Smarteh LBT-1.B01 User manual

USER MANUAL
Longo Bluetooth Products
LBT-1.B01
Bluetooth Mesh window / door
sensor
Version 1
SMARTEH d.o.o. / Poljubinj 114 / 5220 Tolmin / Slovenia / Tel.: [phone] / e-mail: [e-mail] / www.smarteh.si

Longo Bluetooth Products LBT-1.B01
Written by SMART H d.o.o.
Copyright © 2021, SMART H d.o.o.
User Manual
Document Version: 1
August, 2022
i

Longo Bluetooth Products LBT-1.B01
STANDARDS AND PROVISIONS: Standards, recommendations,
regulations and provisions of the country in which the devices will
operate, must be considered while planning and setting up electrical
devices. Work on 100 .. 240 V AC network is allowed for authorized
personnel only.
DANG R WARNINGS: Devices or modules must be protected from
moisture, dirt and damage during transport, storing and operation.
WARRANTY CONDITIONS: For all modules LBT-1 – if no modifications
are performed upon and are correctly connected by authorized
personnel – in consideration of maximum allowed connecting power,
warranty of 24 months is valid from the date of sale to the end buyer,
but not more than 36 months after delivery from Smarteh. In case of
claims within warranty time, which are based on material
malfunctions the producer offers free replacement. The method of
return of malfunctioned module, together with description, can be
arranged with our authorized representative. Warranty does not
include damage due to transport or because of unconsidered
corresponding regulations of the country, where the module is
installed.
This device must be connected properly by the provided connection
scheme in this manual. Misconnections may result in device damage,
fire or personal injury.
Hazardous voltage in the device can cause electric shock and may
result in personal injury or death.
N V R S RVIC THIS PRODUCT YOURS LF!
This device must not be installed in the systems critical for life (e.g.
medical devices, aircrafts, etc.).
If the device is used in a manner not specified by the manufacturer,
the degree of protection provided by the equipment may be impaired.
Waste electrical and electronic equipment (W ) must be collected
separately!
LBT-1 devices are developed considering the following standards:
•MC: N 303 446-1
•LVD: N 60669-2-1
Smarteh d.o.o. operates a policy of continuous development.
Therefore we reserve the right to make changes and improvements to
any of the products described in this manual without any prior notice.
MANUFACTUR R:
SMART H d.o.o.
Poljubinj 114
5220 Tolmin
Slovenia
ii

Longo Bluetooth Products LBT-1.B01
Longo Bluetooth Products LBT-1.B01
1.ABBR VIATIONS...............................................................................1
2.D SCRIPTION..................................................................................2
3.F ATUR S......................................................................................3
4.OP RATION....................................................................................4
4.1.Other window / door sensor functions............................................5
4.2.Operation parameters................................................................6
5.INSTALLATION.................................................................................9
5.1.Mounting instructions...............................................................11
5.2.Maintenance..........................................................................13
5.3.Module labeling......................................................................14
6.SYST M OP RATION ........................................................................15
6.1. rror codes...........................................................................15
6.2.Interference warning ...............................................................15
7.T CHNICAL SP CIFICATIONS...............................................................16
8.CHANG S ....................................................................................17
9.NOT S.........................................................................................18
iii

Longo Bluetooth Products LBT-1.B01
1.ABBREVIATI NS
L D Light mitted Diode
PLC Programmable Logic Controller
OpCode Message Option Code
LBT-1.GWx x means different number of gateway type
i.e. LBT-1.GW1 Modbus RTU Bluetooth Mesh
gateway
1

Longo Bluetooth Products LBT-1.B01
2.DESCRIPTI N
LBT-1.B01 Bluetooth Mesh window / door sensor is designed to work with any window or door while
for detection of opening or closing is performed with an external magnet, which is delivered
together with the sensor.
Window sensor and a magnet can primary be mounted with double sided glue tape or, in addition,
with a screws, delivered together.
Window sensor transmits information about open/close status, as well as also the information about
battery voltage level. LBT-1.B01 Bluetooth Mesh window sensor can only operate in the Bluetooth
Mesh network with Smarteh LBT-1.GWx Modbus RTU Bluetooth Mesh gateway connected to the main
control device as Smarteh LPC-3.GOT.012 7" PLC based Touch panel. Any other PLC with Modbus RTU
communication and Smarteh LBT-1.GWx Bluetooth Mesh gateway connected can also serve as main
control device. Beside Smarteh Bluetooth Mesh devices, other standard Bluetooth Mesh devices can
be integrated into above mentioned Bluetooth Mesh network. More than a hundred Bluetooth Mesh
devices can be provisioned and can operate in a single Bluetooth Mesh network.
N TE: Alkaline AA type of batteries (LR6) are not supplied together with the product.
WARNINGS:
Explosion due to fire or short circuit, even with discharged batteries:
• Risk of injury due to flying parts.
• Prevent the batteries to be in contact with water.
• Do not damage the batteries.
• Do not heat batteries over 85°C.
Leakage of electrolyte:
• Handle damaged batteries only wearing suitable protective gloves.
Otherwise severe burns are possible.
• In case of contact with electrolyte, rinse eyes immediately with a lot of water. Visit the doctor.
Falling objects:
• Overhead installation may result in injury from falling objects.
bserve also following:
• Pay attention on battery polarity (+/-).
• The batteries must be new and undamaged.
• Do not mix new and used batteries.
• Store, transport and dispose of the batteries in compliance with local requirements,
regulations and laws. Also observe the instructions of the battery manufacturer.
• Dispose of empty batteries in designated collection points.
2

Longo Bluetooth Products LBT-1.B01
3.FEATURES
Figure 1: LBT-1.B01
Table 1: Technical data
Communication standard: Bluetooth Mesh is a low power wireless mesh protocol and allows
device to device communication and device to main control device communication.
Radio frequency: 2.4GHz
Range for direct connection: < 30m, depending on application and building.
Tip: with mesh topology bigger distances can be achieved.
Power supply: 2 batteries 1.5V AA type commercially available, use alkaline batteries only (LR6).
Do not use any type of rechargeable battery. Constructed for full year operation.
Protection degree: IP20
Working temperature: 0 .. 50 °C
Storage temperature: -20 .. 60 °C
Type of casing: ABS
Status indicator: red and green L D
Window/door position detection: Contact less, by using magnet
3

Longo Bluetooth Products LBT-1.B01
4. PERATI N
LBT-1.B01 Bluetooth Mesh window sensor is designed to work with any window or door while for
detection of opening or closing is performed with an external magnet, which is delivered together
with the sensor.
Window sensor transmits information about open/close status, as well as also the information about
battery voltage level. LBT-1.B01 Bluetooth Mesh window sensor can only operate in the Bluetooth
Mesh network with Smarteh LBT-1.GWx Modbus RTU Bluetooth Mesh gateway connected to the main
control device as Smarteh LPC-3.GOT.012 7" PLC based Touch panel. Any other PLC with Modbus RTU
communication and Smarteh LBT-1.GWx Bluetooth Mesh gateway connected can also serve as main
control device. Beside Smarteh Bluetooth Mesh devices, other standard Bluetooth Mesh device can
be integrated into above mentioned Bluetooth Mesh network. ven thousands of Bluetooth Mesh
devices can be provisioned and can operate in a single Bluetooth Mesh network.
Figure 2: LBT-1.B01 device connection
Figure 3: Bluetooth Mesh system topology
4

Longo Bluetooth Products LBT-1.B01
4.1. ther window / door sensor functions
• Anti freeze: the sensor itself cannot detect, if the room temperature falls below 6°C, but
information about open window can be used as information for further actions.
To prevent from freezing, it is recommended to use Smarteh LBT-1.BA1 valve actuator or some
other heat source, that can be controlled through the automation system
(using Bluetooth Mesh network,...).
• pen window or balcony door: nergy saving function during window or balcony door
open can be implemented by using Smarteh LBT-1.B01 window / door sensor and main control
device as LPC-3.GOT.012 7" PLC based Touch panel.
• Factory reset: This function will delete all Bluetooth Mesh network parameters stored on
LBT-1.B01 window / door sensor and will restore to the conditions of the initial programming,
ready for provisioning (see description on page 8).
N TE: When voltage of two installed AA batteries in series is lower than 2.2V, LBT-1.B01 window /
door sensor detects low battery condition. If batteries are not replaced soon, window sensor will
switch off. Voltage level of the batteries can be monitored regularly i.e. on the Smarteh
LPC-3.GOT.012 7" PLC based Touch panel.
5

Longo Bluetooth Products LBT-1.B01
4.2. peration parameters
LBT-1.B01 Bluetooth Mesh window / door sensor accepts a set of operation codes as specified in
below tables 2 to 4.
LBT-1.B01 Bluetooth Mesh window / door sensor is communicating with main control device as
Smarteh LPC-3.GOT.012 via Smarteh LBT-1.GWx Modbus RTU Bluetooth Mesh gateway.
All communication between main control device as LPC-3.GOT.012 or similar is performed by using
Modbus RTU communication. Individual Bluetooth Mesh node configuration data should be observed
by using network provisioning tool.
Table 2: Modbus RTU to Bluetooth Mesh gateway
Holding registers
Memory Type Function Variable description Range Values
40010 uint16 xecute command
xecute command for Read
and/or Write on rising and
falling edge
0..1
0..2
Write: 0->1, 1->0
Read: 0->2, 2->0
40011 uint16 Destination address*
Destination node address.
Can be unicast, group or
virtual address
0..65535 0..65535
40012 uint16 lement index* Sending node model
element index 0..65535 0..65535
40013 uint16 Vendor ID* Vendor ID of the sending
node model 0..65535 0..65535
40014 uint16 Model ID* Model ID of the sending
node model 0..65535 0..65535
40016 uint16 Virtual address index* Index of the destination
Label UUID 0..65535 0..65535
40017 uint16 Application key index* The application key index
used 0..65535 0..65535
40018 uint16 Option code** Refer to option code table 0..63 0..63
40019 uint16 Payload byte length** Refer to option code table 1..10 1..10
40020 uint16 Payload word[0]** Refer to option code table 0..65535 0..65535
40021 uint16 Payload word[1]** Refer to option code table 0..65535 0..65535
40022 uint16 Payload word[2]** Refer to option code table 0..65535 0..65535
40023 uint16 Payload word[3]** Refer to option code table 0..65535 0..65535
40024 uint16 Payload word[4]** Refer to option code table 0..65535 0..65535
* Observed from network provisioning tool
** User defined parameters, refer to option code table
6

Longo Bluetooth Products LBT-1.B01
Table 3: Modbus RTU to Bluetooth Mesh gateway
Input registers
Memory Type Function Variable description Range Values
30010 uint16 Messages pending Number of messages pending in
receiving buffer 0..10 0..10
30011 uint16 Destination
address status
Destination node address. Can
be unicast, group or virtual
address
0..65535 0..65535
30012 uint16 lement index
status
Sending node model element
index 0..65535 0..65535
30013 uint16 Vendor ID status Vendor ID of the sending node
model 0..65535 0..65535
30014 uint16 Model ID status Model ID of the sending node
model 0..65535 0..65535
30015 uint16 Source address Unicast address of the node
model which sent the message 0..65535 0..65535
30016 uint16 Virtual address
index status
Index of the destination Label
UUID 0..65535 0..65535
30017 uint16 Application key
index status
The application key index
used 0..65535 0..65535
30018 uint16 Option code
status Refer to option code table 0..63 0..63
30019 uint16 Payload length
status Refer to option code table 1..10 1..10
30020 uint16 Payload word[0]
status Refer to option code table 0..65535 0..65535
30021 uint16 Payload word[1]
status Refer to option code table 0..65535 0..65535
30022 uint16 Payload word[2]
status Refer to option code table 0..65535 0..65535
30023 uint16 Payload word[3]
status Refer to option code table 0..65535 0..65535
30024 uint16 Payload word[4]
status Refer to option code table 0..65535 0..65535
7

Longo Bluetooth Products LBT-1.B01
Table 4: Window sensor LBT-1.B01 option codes
ption
code Type Function Variable description Range Values
1 uint16 FW version status Firmware version status 0 .. 65535 0 .. 65535
2 uint16 Operation mode set Node operation mode
selection 0 .. 5
0 = Not used
1 = Not used
2 = Not used
3 = Not used
4 = Reset
5 = Factory reset
6 uint16 Vandal switch
alarm status
Node vandal switch
status 0 .. 1 0 = Not active 1 = Active
7 uint16 Open / Close
status Node status 0 .. 1 0 = Close 1 = Open
8 uint16 Battery voltage
status Battery voltage level 0 .. 330 0,00 .. 3,30V
9 uint16 Wake up interval
set
Node wake up from
sleep mode interval 0 .. 65535 0 = Always on 1 .. 65535 sec.
10 uint16 Wake up interval
status
Node wake up from
sleep mode interval
status
0 .. 65535 0 = Always on
1 .. 65535 sec.
11 uint16 rror codes status
Bit0 = No error
Bit1 = Not used
Bit2 = Battery low
Bit3 = Not used
Bit4 = Not used
8

Longo Bluetooth Products LBT-1.B01
5.INSTALLATI N
Table 5: LEDs & Inputs
L D1 Red L D
1x blink – empty battery
2x blinks – network/friend lost
3x blinks – unprovisioned node
L D2 Green L D 1x blink – normal operation. It's also feedback for S1 (reed
contact) when activated with magnet
S1 Reed contact Mode setting contact
Inside 5 sec time window, perform corresponding number of
swipes in duration of not less than 200 ms with permanent
magnet close to the window sensor S1 reed contact position.
Following window sensor action or mode will be set:
number of swipes Action
=====================================
5x Factory reset
S2 Switch Vandal switch: close = not active, open = active
S3 Reed contact For window/door magnet
Figure 4: LBT-1.B01 L Ds and switches position
9

Longo Bluetooth Products LBT-1.B01
Table 6: Battery
Bat.1 Battery Alkaline AA/LR6 1,5V high capacity battery, non rechargeable
Bat.2 Battery Alkaline AA/LR6 1,5V high capacity battery, non rechargeable
Figure 5: LBT-1.B01 battery position
10

Longo Bluetooth Products LBT-1.B01
5.1.Mounting instructions
Figure 6: Housing dimensions
Dimensions in millimeters.
Figure 7: Mounting positions
Before mounting the sensor and magnet to provided place, it's necessary to check, that mounting
position will give best sensing performance between sensor and magnet (see pictures above). Pay
attention on the gap between each other (not more than 5mm) and on the center positioning (stripe
lines should be aligned).
11

Longo Bluetooth Products LBT-1.B01
Figure 8: Installation flowchart
1. Check if sensor will be fixed with double sided glue tape or with screws (can also be fixed
both).
2. Once sensor is mounted to provided place, insert two AA batteries and firmly close the
cover. In addition, also cover can be fixed with a screw and hidden by small plastic cap,
delivered together.
3. Mount the magnet in a way to get best sensing performance.
4. After few seconds Green or Red L D starts to blink, please see flowchart above for details.
5. If sensor is not provisioned (Red L D will blink 3x), the provisioning procedure have to be
started (contact producer for more details*).
6. Once provisioning is finished, sensor will continue with normal mode of operation and this
will be indicated as Green L D blinking once per 10 sec.
*Note: Smarteh Bluetooth Mesh products are added and connected to a Bluetooth Mesh network by
using standard provisioning and configuration mobile apps tool such as nRF Mesh or similar.
For further information, please contact producer for more details.
12

Longo Bluetooth Products LBT-1.B01
5.2.Maintenance
The LBT-1.B01 window / door sensor is maintenance free. Only two AA batteries require
replacement with new one when empty. On main control device i.e. LPC-3.GOT.012, the indication
for replacing the batteries will become active. If batteries will not be replaced approximately in two
months after battery warning appear for the first time, window / door sensor will switch off.
While replacing the batteries, it's recommended that LBT-1.B01 window / door sensor and the
magnet remain mounted. However, replacing of batteries is also possible if/when sensor is
dismounted. In this case please follow instructions from capture 5 – INSTALLATION. For optimal
performance, the usage of alkaline AA batteries (LR6) with high capacity is recommended.
Figure 9: Screw position
1. Remove a screw (if fasten) by using Torx T10 screw driver and than open the cover.
NOT : screw may be hidden under small plastic cap.
2. Take both batteries out of the battery holder.
3. Insert two new high capacity batteries alkaline AA/LR6, PAY ATT NTION ON POLARITY!
4. Close the cover and, if necessary, also fasten the screw by using Torx T10 screw driver.
Insert also small plastic cap, if it was removed before.
5. The window sensor will automatically start to re-establish the connection, if Bluetooth Mesh
network is available.
Unsuccessful connecting to the Bluetooth Mesh network will be shown on sensor itself (red L D1 will
blink 2x) and also on the main control device i.e. LPC-3.GOT.012. In this case please refer to
chapter 6 – SYSTEM OPERATION / Error code for troubleshooting.
13

Longo Bluetooth Products LBT-1.B01
5.3.Module labeling
Figure 10: Label
Label (sample):
Label description:
1. XXX-N.ZZZ - full product name,
• XXX-N - product family,
• ZZZ.UUU – product,
2. P/N: AAABBBCCDDDEEE - part number,
• AAA - general code for product family,
• BBB - short product name,
• CCDDD - sequence code,
• CC - year of code opening,
• DDD - derivation code,
• EEE – version code (reserved for future HW and/or SW firmware upgrades),
3. S/N: SSS-RR-YYXXXXXXXXX - serial number,
• SSS – short product name,
• RR – user code (test procedure, e.g. Smarteh person xxx),
• YY – year,
• XXXXXXXXX – current stack number,
4. D/C: WW/YY - date code,
5. WW – week and,
6. YY – year of production.
Optional:
• MAC,
• Symbols,
• WAMP,
• Other.
14
XXX-N.ZZZ.UUU
P/N: AAABBBCCDDDEEE
S/N: SSS-RR-YYXXXXXXXXX
D/C: WW/YY

Longo Bluetooth Products LBT-1.B01
6.SYSTEM PERATI N
LBT-1.B01 window / door sensor detects magnet position movement and according to presence of
the sensor, sends to main control device LPC-3.GOT.012 status Open/Close in approx. 1 sec delay.
Beside Open/Close status, LBT-1.B01 window / door sensor also sends battery voltage and S2 vandal
switch alarm status.
6.1.Error codes
In case of LBT-1.B01 window / door sensor malfunction or communication error with main control
device, corresponding message is shown on main control device LPC-3.GOT.012. rror codes cannot
be acknowledged on the main control device, but they are shown as long as the errors are active
and will disappear automatically once normal operation is reached back.
Error Reason Solution
Open/Close
status doesn't
work
• Communication lost
• Magnet is not aligned correctly with a
sensor
• Check interference warning in the
section below.
• Align magnet correctly with a sensor
and gap between should also not be
bigger than 5mm.
Provisioning
failed
• LBT-1.B01 window / door sensor is not
able to connect to main control device
LPC-3.GOT.012
• Too large distance, out of range
• BL RF chip failure
• Check and adjust settings and restart
the pairing process with provisioning
tool
• Decrease the distance between LBT-
1.B01 window / door sensor and LPC-
3.GOT.012
Communication
lost
• The current connection to the LPC-
3.GOT.012 is not available any more
• Too long distance, out of range
• Check the power supply (battery)
• Decrease the distance
• No new pairing is needed while
devices will be automatically
connected, once available back to the
Bluetooth Mesh network
6.2.Interference warning
Common sources of unwanted interference are devices that generate high frequency signals. These
are typically computers, audio and video systems, electronics transformers, power supplies and
various ballasts. The distance of the LBT-1.B01 window / door sensor to the above mentioned
devices should be at least 0.5m or greater.
WARNING:
• In order to protect plants, systems, machines and network against cyber threats, necessary
to implement and continuously maintain up to date security concept.
• You are responsible for preventing unauthorized access to your plants, systems, machines and
networks and they are allowed to be connected to Internet only, when security measures like
firewalls, network segmentation, … are in place.
• We strongly recommend the updates and usage of latest version. Usage of version that are no
longer supported may increase the possibility of cyber threats.
15

Longo Bluetooth Products LBT-1.B01
7.TECHNICAL SPECIFICATI NS
Table 7: Technical specifications
Power supply 2 high capacity batteries alkaline AA type (LR6)
Battery life > 1 years
RF communication interval When magnet position to the window sensor is
changed or typically every 10min
Life cycle status and monitor capabilities Yes
Max. power consumption 0,01 W
Mounting fixation double sided glue tape and/or with a screw
Dimensions (L x W x H) 147 x 22 x 24 mm
Weight (with two AA batteries) 100 g
Ambient temperature 0 to 50 °C
Ambient humidity max. 95 %, no condensation
Maximum altitude 2000 m
Mounting position Any
Transport and storage temperature -20 to 60 °C
Pollution degree 2
Over voltage category II
lectrical equipment Class II (double insulation)
Protection class IP 20
16