SmoothTalker BTEUX415 User manual

2
2) Placement: Place the outside antenna in the middle of the vehicle roof.
If the vehicle has a sunroof please place the antenna on the roof towards the back
window. Place the coupling holder in desired location.
Connect the amplier as shown in Fig. 2 on Pg.1.
Important: Use only the power supply included with the amplier. Connecting any
other power supply at any time will result in damage to the amplier and will void
the warranty. Do not turn on the power switch until ALL cables have been
screwed or plugged into the amplier or you can cause damage to the amplier.
1) This Direct Connect M2M amplier is designed to be placed between the Mobile
device and it’s outside antenna. Make all connections as in Fig. 1 & 2 on Pg.1 or
Fig. 3 on Pg. 4.
Installation
Smoothtalker approved accessories must be used with this amplier to maintain
warranty.
Approved Equipment List
ANTENNA CABLES
ACX100, ACX900
CBXmaXfe10,20,30,40,50,60
CBNmaNfe10,20,30,40,50,60
CBGmaGfe 10,20,30,40,50,60
ANTENNAS
SEM2, 11, 14, series
SEM2M, 11M, 14M, series
SEM2LGM, 11LGM, 14LGM, 26LGM series
SEM2LGML 11LGML, 14LGML, 26LGML series
SEM2TH, 11TH, 14TH, 26TH series
SEM2THL, 11THL, 14THL, 26THL series
SEMTHMM series
SEMTHPB series
SEMRP1X , SEMRP1XL
SRBL series
SEMD1 series
SEMDA2 series
SEMO series
SEMDP1 series
SEMDY series
SEMDYD series
5
800MHz 900MHz 1800MHz 2100MHz
Stealth M2M X4 Parts Included
(Power supply and antenna may vary depending on Kit purchased)
Smoothtalker.com
STEALTH M2M X4 4G LTE
Direct Connect Machine to Machine
Signal amplifier Extreme Power
Smoothtalker.com
User Manual
Mobile
Signal Amplifier
DIRECT CONNECT
RX/TX
15dB 4 BAND
MULTI BAND 15dB
GSM,HSPA,CDMA,LTE, LTE A
Machine to Machine
Extreme Power
2G, 3G, 3G+, 4G, 4G+
4 BAND
15dB
MULTI BAND
Gain
15 dB
3
Operating temp
-30 C TO + 85 C
Dimensions Weight 0.249 kg
L 11.6 x W 6.4 x H 3.2 (cm)
Model Series
BTEUX415
SPECIFICATIONS 2G, 3G, 3G+, 4G, 4G+, GSM, HSPA, CDMA, LTE, LTE A
Frequencies MHz
Max Power-TX: Watts EIRP
BTEUX415
stealth
tech
®
POWER
SUPPLY 100-240V AC/DC
Band 20
Band 8
Band 3
Band 1
1800MHz
2100MHz
800MHz
900MHz
Max Power RX: mW
0.0032mW
Declaration of Conformity
In accordance with EU Directives and Regulations
Mobile Communications Inc.
230 Earl Stewart Dr. Aurora, ON. Canada L4G6V8,
as the manufacturer hereby declares under our sole responsibility that the, Product(s):
Mobile Signal Enhancer, Model name/s: Smoothtalker :
BTEUX430 Mobile CX4, BTEUX415 Stealth M2M X4
Is/are in conformity with the requirements of the RE Directive 2014/53/EU:
The radio equipment meets the following essential requirements
Article 3.1 a): Health and Safety Conform
Article 3.1 b): Electromagnetic Compatibility Conform
Article 3.2: Eective and Ecient Use of Radio Spectrum Conform
Radio EN 301 908-1 V11.1.1, EN 301 908-15 V11.1.2, EN 303 609 V12.5.1
EN 301 908-11 V11.1.2
Article 3.2
EMC EN 301 489-1 V2.2.0, EN 301 489-50 V2.2.0
Article 3.1(b)
Safety EN 62368-1: 2014
Article 3.1(a)
Health RF Exposure EN 62311: 2008
Article 3.1(a)
An EU Type Examination Certicate for this Product was issued in accordance with Annex III
(Module B) of the 2014/53/EU Radio Equipment Directive by Bay Area Compliance
Laboratories Corp. (2014/53/EU Radio Equipment Directive Notied Body Identication
Number 1313)
This product has been tested and certied CE, RoHS.
stealth
tech
®
Automatic power
control protects the
Mobile Network
RE Directive 2014/53/EU
Certified Compliant
For Inquires please contact Us
[e-mail]

34
LED Lights Explanation and Troubleshooting
The LED lights on the amplier face plate indicate the operating gain state of
the amplier.
The Green and Orange lights indicate the gain status in each operating band
When Both Green and Orange LED's are“SOLID ON” it means that the amplier
is operating normally with full gain (No Automatic Gain Reduction)
When one or both of the LEDS are ashing (Per the chart on Pg. 6) it indicates
that the gain has been automatically reduced due to either:
A) High receive (RX) outside signal level (when very close to cell tower)
B) Loop Oscillation, caused when the inside antenna is located too close to the
outside antenna
Each ash indicates 3dB of gain reduction also known as gain attenuation.
For example: three ashes equals 9dB of attenuation.
Green LED indicates loop oscillation status. When ashing it means reduction of
gain. To improve coverage you need to spread the distance between the inside
and outside antennas. If you spread them far enough away, the Green LED will
become SOLID ON which indicates the amplier is working at its max gain.
Orange LED indicates RX (outside signal) status.
There are 4 Orange LED lights: 800 Mhz , 900 Mhz ,1800 Mhz, 2100 Mhz.
LED ON state indicates that the RX (Receive Signal) function of the band is
functioning normally. LED OFF state indicates that the band is shut down.
When Orange LED is ashing it indicates reduced gain also known as
attenuation of gain. You cannot prevent this condition. It means that the outside
signal is very strong and the amplier has reduced it's gain in order to protect the
closest cell tower. If the cell tower which is close is the one you are using, then
you can ignore the gain reduction and you will still get enough signal strength
to cover your area. In this case this is the normal operating process.
Operational description:
This devices comprise with International NPS (Network Protection
Standard): NPS and other compliance/safeguard features for AGC and
anti-oscillation have been implemented. NPS and other compliance/
safeguard features are defaulted to be“On” (in operation). NPS and other
compliance/safeguard features can not be eld recongured, disabled or
removed. This amplier is not user programmable, does not need ne
tuning or adjustment.
If the close cell tower is not the one you are using, then you can try to relocate
your outside antenna away from this cell tower and face it or point it to the cell
tower you are using in order to get more gain.
If you need help pls contact [e-mail] and we will help
you determine your cell tower location and get you setup.
Mobile Cradle Direct Connect
220 V Power Type
Mobile Tracking Direct Connect
CLA 12V Socket Type
Fig. 1 Fig. 2
Band Frequency
RX High Power Attenuation
Oscillation Attenuation
Hp Att
Osc Att
Understanding the LED Indicators
LED Lights Indicate Gain Status
ON ON
ON
SLOW FLASHING
SOLID ONSOLID ON
SOLID ON
SOLID ONSLOW FLASHING
FAST FLASHING
OFF
ON/
ORANGE LED
RX High Power
GREEN LED
Oscillation
Attenuation (Att)
Orange Solid ON = Full Gain & Green Solid ON = Full Gain
Orange Solid ON & Green Slow Flashing = Oscillation Att
Orange O & Green Fast Flashing = Oscillation Shutdown
Orange Slow Flashing & Green Solid ON = RX High Power Att
Each ash indicates 3dB of gain reduction also known as gain attenuation.
For example: three ashes equals 9dB of attenuation.
No Flashing = Full Gain
Each Flash = up to 3dB gain reduction
Each Flash = up to 3dB gain reduction
Fast Flashing = amplier shutdown (pls troubleshoot)
Orange LED
Green LED
Band 1 2100MHz
Band 3 1800MHz
Band 8 900MHz
Band 20 800MHz
Outside Antenna
Outside Antenna
amplier
amplier
Modem
Modem
In 2001 SmoothTalker produced the rst digital mobile Mobile signal
amplier in North America with FCC and Industry Canada approval.
We continue to lead with the most powerful and intelligent ampliers
in the world. Our dynamic adaptive proprietary algorithms make
them totally network friendly. We call it STEALTH TECH technology.
6
Typical Installation Stealth M2M X4 (Fig. 3 )
Outside Antenna
Modem
amplier
1
Contents
Modem
Mobile amplifier
Mobile Modem or
other M2M device
(Not included)
NOTE: Only one of the outside antennas is included in this kit (check model) All kits include necessary brackets
and co-axial cables for assembly. It is normal for the amplier to be quite warm while the phone is in use state.
To comply Smoothtalker warranty, this amplier must only be operated with cables, antennas, and coupling
devices that have been approved for use with this equipment (Pg. 5).
Outside antenna options
100-240 volt
Power Supply
SEM2MX SEM11MX SEM14MX SEMDP1
Smoothtalker®
Stealth M2M X4 4G LTE
Mobile
Signal amplifier 4 BAND
MULTI BAND 15dB
Direct Connect
RX/TX
2G, 3G, 3G+, 4G, 4G+
GSM, HSPA, CDMA, LTE, LTE A
Hp Att
Osc Att
DC 6V Only Outside Antenna
Inside Antenna
Band 20 800MHz
Band 8 900MHz
Band 3 1800MHz
Band 1 2100MHz