Smiley Daisy Pyramid User manual

Never use other acids, enzymes or detergents, as
this may risk creation of poisonous gas or cause
malfunctioning.
The cover has an inner cover which can also be
removed for easy cleaning.
•Pull the grip to release.
•After cleaning the inner cover, replace by holding
the grip and pressing down inner cover to water
tank.
PRECAUTIONS
Avoid unit malfunction by taking note of the
following:
•Do not fill over 80ml (“MAX”) at any time.
•Do not switch on the power when the tank is
empty.
•Do not touch the Ultrasonic vibration plate.
•Clean regularly as per Maintenance instructions to
avoid malfunctioning
•Always unplug from the power supply before
maintenance.
•For hygiene purposes, pour away remaining water
from “DRAIN SIDE” of the tank, and wipe with a
clean dry cloth after each use.
•Essential oils can stain. In case of oil spillages on
other surfaces, wipe away with a soft cloth.
•Only use the measuring cup provided to add water
to the tank. Never fill directly from the tap.
•Do not let mist blow directly onto furniture,
clothing, walls, etc.
•Keep away from direct sunshine, heat sources, air
conditioners, or fans.
•Always keep on a stable flat surface. Do not place
on carpet or any unstable area.
•Keep away from electronic equipment, such as TV
and audio equipment.
•Do not tip the product. This may cause water to
enter the mechanism and cause malfunctioning.
•Do not use for more than 3 hours any time.
TROUBLESHOOTING
Please refer to the table below in case product is not working
properly.
Problem
Possible Cause
Solution
Will not
switch
on or off
•Is there enough
water in the tank?
•Is the power cord
connected properly?
•Add water to the tank
•Disconnect, check the cables
and reconnect carefully.
No mist
or
abnormal
mist
•Not enough water?
•Too much water?
•Dirt on the
ultrasonic plate?
•Cover and inner
cover are not
installed properly?
•Dirt on the air intake
on the underside of
the base?
•Add correct amount of water in
the tank.
•Tank must never be filled over
80ml of water
•Please refer to maintenance
instructions.
•Remove and re-install
correctly, so vapors can be
released freely.
•Clean the air intake of any dust
restricted airflow will affect
mist.
Water
leakage
from
product
•Cover and inner
cover not installed
properly?
• Has the unit tipped
over?
•Low temperature or
high humidity?
•Remove and reinstall correctly,
so vapors can be released
freely.
•Follow accidental leakage
instructions.
•Under these conditions, the
mist may condense quickly into
water droplets.
Smiley Daisy provides free 180 days product
replacement warranty for this product, which starts
from the date of your purchase. Please keep your
sales receipt handy in a safe place.
SPECIFICATIONS
Dimensions
Approx 5.9” x 5.9” x 5.2”
Weight (excluding
adaptor)
Approx 9.2 oz.
Power Input/Output
AC 100-240V 50.60HZ / DC 12V 1A
Adapter Certification
UL, CE, RoHS
Length of Cord
Approx. 67”
Electric consumption
Approx. 9W
Water tank capacity
80ML
LED light
6 Bulbs
Materials
Upper parts PP, lower base ABS
Method of mist
production
Ultrasonic vibration at approx 2.4MHz
WARRANTY
AROMA DIFFUSER
User Manual
Visit our website for
tips, tricks, coupons and
more!
www.smileydaisy.com
PO Box 2252
Livingston, NJ 07039 U.S.A.
201-455-7770 M-F 9am-5pm
(EST)
[e-mail]

The Aroma Diffuser is a one-of-kind product that
uses the power of ultrasonic waves to vaporize
water and essential oils in its tank. This process
creates fragrant, cool, and dry mist.
OPERATION
1. Place the product in an upside position and
remove the upper cover. (Fig 1)
2. Plug the AC adaptor to the DC jack found on the
base of the product's main body using the cable
guide. (Fig 2)
3. Use the measuring cup provided carefully. Add
water into the tank. Never fill your tank with water
directly from the tap. (Fig 3)
•Pay attention to the filled water level. Do not
exceed the max line on the water tank.
•Never use water with high temperature; this may
cause product malfunctioning.
•Never fill tank with water during operation.
4. Drop essential oils into the tank vertically. The
dosage is about 2-3 drops (about 0.1-0.15ml) per
100ml of water.
5. Replace upper cover and ready for use. Note:
Always cover the main body of the product before
every use. (Fig 5)
6. Plug the AC adaptor into an electrical supply
socket.
7. If you press the MIST button found on the main
body, the mist function will turn on. From here you
can easily set up the timer function. Each time you
press the button, the timer will set for an operation
time as follows, 60 minutes, 120 minutes, 180
minutes, ON and OFF. (Fig 6)
•If the timer is set to ON, the unit will run as
continuous mist mode until no water.
•If there is little water in the water tank, the power
supply will automatically turn off.
•If the timer mode is off, the LED light will also be
off.
8. If you press the LIGHT button, you can toggle
between the ON/OFF states of the LED light options.
Each time you press the button the color and
brightness changes. To choose a specific color, press
the light button again. Press and hold Light button for
2 seconds to turn off the light function. (Fig 6)
9. If you will not use the product for a long time, drain
out the water from the tank and dry completely. Store
the product in a dry and cool area. If you wish to use
it again, use a gentle detergent to clean the tank.
(Please see maintenance)
ATTENTION
•The amount and intensity of mist produce may
vary depending on the water type, temperature, air
currents, and humidity. This is not unusual and
should not be considered a defect.
•In the event that there is not enough water inside
the tank, pressing the MIST button will cause the
unit to beep three times. You must add adequate
water in order for the unit to start working again.
•This product is only compatible with 100%
natural essential oil. Oils containing chemical
fragrances, spice, or other impurities will cause
malfunctioning. Take note to add only 2-3 drops
of essential oil per 100ml of water. Too much oil
will clog the unit and cause malfunctioning. If
you plan to use a new type of essential oil, clean
the unit following maintenance instructions.
ACCIDENTAL LEAKAGE
In the event that the unit is knocked or tipped
over during operation, follow these steps to avoid
malfunctioning.
•Unplug the unit and remove upper cover.
•Pour out any remaining water out of the tank.
•Shake the unit gently and drain any water inside
the mechanism. Allow 24 hours for unit to dry
before reusing.
MAINTENANCE
After every 5-6 times of use or every 2-3 days
clean the product as follows.
•Unplug the unit from the main power supply and
remove upper cover.
•Pour out any remaining water from the
“DRAIN SIDE” of the tank.
•Unplug power cord from the base of the unit.
•Place 1 tablespoon of citric acid (sour salt) in the
water tank, then add 70ml of warm water.
•Leave for 5 minutes and drain the solution
through the “DRAIN SIDE” of the tank.
•Wipe the unit dry using a soft cloth. Avoid the
ultrasonic vibration plate area.
•The ultrasonic vibration plate area can be
cleaned using a cotton bud (Q-tips).