SMC Networks Barricade SMC7004ABR User manual

Barricade™
Broadband Router
10/100 Mbps Broadband Router
◆ Instant Internet Sharing
◆ Firewall Security
◆ Simultaneous Web access for up to 253 PCs
◆ Built-in 10/100 Mbps switch
◆ Integrated print server
◆ Works with PCs or Macs
Quick Installation Guide
SMC7004AB
R
SMC7008AB
R

Table of Contents
Congratulations on your purchase of the SMC Barricade™ Broadband Router.................. 1
Hardware Setup ............................................................................................................................ 2
Configuring Your Computer........................................................................................................... 3
Configuring Your Computer with Windows 95/98/ME ............................................................. 3
Configuring Your Computer with Windows 2000 ..................................................................... 8
Configuring Your Computer with Windows NT 4.0................................................................ 13
Configuring Your Macintosh Computer................................................................................... 17
Configuring Your Barricade...................................................................................................... 21
Configuring Your Barricade for a Dynamic IP Address .......................................................... 24
Configuring Your Barricade for a Static IP Address................................................................ 26
Configuring Your Barricade for PPPoE ................................................................................... 28
Configuring Your Barricade for Dialup on Demand ................................................................ 30
Configuring Your Computer for the Barricade Print Server ................................................ 31
Configuring Your Computer for the Barricade Print Server for Windows 95/98/NT/ME/2000
.................................................................................................................................................. 31
Configuring Your Computer for the Barricade Print Server ................................................ 33
Configuring Your Computer for the Barricade Print Server for Windows 95/98/NT/ME/2000
.................................................................................................................................................. 33
Configure the Network Printer in Unix Systems ...................................................................... 35

Page 1
Congratulations on your purchase of the SMC Barricade™ Broadband Router.
The SMC Barricade is a Broadband Router designed to share Internet Access, provide security,
and to network multiple devices for a variety of users. The Barricade’s simple installation setup
can be used by the least experienced of users, while providing networking professionals with
easy to configure advanced features. Please read the User Guide for advanced features of this
product.
Thank you for purchasing an SMC product. We know you will enjoy the many features of the
SMC Barricade.
This Package Contains
• One SMC Barricade
• One Power Adapter
• This Quick Installation Guide
• One Installation CD
• One Category 5 Fast Ethernet Cable
Confirm That You Meet Installation Requirements
Before proceeding with the installation of your Barricade, please be sure you have the following:
• A computer with an Ethernet network card installed.
• Your Windows CD, if your computer is running Windows 95, 98, or ME
• An Internet connection through a cable or DSL modem or an external dial-up or ISDN
modem.
• An additional Ethernet network cable.
• A Web browser such as Internet Explorer or Netscape.

Page 2
Hardware Setup
SMC7004ABR – Front Panel
SMC7008ABR – Front Panel
1. Connecting Computers: Connect computers directly to the Barricade on ports 1-4/8 on the
front panel. If you have more than 4/8 computers to plug in, connect a hub or a switch (using
its uplink port) and connect additional computers to that device.
2. Connecting a Cable Modem or DSL Modem: Connect your Cable or DSL modem to the
WAN port on the rear panel.
3. Connecting a Dial-up Modem: If you use an external dial-up modem or ISDN modem,
connect it to the COM port on the rear panel.
4. Connecting a Printer: If you have a printer that you want to share between computers,
connect it to the Printer port using a standard parallel printer cable.
5. Power: Plug the power cord into the power jack.
SMC7004ABR – Rear Panel
SMC7008ABR – Rear Panel

Page 3
Indicator LEDs
The front panel of the Barricade provides indicator LEDs (Light Emitting Diodes) for easy
monitoring. The following table defines the function of each LED.
LED Condition Status
Power
(green) On Barricade is receiving power.
On The WAN port has established a valid network
connection.
WAN
(green) Flashing The WAN port is transmitting or receiving data.
On The indicated LAN port has established a valid network
connection.
Link/Act
(green) Flashing The indicated LAN port is transmitting or receiving data.
On The indicated LAN port is operating at 100Mbps.
10/100
(amber) Off The indicated LAN port is operating at 10Mbps.
On The indicated LAN port is operating in full-duplex mode.
FDX/COL
(SMC7008ABR) Flashing A collision occured on the indicated LAN port.
Configuring Your Computer
This Quick Installation Guide provides configuration instructions for Windows 95, 98, ME, NT
4.0, and 2000 and for Macintosh OS 7.x. Please be sure that you are following the proper
instruction set for your operating system.
• Configuring Your Computer with Windows 95/98/ME begins on this page.
• Configuring Your Computer with Windows 2000 begins on page 8.
• Configuring Your Computer with Windows NT 4.0 begins on page 12.
• Configuring Your Macintosh Computer begins on page 17.
Configuring Your Computer with Windows 95/98/ME
You may find that the instructions here do not exactly match your version of Windows. This is
because these steps and screenshots were created from Windows 98. Windows 95 and Windows
Millennium Edition are very similar, but not identical, to Windows 98.
Step 1. Configure TCP/IP Settings
After you have completed the hardware setup by connecting your devices, you need to configure
your computer to connect to your Barricade. You need to determine how your ISP issues your IP
address. Many ISPs issue these numbers automatically using a networking technology known as
Dynamic Host Control Protocol, or DHCP. Other ISPs will specify your IP address and
associated numbers, which you must enter manually. This is also known as a static IP address.
How your ISP assigns your IP address determines how you will configure your computer.

Page 4
Here is what to do:
1. From the Windows desktop, click the “Start” button. Choose
“Settings,” then click “Control Panel.”
2. From “Control Panel,” double-click the
“Network” icon.
3. In the “Network” window, under the “Configuration” tab,
double-click the “TCP/IP” entry that is listed with your
network card.

Page 5
4. Select the “IP Address” tab.
If “Obtain an IP address automatically” is already selected, your
computer is already configured for DHCP. Click “Cancel” to
close each window, and skip to Step 2 “Disable HTTP Proxy.”
5. Locate your IP address and Subnet Mask. Record them in the
spaces provided below.
6. Click the “Gateway” tab and record the numbers listed under
“Installed gateways.”
7. Click the “DNS Configuration” tab. Locate the DNS servers
listed under “DNS Server Search Order.” Record the listed
addresses.
8. After writing down your settings, check to make sure you have
recorded them correctly. Click the “IP Address” tab and then
click “Obtain an IP address automatically.” Click OK.
9. Windows may need your Windows 95/98/ME CD to copy
some files. After it finishes copying, it will then prompt
you to restart your system. Click “Yes” and your computer
will shut down and restart.

Page 6
TCP/IP Configuration Setting
IP Address ____.____.____.____
Subnet Mask ____.____.____.____
Primary DNS Server ____.____.____.____
Secondary DNS Server ____.____.____.____
Default Gateway ____.____.____.____
Step 2. Disable HTTP Proxy
You will need to verify that the “HTTP Proxy” feature of your Web browser is disabled. This is
so that your Web browser will be able to view the configuration pages inside your Barricade.
The following steps are for Internet Explorer and for Netscape. Determine which browser you
use and follow the appropriate steps.
Internet Explorer
1. Open Internet Explorer and click the stop button. Click
“Tools,” then “Internet Options.”
2. In the “Internet Options” window click the “Connections”
tab. Next, click the “LAN Settings…” button.
3. Clear all the checkboxes.
4. Click “OK,” and then click “OK” again to close the “Internet
Options” window.