SmartPro Aura User manual

USER’S MANUAL v3.0
SmartPro Aura
Synthetic Diamond Scanner
V2

CONTENTS
I. DISCLAIMERS, EXCLUSIONS, AND LIMITATIONS OF LIABILITY…..p. 3
II. ABOUT SMARTPRO AURA……………………………………………… p. 3
III. FEATURES AND ADVANTAGES……………………………………….. p. 4
IV. PRODUCT SPECIFICATIONS…………………………………………… p. 4
V. TESTER OVERVIEW……………………………………………………… p. 5
VI. ACCESSORIES……………………………………………………………. p. 8
VII. POWERING DEVICE……………………………………………………… p. 9
VIII. TESTER LIGHT INDICATORS…………………………………………… p. 10
IX. CONTROL SETTINGS…………………………………………………….. p. 11
X. TESTING / DETECTION………………………………………………….. p. 12
XI. TEST RESULTS…………………………….….…………………...……... p. 14
XII. TEST CERTIFICATE……………………………………………………… p. 17
XIII. SHARING IMAGES / TEST CERTIFICATE…………………………….. p. 21
XIV. PRINTING IMAGES / TEST CERTIFICATE……………………………. p. 21
XV. IMAGE / FOLDER GALLERY……………………………………………. p. 22
XVI. SETTINGS PAGE………………………………………………………….. p. 24
XVII. SAFE HANDLING / MAINTENANCE……………………………………. p. 25
XVIII. TROUBLESHOOTING ……….…………………………………………… p. 26
XIX. TESTER THUMBSCREW ASSEMBLY …………………………………..p. 27

I. DISCLAIMERS, EXCLUSIONS, AND LIMITATIONS OF LIABILITY
Please read and note SMARTPRO WARRANTY TERMS AND CONDITIONS
as stated in the warranty card. SmartPro warranty for its subject to proper use
by its user following all the terms and conditions as stated in the relevant user
manual and shall cover only manufacturing defects.
Due to continuous product improvement, SmartPro reserves the right to
revise all documents including the right to make changes to the user manual
without notice and without obligation to notify any person of such revisions or
changes. Users are advised to check SmartPro’s website
http://www.smartproinstrument.com.
SmartPro shall not be responsible for any damage or loss resulting from the
use of the product or user manual, and under no circumstances shall
SmartPro, its manufacturer or any of its subsidiaries, licensors, distributors,
resellers, servants and/or agents be liable for any direct or indirect damages
resulting from the use of this product.
To the maximum extent permitted by applicable law, under no circumstances
shall SmartPro, its manufacturer or any of its subsidiaries, licensors,
distributors, resellers, servants and/or agents be liable for any special,
incidental, consequential or indirect damages howsoever caused.
Smartpro Aura referred to in this user manual is provided and/or sold on the
“as is” basis. Except as required by applicable law, no warranties of any kind,
expressed or implied, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose.
II. ABOUT SMARTPRO AURA
Congratulations on having your SmartPro Aura (SPAU). The first
Synthetic Diamond Screener that can screen automatically for mounted
jewelry and can also be used to test loose stones with various test results
such as Natural Diamond, CVD Synthetic Diamond, and HPHT Synthetic
Diamond.
- 3 -

III. FEATURES AND ADVANTAGES
1. FEATURES
Able to test Mounted Jewelry and loose stones
Able to Detect as small as 0.002 ct. stones
Built-in high-end Smartphone with high camera resolution
Low current consumption
360-degree view for Rings and Jewelry
Test Result Sharing by email
Manually observe stones on UV
Auto Detection Mode View
Able to test stones inside a transparent plastic bag for bulk testing
2. ADVANTAGES
Automated test results
Auto-generated test result certification
No External Computer Needed
Teamviewer Online Support
Screen Sharing
Easy Test Result Viewing
Test Certificate Logo and Company Details Customization
Able to share test results on a single e-mail
IV. PRODUCT SPECIFICATIONS
Stones Testing Capabilities
Natural Diamond
CVD Synthetic Diamond
HPHT Synthetic Diamond
Moissanite (no fluorescent image)
Stone Colors (capable to detect)
Colorless to Near Colorless (D-K)
Stone Size (capable to detect)
0.002 carat and above
Time Duration per test
17 secs. for Quick Test
93 secs. for 360 Test (total of 4 tests)
Loose Stone Tray Size (camera view)
64 x 64 mm
Tester Body Dimensions
230 x 301.5 mm
Tester Weight
Approx. 5.0 Kg
Body Color
Red with Black
Power Supply Input
100-240 VAC, 1.4A
Power Fuse
3A
- 4 -

A. Aura Carrying Bag
B. Smartpro Aura Tester
C. AC Power Cable
D. Loose Stone Tray 1 (SPALST)
E. Loose Stone Tray 2 (SPALST2)
F. Jewelry Tray
G. Ring Attachment 20mm
H. Ring Attachment 25mm
I. Bracelet Attachment 55mm
J. Bracelet Attachment 65mm
K. Tester User’s Manual
L. Warranty Certificate Card
M. International Warranty Card
A
B
C
G
H
I
J
K
L
M
E
F
D
Power Cable Type
IEC C13
Screen Device
Samsung S21FE
Lamp Life
Approximately 675,000 tests
Operating System
Android
Screen Size
6.4 Inches
Screen Resolution
1080x2400pixels
Device Memory
8GB RAM
Mobile Battery
Auto-charging
Ventilation Requirements
Do not obstruct the ventilation holes
V. TESTER OVERVIEW
1. Tester Parts and Accessories
-5 -

2. Tester Overview
-6 -

3. Mobile Screen Overview
-7 -

VI. ACCESSORIES
1. Loose Stone Tray – view size: 64 x 64 mm
2. Ring / Jewelry Tray - 10 slots for ring and earrings.
For Bulk, Loose Stones / Stones inside Transparent Plastic
Ring and Earing
slots
Camera view
Tray Code: SPALST2
Tray Code: SPALST
For Big and Separated Stones
- 8 -

3. Jewelry Attachment (for 360 views)
i. Ring attachment with 20mm and 25mm diameter
ii. Bracelet attachment with 55mm and 65mm diameter
VII. POWERING DEVICE
1. Turning ON the AURA Box.
i. Connect the Power Cable into the Inlet Power Socket at the backside
of AURA and the other end of cable plug to the Power Outlet.
ii. Switch ON the Inlet Power Switch.
-9 -

2. Turning ON the built-in mobile.
Click and hold the Mobile Switch at the
right side of AURA until the mobile
screen opens.
VIII. TESTER LIGHT INDICATORS
1. UV Lamp Indicator
i. No light – indicates that the UV Lamp is turned OFF.
ii. Blue light – indicates that the UV Lamp is turned ON.
Note: UV lamp will automatically turn OFF when the Door
opens.
2. Door Indicator
i. No light – indicates that the door of the tester is fully
closed.
ii. Red light – indicates that the door of the tester is
opened.
3. Power Indicator
i. No light – indicates that the tester is switched OFF.
ii. Blinking Green light – indicates that the tester is turned
ON but it is not connected to the mobile phone.
iii. Stable Green light – indicates the tester is turned ON
and ready to use.
- 10 -

IX. CONTROL SETTINGS
Users may control the Daylight ON and OFF as well as the UV Lamp to
manually observe stones. Camera Focus and 360-view may also adjust for a
better angle view.
-11 -

X. TESTING / DETECTION
There are many types of mounting of stones in Jewelries and some are
selling loose. So we created a tester that can test in almost all types of
settings. Here are the available Detection Options:
1. Quick Test Mode – this mode is capable to test the following:
Bulk Stones on Tray
Bulk Stones in Clear Plastic
Jewelries on Tray
- 12 -

Notes:
Do not place stones or Jewelry over the Detection Area (black foam
area).
Arrange the Jewelries on the same height as possible
to get a better camera focus for the best detection
process.
2. 360 Degrees Detection - used to test mounted stones such as
rings, necklaces, and bangles that are attached to a built-in motor to
rotate in 360 degrees view. There will be 4 angle tests with auto-
generated test results and certificates by one click only.
Jewelry is placed
within the
detection area.
Jewelry is
placed over the
detection area.
Jewelries are placed with
the same height as
possible.
Jewelries are placed with
not the same height.
- 13 -

XI. TEST RESULTS
1. Quick Test Mode Results
-14 -

i. Test Result Analysis
Stones with Red Marks = Synthetic / Lab Grown Diamond
Stones without Red Marks = Natural Diamond / Unknown Stones
Here are the Fluorescent Reference Images:
Diamond
Cubic Zirconia (CZ)
CVD Synthetic
Note: If the User still doubts determining the type of the Stones
whether the stone is Synthetic or Natural, do a Longwave Fluorescent
test using a regular UV light source. Lab-Grown Diamonds will not
fluoresce unlike about 25% to 30% of Natural Diamonds will do.
Important:
No red mark stones must compare with the given fluorescent reference
images to confirm its type.
- 15 -

ii. Identifying Stones by Fluorescent Image and Short Phos.
Image.
2. 360 Detection
The same process as Quick Test but using a Jewelry attachment to
hold Rings and Jewelries. A 4 in 1 detection which the motor
automatically rotates every 90 degrees and test.
.
4 detection
results available.
Select one to
view one set of
result.
Tap the “Other
Angle” select the
different degree
view.
-16 -

XII. TEST CERTIFICATE
To show the test result professionally, Smartpro has made an auto-generated
Test Certificate that will be found in the Preview Page after the detection process.
This Certification may send directly to any email address by clicking the share
button. Users may also save this test certificate in the Gallery together with the
other related captured images. The file will be saved in a pdf format.
1. CHOOSING THE CERTIFICATE TYPE
User may choose, change or edit the Logo and the Company Details
to show on the certificate.
i. Default - Smartpro default logo and company details.
ii. Custom 1 – 1st user Custom logo and company details picture.
iii. Custom 2 – 2nd user Custom logo and company details picture.
Changing Logo and Company Details sequence:
a. Click Custom 1.
b. Click Company Logo.
c. Choose and select where the picture/logo is located
Note: The new logos or pictures to be uploaded should be
already saved on the Phone’s files/gallery or already on the
gmail/Outlook account.
d. Crop the image then click the check symbol on the upper
right of the screen to proceed.
-17 -

e. Follow the same steps as for the Company Logo for
changing the Company Details Logo.
Customized Certificate Logo Sample:
-18 -

2. REGISTRATION
Fill-up necessary details on registration page to have better
information of the test results. This certificate may save in the gallery,
print and share through email.
-19 -