Avision AV810CPlus User manual

User’s Manual
For AV810CPlus/AV820CPlus/AV830CPlus
Document Imaging Scanner
Doc. No. 250-0332-E V1.0
Avision Inc.

ii
Trademarks
Microsoft is a U.S. registered trademark of Microsoft Corporation.
Windows and MS-DOS are trademarks of Microsoft Corporation.
IBM, PC, AT, XT are registered trademarks of International Business
Machines Corp.
Other brands and product names herein are trademarks or registered
trademarks of their respective holders.
Copyright
All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated
into any language or computer language, in any form or by any means,
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise, without the prior written permission of Avision Inc.
Material scanned by this product may be protected by governmental
laws and other regulations, such as copyright laws, the customer is
solely responsible for complying with all such laws and regulations.

iii
Warranty
The information contained in this document is subject to change
without notice.
Avision makes no warranty of any kind with regard to this material,
including, but not limited to, the implied warranties of fitness for a
particular purpose.
Avision shall not be liable for errors contained herein or for
incidental or consequential damages in connection with the
furnishing, performance, or use of this material.

iv
FCC Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communication. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
− Reorient or relocate the receiving antenna.
− Increase the separation between the equipment and receiver.
− Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
− Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION: To assure continued compliance, (example - use only shield
interface cables when connecting to computer or peripheral devices). Any
changes or modifications not expressly approved by the manufacture of this
device could void the user's authority to operate the equipment. This device
complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may
cause undesired operation.
Safety Regulation
EMI Regulation
UL1950, Third edition
EN 60950
IEC 60950
FCC Part 15 Subchapter J Class B
DOC Class B (Canada)
CE
Responsible Party: Avision Labs, Inc.
Telephone No.: [phone]

v
Table of Contents
1. INTRODUCTION ......................................................1-1
2. SCANNER INSTALLATION ....................................................2-1
2.1 PRECAUTIONS.........................................................................................2-1
2.2 SCANNER UNPACKING........................................................... 2-1
2.3 ADF PAPER CHUTE INSTALLATION .......................................... 2-5
2.4 DOCUMENT LOADING ........................................................... 2-7
2.5 CONNECTING THE CABLES ..................................................... 2-9
2.6 INSTALLATION OF THE SCSI CARD..........................................2-11
2.6.1 PC USERS..................................................................2-11
2.6.2 MAC USER.................................................................2-12
3. SCANNER DRIVER INSTALLATION..................................3-1
3.1 MAC USERS......................................................................... 3-1
3.2 PC USERS........................................................................... 3-4
3.2.1 WINDOWS 3.1 OR WINDOWS 3.1X ................................... 3-4
3.2.2 WINDOWS 95/WINDOWS 98 OR WINDOWS NT4.0 ............... 3-5
4. SCANNER OPERATION...............................................4-1
4.1 STARTING YOUR FIRST SCAN FROM WITHIN A TWAIN OR A PLUG-
IN APPLICATION ......................................................................................4-1
4.2 USING AVISION SCANNER DRIVER USER INTERFACE ..................... 4-5
4.2.1 CHOOSING YOUR SCANNING SOURCE................................4-5
4.2.2 DETERMINING YOUR RESOLUTION.................................. 4-6
4.2.3 SELECTING A PROPER IMAGE TYPE................................. 4-8
4.2.4 ENHANCING YOUR IMAGE ............................................4-13
4.2.5 VIEWING THE IMAGE TOOL...........................................4-24
4.2.6 OTHER TOOLS...........................................................4-25
4.2.7 STARTING FINAL SCAN.................................................4-26

vi
5. CARE AND MAINTENANCE...........................................5-1
5.1 CLEANING THE ADF .............................................................. 5-1
5.2 CLEANING THE GLASS........................................................... 5-3
5.3 REPLACING THE ADF DETACHABLE PAD MODULE........................ 5-4
6. TROUBLESHOOTING.................................................6-1
6.1 FREQUENTLY ASKED QUESTIONS............................................. 6-1
6.2 PAPERJAM IN THE ADF.......................................................... 6-4
6.3 TECHNICAL SERVICE.............................................................. 6-6
7. SPECIFICATIONS.....................................................7-1

1-1
1. INTRODUCTION
Congratulations on your purchase of theAvision document scanner.
Avision is one of the leading company to make high quality document
scanner.
To ensure the optimum performance of the scanner, please take a few
minutes to read through this manual before you install and operate the
new scanner. The manual contains important information on how to
unpack, install, operate, and maintain the scanner properly. Figure 2-1
in below shows how the scanner is packed. Please check if all items are
included.

1-2
Figure 1-1 Scanner Package
1. Power Adapter
2. Power Cable
3. SCSI Cable
4. Output Paper Tray
5. User’s Manual, Software CD
6. SCSI Card
7. Scanner main unit
8. Cushion
9. Carton
1
2
3
4
6
5
7
8
9

2-1
2. SCANNER INSTALLATION
2.1 PRECAUTIONS
v Keep the scanner out of direct sunlight. Direct exposure to
the sun or excessive heat may cause damage to the unit.
v Do not install the scanner in a humid or dusty place.
v Be sure to use the proper AC power source.
v Only use the AC adapter (model name SA60-24 made bySino
America) included with the machine. Using other AC adapters may
damage the machine and therefore void the warranty.
v Place the scanner securely on an even, flat surface. Tilted or
uneven surfaces may cause mechanical or paper-feeding problems.
v Keep the shipping box and the material in case you may need to
ship the scanner again.
2.2 SCANNER UNPACKING
Please unpack the scanner carefully. If any item is missing or damaged,
please contact your authorizedAvision dealer immediately.
Remove the shipping retainer:
1. Place the scanner on its side as shown to reveal the shipping
retainer as shown in Figure 2-1.
2. Unscrew the retainer screw.
3. Pull out the shipping retainer and put it in the “use position”(See
Figure 2-2) and secure it with the screw.
4. Lay down the scanner on the desk for normal operation.

2-2
Figure 2-1 Remove the shipping retainer.
Figure 2-2 Fasten the shipping retainer.
“Shipping
Position”
“Use
Position”

2-3
Refit the shipping retainer:
Whenever you need to transport the scanner, please follow the
instructions below:
1. Turn off the scanner.
2. Raise the document cover. You can see clearly the flatbed glass as
well as the reading engine.
3. Turn on the scanner. At this moment, the reading engine will move
a few inches forward and stay there for a few seconds. Turn off
the scanner during this pause.
4. Raise the scanner high enough to unscrew the shipping retainer
from the “use position” and fix it in the “shipping position.”
SCSI ID:
When you have several devices on a SCSI chain, you may need to adjust
the SCSI ID selector setting located on the back of the scanner(See
Figure 2-3). This setting assigns a specific "device ID" to the scanner. If
the ID number is duplicate with an existing SCSI device, please select a
new ID.
Note: The factory setting for the scanner is ID# 6. Usually, ID# 0 is
assigned to an internal hard disk drive, and ID# 7, to SCSI adapter or host.
ID# 8 and #9 are not in use actual.
Setting Terminator
The scanner is equipped with a built-in terminator switch on the rear of
the scanner. (See Figure 2-3) Turn the terminator switch on if the
scanner is to be connected to the computer as the only or the last SCSI
device. Turn the terminator switch off if the scanner is to be located
between the computer and other SCSI device.

2-4
Figure 2-3 SCSI ID setting/Terminator switch
SCSI ID Selector
SCSI Terminator Switch

2-5
2.3 ADF PAPER CHUTE INSTALLATION
1. Raise the document cover to about 45 degrees.
2. Place the ADF paper chute to about 45 degrees. Insert the ADF
paper chute to auto feeder holes on the document cover as shown
in Figure 2-4.
3. Pull out the wire leg under the paper chute.
4. Pull out the paper chute extension to the length you wish.
Figure 2-4 Install the ADF paper chute
ADF Paper Chute
Paper Chute
Extension
Document
Cover

2-6
ADF output paper rack installation
1. Hold the output paper rack some 30 degrees as shown in Figure
2-5.
2. Insert the three clasp-joints on the output paper rack in their
respective places on the ADF.
3. Release the paper rack gently. Make sure the rack is firmly
attached to the ADF.
4. Pull out the output paper rack extension to the length you
want.
Figure 2-5 Install the ADF output paper rack
ADF Output
Paper Tray

2-7
2.4 DOCUMENT LOADING
For flatbed scanning, see Figure 2-6.
Figure 2-6 Lay the paper on the scanner
Document
Cover
Original
Document
Glass
Reference
Mark
Reference
Frame

2-8
Standard paper size should feed easily through the scanner. To prevent
occasional paper jam when automatically feeding multiple documents,
loosen the paper before loading(See Figure 2-7).
Figure 2-7 Use ADF to load multiple documents
Left Guide
Right Guide
Document
Balance Wire

2-9
2.5 CONNECTING THE CABLES
Be sure the scanner power is switched off.
Connect the power cable and signal cable as Figure 2-8 and Figure 2-9.
Turning on the Power
The power is controlled by a toggle switch on the side of the
scanner. To turn on the scanner, press the switch toward "1."
At this moment, the POWER LED should light up. If not, check the
power.
Scanner Diagnostics
The scanner has a built-in self-diagnostic function to detect system
errors. The self test is initiated each time the scanner is turned on.
During the test, the READY LED is flashing. At the end of the test, if no
error occurs, the READY LED is steadily on.

2-10
Figure 2-8 Cable connection
SCSI Cable
Connector
Power
Cable
SCSI Port
To PC SCSI
Port
To Power Outlet
Power Switch
SCSI Device B

2-11
2.6 INSTALLATION OF THE SCSI CARD
2.6.1 PC USERS
2.6.1.1 ADAPTEC SCSI CARD
Hardware Installation
1. Turn off your computer.
2. Plug the SCSI card in an available slot of your computer. Be
sure to screw it firmly.
3. Turn on your computer.
Software Installation
Windows 3.1
If your scanner comes with an Adaptec AVA-1505Ae, then the installation
of the SCSI card driver will be complete during the installation of the
scanner driver.
Windows 95/Windows 98/Windows NT4.0
Windows 95/98 has embedded driver support for your host adapter.
When you start Windows 95/98, the host adapter is detected and the
appropriate driver is automatically installed.

2-12
Windows NT 4.0
1. Press Start>Setting>Control Panel. And choose “SCSI Adapter”
from the Control Panel menu. The “SCSI Adapter” dialog box is
displayed. Choose Driver.
2. Choose “Add” and “Select manufacturer and SCSI adapter”.
3. Select “Adaptec” as the manufacturer and “AIC-6X60 ISA Single
Chip SCSI Controller” as the adapter and then Confirm.
4. Follow the on-screen instruction to complete the installation.
5. Restart your Windows NT 4.0.
2.6.1.2 OTHER SCSI CARDS
If you purchase your SCSI card separately from the scanner, then please
follow the installation instruction provided by your SCSI card supplier.
2.6.2 MAC USER
The Mac system already has SCSI controller built in. Connect the
system, therefore,set a different SCSI ID for each SCSI device.