port and RS-232 port cannot be used simultaneously.
Any connection to the Ethernet Control port will disable serial commands send to the RS-232 port.***
Example of the commanded string to route Input 3 to Output 4
OUTPUT04 03;

PAGE 14 S4K-8x8 INSTRUCTION & OPERATION MANUAL
RS-232 SERIAL INTERFACE
RS-232 SERIAL INTERFACE CONNECT a PC or CONTROL SYSTEM. VERSION COMPATIBLE V2.0
1
RS-232 Configuration
For a complete list of commands, please reference external document extended RS-232 Protocol Instruction Manual.
2 3 4 5
6 7 8 9
RS-232 SERIAL INTERFACE PROTOCOL COMMANDS ( Ethernet / RS232 Control driver V2.0 )
The serial communication parameters are 9600 baud, 8 bit, No Parity and 1 stop bit - this is often referred to as 9600 8N1.
When the unit recognises a complete command it will perform the requested action - there is no delimiter character required.
The Smart-e switcher can be controlled via the RS-232 serial control port to allow for interfacing to a PC,
or similar third party control system.
RS-232 cable is a straight thru cable and not null-modem
PIN
1
2
3
4
5
6
7
8
9
PIN
1
2
3
4
5
6
7
8
9
Definition
DCD
RX
TX
DTR
GND
DSR
RTS
CTS
RI
Definition
TX
RX
GND
____________________
____________________
____________________
PC
Device
RS-232 Pin Diagram
Example of the commanded string to route Input 3 to Output 4
OUTPUT04 03;

SYSTEM RESET function For Matrix Switch System Return to Factory Defaults
PAGE 15
S4K-8x8 INSTRUCTION & OPERATION MANUAL
SYSTEM RESET - FACTORY DEFAULTS
Press
7. SYSTEM RESET Switch Return To Factory default
OFF
>
RECALL
>
ENTER
How to SYSTEM RESET
SYSTEM RESET
To Press RECALL button :
The LCM will show the current stored presets status.
To Press OFF button :
The LCM will show “ SYSTEM RESET ”.
To Press ENTER to confirm entries.
RESET To the FACTORY DEFAULTS
RECA LL
2 2 2 5 5 5 6 6
1 2 3 4 5 6 7 8
S-02
OUTP UT 1 2 3 4 5 6 7 8
SOURCE 1 2 3 4 5 6 7 8
NOTE: factory reset defaults to:
1. Source Destination will be set to 1-1, 2-2, 3-3, etc.
2. Switch matrices stored in memory will be cleared.
3. Lock function will return to un-lock.
4. Aux function will disable and return un-AUX (on select models)
5. ARC function will disable and return SPDIF as output (on select models).
6. EDID will return to FSS® (1080p-2ch mode)
7. Ethernet port will return to DHCP=ENABLED
The switch will reset all customizable values back to factory default.
You must POWER CYCLE the switch for these new values to take effect.

FRONT PANEL
FRONT PANEL
24
POWER SWITCH
DESTINATION SELECT BUTTONS
1
7
The power switch turns the unit on and off. The LED will illuminate red to indicate that the switcher is ON
and is receiving power.
The Switcher will remember that last state during a power cycle.
When power is removed and resorted, the last configuration will be evoked.
INPUT STATUS DISPLAY
4
Input sources 1 to 8 LED illuminates blue to indicate that a video source is present on that input.
Separate outputs 1 thru 8 select buttons are provided for each destination assignment.
Routing can be Source to Destination or one source to multiple destinations.
Example : Press Destination 1,3,5 then press Source 2 will route Input 2 to Output 1,3,5 respectfully.
STATUS DISPLAY
2
Front panel status display shows current matrix routing configuration. This same display also shows
particular configuration settings depending on your current function. In run mode (as shown above),
the display shows each Output (destination ) Channel shows which input (source) is assigned.
IR SENSOR
3
The IR sensor receives IR commands from the supplied remote controller or third party IR emitter.
SOURCE SELECT BUTTONS
5
Separate inputs 1 thru 8 select buttons are provided each source selection.
137
5
PAGE 16 S4K-8x8 INSTRUCTION & OPERATION MANUAL
8
19 INCH EAR MOUNT PAIR
Converts desktop to 19 inch rack mount. Bracket (part # 2U-440L) INCLUDED.
Image shows rack mount bracket attached.
8
6
EDID MODE SELECT BUTTONS
Used to select EDID mode using buttons Source button #1 or #2.
6
POWER
S4K-8x8
1 2
SOURCE STATUS
3 4 5 6 7 8
ALL OFF RECALL MEMORY
EDID ENTERLOCK
1 2 3 5 6 7 8
SOURCE
DESTINATION
SOURCE
DESTINATION
4
1 2 3 5 6 7 8 4
IR
OUT PUT 1 2 3 4 5 6 7 8
SOU RCE 1 2 3 4 5 6 7 8
8x8 HDMI-HDBASET Matrix Switch with Auxiliary Audio I/O
ARC AUX

PAGE 17
S4K-8x8 INSTRUCTION & OPERATION MANUAL
9
FUNCTION KEY - ARC
9
ARC
OUTPUT 1 2 3 4 5 6 7 8
A A A A
FRONT PANEL
FUNCTION KEY - ARC
POWER
S4K-8x8
1 2
SOURCE STATUS
3 4 5 6 7 8
ALL OFF RECALL MEMORY
EDID ENTERLOCK
1 2 3 5 6 7 8
SOURCE
DESTINATION
SOURCE
DESTINATION
4
1 2 3 5 6 7 8 4
IR
OUT PUT 1 2 3 4 5 6 7 8
ARC A A A A
8x8 HDMI-HDBASET Matrix Switch with Auxiliary Audio I/O
ARC AUX
Audio Return Channel (ARC) is a feature that sends audio from the TV back down the HDMI (or HDBaseT) cable to its source device,
in this case, the switcher, Not all displays support ARC; check your Users Guide for additional information. ( Default = ARC Disabled )
The “Audio & ARC” port can support audio from either of three sources.
If the Input Video/Audio Source is HDMI/HDBaseT, the audio can extracted from the embedded signal.
If the Input Audio Source is connected to the external Audio Input, this same audio will be present on the Audio & ARC jack.
If ARC is selected, the audio will be from the destination device (ex; TV).
To Enable the ARC option on a specific Output, perform the follow steps:
- Press the button.
- on the Destination row, Press 1 thru 8 (the button will illuminate).
- Press ENTER button. The new configuration will be stored
The front panel LCD display will now show an “ A “ under the Output port.
- or press ARC again to cancel operation.
To Disable the ARC option on a specific Output, perform the follow steps:
-Press the ARC button
-On the Destination row, press 1 thru 8 (the button will illuminate).
-Press ENTER The pre-set configuration will execute.
The front panel LCD display will be blank under the Output port
- or press ARC again to cancel operation.
Note :
1. Operation will abort if no keys are pressed within 5 seconds.
2. The AUX Audio input only function when a valid HDMI / DVI video signal is present.
Without a video, the AUX audio will not operate.
ARC

FUNCTION KEY - AUX
10
PAGE 18 S4K-8x8 INSTRUCTION & OPERATION MANUAL
FUNCTION KEY - AUX (The audio additional on the “ Audio / ARX” port )
10
AUX X X X X
SOURCE 1 2 3 4 5 6 7 8
FRONT PANEL
POWER
S4K-8x8
1 2
SOURCE STATUS
3 4 5 6 7 8
ALL OFF RECALL MEMORY
EDID ENTERLOCK
1 2 3 5 6 7 8
SOURCE
DESTINATION
SOURCE
DESTINATION
4
1 2 3 5 6 7 8 4
IR
SOU RCE 1 2 3 4 5 6 7 8
AUX X X X X
8x8 HDMI-HDBASET Matrix Switch with Auxiliary Audio I/O
ARC AUX
The AUX FUNCTION feature allows you to replace the embedded HDMI audio signal with an audio signal
that is connected to the switchers Audio AUX Input. Using the AUX function replaces the audio and
does not mix the audio. ( Default = AUX Disabled )
To Enable the AUX option on a specific Output, perform the follow steps:
-Press the AUX button
-On the SOURCE row, press 1 thru 8 (the button will illuminate).
-Press ENTER The new configuration will be stored.
The front panel LCD display will show an “X” under the Source port
AUX
To Disable the AUX option on a specific Output, perform the follow steps:
-Press the AUX button
-On the SOURCE row, press 1 thru 8 (the button will illuminate).
-Press ENTER The pre-set configuration will execute.
The front panel LCD display will be blank under the Output port indicating audio source is that
which is embedded on the HDMI cable.
- or press AUX again to cancel operation.
Note :
1. Operation will abort if no keys are pressed within 5 seconds.
2. The AUX Audio input only function when a valid HDMI / DVI video signal is present.
Without a video, the AUX audio will not operate.
- or press again to cancel operation.

12
PAGE 19 S4K-8x8 INSTRUCTION & OPERATION MANUAL
FUNCTION KEY - EDID (1)
Used to display change current EDID mode.
- press EDID to select new EDID mode or select
- press SOURCE row #1 or #2 Select EDID modes.
- press ENTER to ready memory location.
- or press EDID again to cancel operation.
12
EDID
LEARNING
EDID
3. H24-3D, MULTI AUDIO
FRONT PANEL
FUNCTION KEY - EDID
Operation completes.
Note : Operation will abort if no keys are pressed within 5 seconds.
Select external LEARNING mode
- press EDID to select new EDID mode or select
- press Destination again, press the same Destination #1 thru #8
to learn HDBaseT out port EDID, The EDID for HDBaseT (CATx) has been learned.
- Press ENTER to ready memory location.
- or press EDID again to cancel operation.
Operation completes.
Note : Operation will abort if no keys are pressed within 5 seconds.
FUNCTION KEY - EDID (2)
POWER
S4K-8x8
1 2
SOURCE STATUS
3 4 5 6 7 8
ALL OFF RECALL MEMORY
EDID ENTERLOCK
1 2 3 5 6 7 8
SOURCE
DESTINATION
SOURCE
DESTINATION
4
1 2 3 5 6 7 8 4
IR
OUT PUT 1 2 3 4 5 6 7 8
SOU RCE 1 2 3 4 5 6 7 8
8x8 HDMI-HDBASET Matrix Switch with Auxiliary Audio I/O
ARC AUX

FUNCTION KEY - ALL - OFF - LOCK - ENTER
14 15 16
PAGE 20
S4K-8x8 INSTRUCTION & OPERATION MANUAL
FUNCTION KEY - OFF
14
FUNCTION KEY - LOCK
- Press and hold LOCK button for two seconds lockout the front panel.
- Press and hold LOCK button for two seconds to enable the front panel.
15
FUNCTION KEY - ENTER
16
Disables (mute) video to selected channels. Either destinations.
- Press OFF button followed by any Destination channel.
- Press 1 thru 8 output destination. The display will show " 0 " for the selected
channel indicating no video selected.
13
FUNCTION KEY - ALL
Disables (mute) video on all destinations OR Selects the same source to all destinations.
Option 1
- Press ALL followed by OFF button. The display will show " 0 " indicating all destinations have no video
selected.
Option 2
- Press ALL followed by Source 1 thru 8. The display will show the Source selected.
- Press ENTER The pre-set source selection will be assigned all destinations.
13
Press ENTER to confirm entries.
ALL
OUTPUT 1 2 3 4 5 6 7 8
1 1 1 1 1 1 1 1
OFF 1 0 3 0 5 0 7 0
OUTPUT 1 2 3 4 5 6 7 8
LOCK 1 2 3 4 5 6 7 8
OUTPUT 1 2 3 4 5 6 7 8
FRONT PANEL
POWER
S4K-8x8
1 2
SOURCE STATUS
3 4 5 6 7 8
ALL OFF RECALL MEMORY
EDID ENTERLOCK
1 2 3 5 6 7 8
SOURCE
DESTINATION
SOURCE
DESTINATION
4
1 2 3 5 6 7 8 4
IR
OUT PUT 1 2 3 4 5 6 7 8
SOU RCE 1 2 3 4 5 6 7 8
8x8 HDMI-HDBASET Matrix Switch with Auxiliary Audio I/O
ARC AUX