Smeg DWAI152XT User manual

INSTRUCTION MANUAL
GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS
DWAI152XT SEMI-INTEGRATED DISHWASHER

Contents
1. Safety and operating instructions 2
2. Installationandhook-up 5
3. Descriptionof the controls 9
4. Operatinginstructions 20
5. Cleaningandmaintenance 35
6. Troubleshooting 39
Thank you for choosingoneof ourproducts.
You are advised to read this manual carefully; it contains all the
information you need aboutthe right conditions for the proper, safe use
of your dishwasher.
The individual sections are laid out to provide you with a step-by-
step guide to all your appliance's functions; the texts are easy to
understand and are complete with detailed illustrations.
Recommendations are given for the correct use of the baskets,
spray arms, containers, filters, washing programs, and for
operating the
controls.
Following the cleaning instructions provided here will keep
your dishwasher's performance at peak levels in the long term.
This user-friendly manual will provide answers to all your questions
about use of the dishwasher.
INSTALLATION INSTRUCTIONS: these are intended for the qualified
technician who must carry out the installation, hook-up and testing
of the appliance.
USER INSTRUCTIONS:these consistof recommendations for using the
appliance, a description of its controls and of the correct cleaning
and maintenance procedures.
1

Safety instructions
1. Safety and operating instructions
THIS MANUAL FORMS AN INTEGRAL PART OF THE APPLIANCE: IT MUST
ALWAYS BE KEPT INTACT TOGETHER WITH THE DISHWASHER. BEFORE
USING THE APPLIANCE, CAREFULLY READ ALL THE
I NSTRUCTIONS CONTAINED IN THIS MANUAL.
INSTALLATION MUST BE PERFORMED BY A QUALIFIED TECHNICIAN, IN
COMPLIANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS
INTENDED TO BE USED IN HOUSEHOLD AND SIMILAR APPLICATIONS
SUCH AS:
-STAFF KITCHEN AREAS IN SHOPS, OFFICES AND OTHER
WORKING
ENVIRONMENTS;
-FARM HOUSES;
-BY CLIENTS IN HOTELS, MOTELS AND OTHER RESIDENTIAL TYPE ENVIRONMENTS;
-BED AND BREAKFAST TYPE ENVIRONMENTS
IT COMPLIES WITH THE EEC DIRECTIVES 73/23, 89/336 (INCLUDING 92/31
AND 93/68) CURRENTLY IN FORCE, INCLUDING THE PREVENTION AND
ELIMINATION OF RADIO FREQUENCY INTERFERENCE.
THE APPLIANCE IS DESIGNED FOR THE FOLLOWING PURPOSE: WASHING
AND DRYING OF DISHES; ANY OTHER USE SHALL BE CONSIDERED
IMPROPER. THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR
USES OTHER THAN THOSE DESCRIBED ABOVE.
THE NAME PLATE FEATURING THE TECHNICAL DATA, SERIAL NUMBER
AND MARKINGS IS VISIBLY POSITIONED ON THE INNER EDGE OF
THE DOOR. THE NAME PLATE ON THE INNER EDGE OF THE DOOR
MUST NEVER BE REMOVED.
DO NOT LEAVE THE DISCARDED PACKAGING MATERIALS UNSUPERVISED
WITHIN THE HOME. SEPARATE THE VARIOUS MATERIALS WHICH
MAKE UP THE PACKAGING AND TAKE THEM TO THE NEAREST SORTED
WASTE COLLECTION CENTRE.
THE APPLIANCE MUST BE PROVIDED WITH AN EARTH CONNECTION
IN ACCORDANCE WITH THE ELECTRICAL SAFETY REGULATIONS IN
FORCE. THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR
DAMAGE TO PERSONS OR PROPERTY RESULTING FROM THE FAILURE
TO EARTH THE APPLIANCE OR FROM A DEFECTIVE EARTH CONNECTION.
IF THE APPLIANCE IS INSTALLED ON A CARPETED OR COVERED FLOOR,
ENSURE THAT THE OPENINGS ON ITS UNDERSIDE ARE NOT
OBSTRUCTED.
ALWAYS SWITCH OFF THE DISHWASHER AFTER EACH USE TO
AVOID WASTING ELECTRICITY.
WARNING: DISHWASHER DETERGENTS
ARE ASTRONGLY ALKALINE.
THEY CAN BE EXTREMELY DANGEROUS IF SWALLOWED.
AVOID CONTACT WITH SKIN AND EYES AND KEEP CHILDREN AWAY
FROM THE DISHWASHER WHEN THE DOOR IS OPEN.
2

Safety instructions
CHECK THAT THE DETERGENT RECEPTACLE IS EMPTY
AFTER COMPLETION OF THE WASHCYCLE.
OBSOLETE APPLIANCES MUST BE RENDERED UNUSABLE. CUT OFF THE
MAINS POWER CORD AFTER UNPLUGGING I T FROM THE WALL OUTLET,
AND MAKE SAFE ANY COMPONENTS WHICH MIGHT BE DANGEROUS FOR
CHILDREN (LOCKS, DOORS, ETC.).
THIS APPLIANCE IS MARKED ACCORDING TO THE EUROPEAN DIRECTIVE
2002/96/EC ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT
(WEEE).
BY ENSURING THIS PRODUCT IS DISPOSED OF CORRECTLY, YOU WILL
HELP PREVENT POTENTIAL NEGATIVE CONSEQUENCES FOR THE
ENVIRONMENT AND HUMAN HEALTH, WHICH COULD OTHERWISE BE
CAUSED BY INAPPROPRIATE WASTEHANDLING OF THIS PRODUCT.
THE SYMBOL ON THE PRODUCT, OR ON THE DOCUMENTS
ACCOMPANYING THE PRODUCT, INDICATES THAT THIS APPLIANCE MAY
NOT BE TREATED AS HOUSEHOLD WASTE. INSTEAD IT SHALL
BE HANDED OVER TO THE APPLICABLE COLLECTION POINT FOR
THE RECYCLING OF ELECTRICAL ANDELECTRONIC EQUIPMENT.
DISPOSAL MUST BE CARRIED OUT IN ACCORDANCE WITH
LOCAL ENVIRONMENTAL REGULATIONS FOR WASTE DISPOSAL. FOR
MORE
DETAILED INFORMATION ABOUT TREATMENT, RECOVERY AND
RECYCLING OF THIS PRODUCT, PLEASE CONTACT YOUR LOCAL
CITY OFFICE, YOUR HOUSEHOLD WASTE DISPOSAL SERVICE OR THE
SHOP
WHERE YOUPURCHASED THE PRODUCT.
IN THE EVENT OF A FAULT, DISCONNECT THE DISHWASHER FROM
THE ELECTRICAL POWER SUPPLY ANDSHUT OFF THE WATER TAP.
DO NOT USE APPLIANCES WHICH HAVE BEEN DAMAGED
DURING TRANSIT! IF IN DOUBT, CONSULT YOUR DEALER.
THE APPLIANCE MUST BE INSTALLED AND CONNECTED IN ACCORDANCE
WITH THE INSTRUCTIONS PROVIDED BY THE MANUFACTURER OR BY
A
QUALIFIED TECHNICIAN.
THIS DISHWASHER MUST BE USED BY ADULTS.
USE BY PERSONS WITH REDUCED MENTAL AND/OR
PHYSICAL CAPABILITIES IS ONLY PERMITTED UNDER THE
SUPERVISION OF A
PERSON RESPONSIBLE FOR THEIR SAFETY. KEEP CHILDREN AWAY
FROM DETERGENTS AND PACKAGING MATERIALS (PLASTIC BAGS,
POLYSTYRENE, ETC.), ANDNEVER ALLOW THEM TO APPROACH OR PLAY
WITH THE DISHWASHER, SINCE IT MIGHT CONTAIN DETERGENT
RESIDUES CAPABLE OF CAUSING PERMANENT DAMAGE TO THE
EYES, MOUTH AND THROAT, AND EVEN LEADING TO
SUFFOCATION. THE
APPLIANCE IS NOT INTENDED FOR USE BY YOUNG CHILDREN OR INFIRM
PERSONS WITHOUT SUPERVISION.
DO NOT INTRODUCE SOLVENTS SUCH AS ALCOHOL OR
TURPENTINE WHICH MAY CAUSE ANEXPLOSION.
DO NOT LOADDISHES THAT ARE SOILED WITH ASH, WAX ORPAINTS.

3

Safety instructions
LEANING OR SITTING ON THE DISHWASHER DOOR WHEN OPEN
MAY CAUSETHE APPLIANCE TO OVERTURN, PUTING PEOPLE AT RISK.
NEVER LEAVE THE DISHWASHER DOOR OPEN; PEOPLE MIGHT TRIP
OVER IT.
DO NOT DRINK THE WATER RESIDUES WHICH MAY BE PRESENT INSIDE
THE DISHES OR DISHWASHER AT THE END OF THE WASHING PROGRAM
ANDBEFORE THE DRYING CYCLE.
KNIVES OR OTHER SHARP-ENDED COOKING
UTENSILS MUST BE PLACED
IN THE CUTLERY BASKET BLADE-DOWN, OR LAID HORIZONTAL IN
THE TOP BASKET. TAKE CARE NOT TO CUT YOURSELF AND ENSURE
THAT THEY DO NOT PROJECT FROM THE BASKET.
AQUASTOP MODELS
THE AQUASTOP DEVICE PREVENTS FLOODING IN THE EVENT OF A
WATER LEAK. WHEN THE AQUASTOP DEVICE IS TRIPPED, CALL IN A
QUALIFIED TECHNICIAN TO IDENTIFY AND REPAIR THE FAULT.
IN MODELS EQUIPPED WITH THE AQUSTOP DEVICE, THERE IS A
SOLENOID VALVE INSIDE THE WATER INTAKE HOSE. DO NOT CUT
THE
HOSE AND DO NOT ALLOW THE SOLENOID VALVE TO DROP INTO
WATER. IN THE EVENT OF DAMAGE TO THE WATER INTAKE HOSE,
DISCONNECT THE APPLIANCE FROM THE ELECTRICAL POWER SUPPLY
AND FROM THE WATER SUPPLY.
IMMEDIATELY AFTER INSTALLING THE DISHWASHER, PERFORM A QUICK
TEST OF THE APPLIANCE FOLLOWING THE INSTRUCTIONS BELOW. IF
THE DISHWASHER FAILS TO OPERATE CORRECTLY, DISCONNECT IT
FROM THE ELECTRICAL POWER SUPPLY AND CALL THE
NEAREST TECHNICAL SERVICE CENTRE. DO NOT ATTEM PT TO
REPA I R THE APPLIANCE.
THE DISHWASHER MEETS ALL THE REQUIREMENTS SET OUT BY THE
REGULATIONS IN FORCE CONCERNING SAFETY AND ELECTRICAL
EQUIPMENT. ANY TECHNICAL CHECKS SHOULD BE CONDUCTED
EXCLUSIVELY BY A TRAINED AND AUTHORISED TECHNICIAN: REPAIRS
CARRIED OUT BY UNAUTHOR I SED PERSONS WILL INVALIDATE THE
WARRANTY, AS WELL AS POSING A POTENTIAL HAZARD TO THE USER.
The manufacturer declines all responsibility for damage to persons or property
resulting from failure to observe the above precautions, from tampering
with even a single component of the appliance, or from the use of non
original spare parts.
4

Installation instructions
2. Installation and hook-up
Removethe polystyrene basketretainers.
Position the appliance in the desired place of installation. The back
or sides of the dishwasher may be placed up against walls or
other
furniture units. If the dishwasher is installed near a heat source, fit the
special insulating panel to prevent overheating and malfunction of
the appliance. To ensure stability, install integrated or built-
underdishwashers only under continuous worktops, and screw them
to the adjacent units. To facilitate the installation procedure, the
intake and drain hoses can be positioned in any direction; make sure
that the hoses are not kinked, crushed or pulled too tightly. Make sure
to tighten the locking ring-nut once the pipes have been placed in
the direction required. A hole at least 8 cm in diameter is required to
allow the power supplycable and pipes to pass.
Level the appliance on the floor using its adjustable feet. This operation
is essential for ensuring correct operation of the dishwasher.
Building-in a dishwasher underneath a ceramic hob is absolutely
forbidden.
A dishwasher can be built-in underneath a conventional hob provided
there is no breakin the kitchenworktop,andthe dishwasherandhob are
installed and secured correctly, so that no hazards are generated.
When installing the dishwasher in a compartment next to one or
more other appliances, it is essential to comply with all the
recommendations provided by the appliance’s manufacturer (minimum
distances, installation procedures, etc.).
For free-standingmodelsonly:
- Installing a hob on top of a free-standing dishwasher is
absolutelyforbidden.
- If the appliance is not built-inandisthereforeaccessibleononside, the
doorhinge areamustbecoveredforsafetyreasons(injuryhazard).The
covering fixtures are available as an accessory from specialist dealers
or theAfter-SalesService.
- To build in the dishwasher, the special kit must be purchased from
authoriseddealersorthe After-SalesService.
Some models are equipped with only one adjustable foot at the
rear, which can be adjusted by turning the screwon the lower front part
of the appliance.
5

Installation instructions
2.1 Water supply connection
Preventing the risk of clogging or damage: if the water pipe is newor
has not beenusedfor a long time,before connecting to the water supply
check that the water is clear and free of impurities,to prevent damage to
the appliance.
The dishwasher must always be connected to the water system
with new hoses; old or used hoses must never be reused.
CONNECTING TO THE WATER SUPPLY
Connect the intake hose to a cold water supply with
¾” gas thread, inserting the filter A supplied with
the dishwasher. Take care to screw the hose firmly
into place with your hands and then complete
by tightening about ¼ of a turn with pliers.
In dishwashers equipped with the ACQUASTOP
device, the filters is already fitted inside the threaded
ring.
The dishwasher can also be connected to a hot water supply not
exceeding 60°C. Supplying the appliance with hot water cuts down the
washing time by approximately 20 minutes, but slightly reduces its
effectiveness.Makethe connection tothedomestichotwatersupplyusing
the same procedure described for connecting to the cold water supply.
DRAIN CONNECTION
Insert the dishwasher’s drain hose
into a drainpipehaving a diameter
of at least 4 cm, or alternatively,
place it inside the kitchen sink
using the plastic support provided,
taking care not to crush or
excessively bend the hose. It is
important to prevent the hose from
coming loose and falling. For this
purpose, the plastic support is
equipped with a hole for tying it to
the wall or water tap.
The free end should be positioned at a height of between 30 and 100
cm, and should never be submerged in water. If a horizontal drain
extension hose is used (for a maximum of3 m)the drain hose can be
placed at a maximum height of 85 cm from the ground.
6

Installation instructions
2.2 Electrical connection and precautions
CHECK THAT THE VOLTAGE AND THE FREQUENCY OF THE MAINS MATCH
THE RATINGS ON THE NAME PLATE OF THE APPLIANCE POSITIONED ON
THE INNER EDGE OF THE DOOR.
THE PLUG ON THE SUPPLY CORD AND THE CORRESPONDING
SOCKET OUTLET MUST BE OF THE SAME TYPE AND MEET THE
REGULATIONS IN FORCE.
THE PLUG MUST BE ACCESSIBLE AFTER INSTALLATION.
NEVER DISCONNECT THE PLUG BY PULLING ON THE POWER SUPPLY
LEAD.
IN THE EVENT OF DAMAGE TO THE SUPPLY CORD, HAVE IT REPLACED
BY THE MANUFACTURER OR AN AUTHORIZED TECHNICAL
SERVICE CENTRE.
DO NOT USE ADAPTORS OR SHUNT CONNECTIONS IN ORDER TO AVOID
THE POSSIBILITY OF OVERHEATING OR BURNING.
IF THE APPLIANCE IS PROVIDED WITH A PLUGLESS SUPPLY CORD:
IT IS NECESSARY TO INSTALL IN THE FIXED WIRING AN ALL-
POLE DISCONNECTION DEVICE HAVING A GAP BETWEEN CONTACTS
OF AT LEAST 3.5MM. AFTER INSTALLATION THE DISCONNECTION
DEVICE HAS TO BE EASY TO REACH.
THE CONNECTION TO THE MAINS MUST BE
CARRIED OUT BY A
QUALIFIED TECHNICIAN IN ACCORDANCE TO THE SCHEME
SHOWN BELOW AND THE REGULATIONS IN FORCE.
L = brown
N = blue
= yellow-green
In the event of damage to the supply cord, have it replaced by the
manufacturer or an Authorized Technical Service Centre in order to
avoid any risk.
7

Installation instructions
FOR GREAT BRITAIN ONLY:
THIS APPLIANCEMUST BE EARTHED.
Fuse replacement
If the mains lead of this appliance is fitted
with a BS 1363A 13amp fused plug, to
change a fuse in this type of plug use
an A.S.T.A. approved fuse to BS 1362
type and proceed as follows:
1. Remove the fuse cover Aand fuse B.
2. Fit replacement 13A fuse into fuse
cover.
3. Refit both into plug.
The fuse cover must be refitted when changing a fuse and ifthe fuse
cover is lost the plug must not be used until a correct replacement is
fitted.
Correctreplacement areidentified by the colour insert or the colour
embossed in words on the base of the plug.
Replacementfusecoversare availablefrom yourlocal electrical store.
8

User
instructions
3. Description of the controls
3.1 Front panel
All the dishwashercontrols are grouped on the front panel.
1
ON/OFF BUTTON
2
SELECTION PROGRAM BUTTONS (P1…P5)
3
OPTION SELECTION BUTTON
4
CONFIRM OPTIONS BUTTON
5
DELAY PROGRAM BUTTON
6
START/PAUSE BUTTON
7
POWER ON LIGHT
8
PROGRAMS INDICATOR LIGHTS
9
INFORMATION DISPLAY
10
RECESSED DOOR HANDLE
N.B.: symbols and styling are guideline and may vary depending on
the modelorversion of the dishwasherpurchased.
9

User
instructions
3.2 Information display
The dishwasher is equipped with a practical DISPLAY which
provides informationontheprogrammeddishwasherfunctions.
A
4-FIGURE DISPLAY
B
RINSE AID WARNING LIGHT (onsomemodelsonly)
C
SALT WARNING LIGHT (operates onlyon somemodels)
D
START/PAUSE BUTTON
E
OPTIONS LIGHT
PROGRAMS TABLE
The manual contains the programs table for several models. To find the
tablefor your dishwasher,comparetheprogram symbols at the top of the
table with those on your control panel.
10

User
instructions
PROGRAMS TABLE
PROGRAMME
NUMBER
& SYMBOL
LOAD CROCKERY AND
CUTLERY
PROGRAM
PROGRESS
DURAT I ON
CONSUMPTION
M I NUTE S
(1)
WATER
LITRES
POWER
KWh (1)
1SOAK
Pansand dishesawaiting
completionof theload
Coldprewash
15'
3,5
0,02
2 NORMAL
ECO (*)
Crockery and cutlery
normallysoiled
Cold prewash
Wash at 49°C
Rinse at 41°C
Dry
142’
11,6
0,66
3 ECO
Disheswith normaldirt,
even with dried-on
residues
Cold prewash
Wash at 55°C
Cold rinse
Rinse at 70°C
Dry
100’
11
1,3
4 AUTO 60-70
Pansand disheswith
normal dirt, even with
dried-on residues
The prewash and the washing temperature are decided
automatically depending on the type and amount of dirt.
The program ends with a final drying phase.
5 SUPER
Very dirty pans and
dishes, even with dried-on
residues.
Hot prewash
Wash at 70°C
Cold rinse (2)
Rinse at 70°C
Dry
135'
15,5
1,60
* Reference program as per AS/NZS 2007.
Only run the soak program withpartial loads.
(1) The cycle duration and power consumption may vary according to the water and
room temperatures, and the type and amount of dishes.
(2) 1 or 2 cold rinses depending on the model.
If the dishwasher door is open or not properly closed, the washing cycle
will not start.
11

User
instructions
QUICK TIME PROGRAMS (seerelevant section forexplanationof functioning modes)
The ENERSAVE option cannot be used with soak, ultra clean or quick time
programs.
PROGRAMME
NUMBER E
SYMBOL
LOAD CROCKERY AND
CUTLERY
PROGRAM
PROGRESS
DURATION
CONSUMPTION
M I NUTI
(1)
WATER
LITRES
POWER
KWh (1)
6 RAPID 27’
+
Dishes with light dirt,
washed immediately after
use
Wash at 38°C
Rinse at 50°C
27'
6,5
0,70
7 ECO
QUICK
+
Disheswith normal dirt,
washed immediately after
use.
Cold prewash
Wash at 60°C
Cold rinse
Rinse at 70°C
80’
12,5
1,25
8 INTENSIVE
QUICK
+
Disheswith normal dirt,
washed immediately after
use
Coldprewash
Wash at 70°C
Cold rinse
Rinse at 70°C
95'
12,5
1,35
9 STRONG
and FAST
+
Mixed disheswith normal
dirt without dried-on
residues.
Wash at 65°C
Cold rinse
Rinse at 70°C
55'
9,5
1,35
(1) The cycle duration and power consumption may vary according to the water and
room temperatures, and the type and amount of dishes.
If the dishwasher door is open or not properly closed, the washing cycle
will not start.
12

User
instructions
3.3 Washing programs
The dishwasher is equipped with a control panel and an INFORMATION
DISPLAY from which it is possible to carry out all the power switch-on,
switch-off and programming operations.
Before starting a washing program make sure that:
• The water supply tap is open.
• The correct amount of detergent has been added to the
dispenser.
• The basketshavebeen correctly loaded.
• The spray arms are able to rotate freely and
without obstruction.
• The dishwasher door is securely closed.
LIGHTING
Pressing the ON/OFF button will start the dishwasher and will lit up the
dishwasher pilot light. After approximately3 second from this operation
the DISPLAY will be turned on with a visualization that will depend upon
the state of the dishwasher.
PROGRAMMING
All the programmingoperations are possible onlywith closed door. With
open door, on the DISPLAY will appear - - :- -.
SELECTION PROGRAM
The program selection is possible
throughthe relative buttons.
By pressingtherelativebutton of desiredprogram (see table)itwill lid up
the relative pilot light to confirm that the operation did occurred on the
DISPLAY will appear a program duration forecasting (“h.mm”).
13

User
instructions
START PROGRAM
At this point, in order to start the machine, itis onlyenough to press the
START/PAUSE (6) for some seconds until the symbol START/PAUSE
(D) start to flash andconfirmation“beep” is heard. From this momentthe
cycle duration on the DISPLAY (9) starts to decrease.
This phase, that updates itself during the cycle, is “indicative” since it is
influenced by the washing conditions such as dishwasher type and
quantity, entry temperature etc. For this reason it is normal to see
the updating during a program (increment and decrease of
minutes) specially in the passage from one phase to the other (for
example, from washing to rinse).
END PROGRAM
The end of the program is indicated bya short signal acoustic and from
the “End” visual notification on DISPLAY. By pressing one of the
buttons, the “End”visual signal will vanish from the display and
the dishwasher is readyto continue a new cycle.
INTERRUPTING APROGRAM
In orderto interrupt a runningprogram itis necessary:
• to press the START/PAUSE for some seconds until when
the symbol START/PAUSE remains lit on the display
(confirmation beep). At this point,it is possible to start the cycle
again, otherwise:
•
TO CHANGE A PROGRAM
To change the runningprogram itis necessary:
• to interrupt the running program (see “INTERRUPTING A PROGRAM”);
• selectthe newprogram;
• to press again the START/PAUSE button to make start the new
program.
14

User
instructions
STOPPING A PROGRAM
To cancel a program which is running:
• Interrupt the program (see"INTERRUPTINGA PROGRAM")
• Press the START/PAUSE button and hold it down; the
display will show "P0" and the dishwasher will immediately
switch to the end of the cycle and drain the tank (during
this process, the "START/PAUSE symbol will flash). When
the drain procedure ends, the end of cycle "End"
message appears on the display.
In case that the door is opened during the operation, to the next
door closing it is going to be necessary to start the program as
shown in paragraph “STARTING THE PROGRAM”. The program will
resume from the point in which it was interrupted.
In case that the tub temperature is higher than 50°C the program
will start about 60 seconds later.
15

User
instructions
PROGRAM DELAY
The PROGRAM DELAY button can be pressed to delaythe start of the
washing program byfrom 1 to 12/24 hours depending on the model. This
optionallowsthedishwashertobe operatedatthe timeof dayof the user's
choice. The first time the PROGRAM DELAY buttonis pressed the
option light comes on and 1:h appears on the DISPLAY. The button can
then be pressed again, to set the delay required ( 2:h, 3:h , …etc.). If no
buttonispressedforafew seconds,theDISPLAY shows thetimeleft(time
remaining) to the end of the selected program (e.g. 5:40, duration of the
washingcycle+ program delay).Whenthe userconfirms theprogramstart
(read the relative section) a prewash will be carried out, after which the
PROGRAM DELAY setwillbegin,andthetimeremaining on the DISPLAY
willgraduallybe counteddown.At the end of the delayset, the optionlight
goes out andthe washing cycle starts.
N.B.: It is not possible to select the PROGRAM DELAY option once the
cycle has begun.
Chosen the delay, proceed with the program start, press the
button START/PAUSE for same seconds until the START/PAUSE
symbol start to flash.
The machine will perform adishpre-washing,andwhenfinish, the “delay
program” will enter in function as itwas first set.
In case you want to put to zero the “delay program” within the running
program it is necessary:
• to press the START/PAUSE button for some seconds until
the START/PAUSE (D) symbol remainliduponthe display;
• to press the DELAY PROGRAM moretimes untilthe resetof the
delayprogram (START/PAUSE symbolshutoff);
• to press the START/PAUSE buttonto makestartthe program.
N.B.: It is notpossible to select the “delay program”when the program
have alreadybegan.
16

User
instructions
OPTIONS (availableinall programs exceptthe soakprogram)
The options arecontrolledby the OPTION
SELECTION button .
Press the button to access the procedure,
confirmed by flashing of one of the OPTIONS
lights (E).
N.B.: The PROGRAM DELAY light only comes onwhenthespecific
PROGRAM DELAY button is pressed.
Press theSELECTOPTIONS button againtodisplaythenextoption.
To confirmanoption,presstheCONFIRM OPTION button (thelight
stops flashingandremainson).Thisoperationcanbecarriedoutforoneor
alloftheoptionsavailable.Todeactivateanoptionwhichhasalreadybeen
confirmed,presstheOPTIONSELECTION button until theOPTION
LIGHT requiredflashes,andpresstheCONFIRM OPTION button . The
lightstopsflashingandgoesout.
All optionsexcept"FlexiTabs"aredisabledattheendofthewash cycle.
QUICK TIME PROGRAMS
Select this option together with any washing program (except the soak
program)toSHORTEN the cycle. To activate this option,press button
(light comes on) after selecting the program required.
Theoptionis automaticallydeactivated atthe end of the program.
17