SnapPad EQ Compact User manual
RV SNAPPAD
EQ COMPACT
INSTALLATION INSTRUCTIONS
1-866-923-9538 | INFO@RVSNAPPAD.COM | RVSNAPPAD.COM 4J | EQ7SP4
Very Important Notes:
It is critical that you install the correct SnapPad on the proper foot. Please triple check prior to installing
your SnapPads. Permanent damage could result from trying to install on the wrong landing foot,
resulting in your warranty being voided. Your EQ Compact’s are designed to work with 7” octagonal jack
feet that are commonly found on Equalizer® leveling systems.
*Trademark is owned by mark owner. SnapPad and its goods are not ailiated with or endorsed by the
mark owner.
Congratulations on
joining the SnapPad family!
EQ COMPACT INSTALLATION INSTRUCTIONS RV SNAPPAD 01
SnapPad EQ Compact
Installation Instructions
Motorhome Detailed Installation Instructions
EQ COMPACT INSTALLATION INSTRUCTIONS RV SNAPPAD 02
• SnapPad installation is best performed on a hard, level or near level surface – preferably a hard surface (concrete or asphalt). Wheel chocks can be placed in front of and
behind the RV wheels for additional safety.
• Be sure to thoroughly clean and dry your landing feet prior installing your SnapPads.
• Spread a small bead of concentrated dish soap around the lip of the SnapPad and metal landing foot to aid installation. Do NOT use any petroleum based lubricant,
such as WD-40®, as it may negatively react with the binder in your SnapPads.
• Install one SnapPad at a time and use the manual jack operation if possible. Refer to your owners manual for instructions.
• Most jacks are 18” - 24” under your RV. You might need to use a tool such as a broomstick to align your SnapPads, if necessary.
• Install one at a time. It’s important that you align your SnapPads correctly to ensure they install properly and are not damaged during the
installation process. ALL 4 SIDES MUST BE ALIGNED WITH THE LIP OF THE PAD. Do NOT install any of the corners to align with the slots
on the lip. These slots are for drainage and help with removal should you ever need to take your SnapPads o.
INSTALLATION TIME: 3 - 6 MINUTES PER PAD.
• Once aligned, begin lowering your jack. Keep an eye on the landing foot as it extends. Stop extending when the foot is about 2 to 3 inches from the SnapPad. Double check
to make sure it is centered and the 4 sides line up with the SnapPad, re-align if necessary and then continue extending the landing gear to complete installation.
KEEP YOUR FINGERS AND ANY FOREIGN OBJECTS CLEAR WHEN LOWERING THE JACK INTO PLACE.
• You should hear a distinctive “snap” as the lip engages. Visually conrm the lip is fully engaged around the perimeter of the landing foot.
• If your lip hasn’t fully engaged, raise your jack and place a shim (small piece of wood no thicker than 1/4”) under the side that hasn’t engaged. Lower your jack again until
that side snaps into place.
• Wipe o any excess soap and repeat the installation process, in sequence, on your remaining jacks.
SnapPad EQ Compact
Info & Statistics
• Dimensions: 9.00” wide x 2.00” thick.
• Once installed they add about an inch to your jack thickness.
• 3.00 pounds per pad.
• You’re helping our environment! SnapPads are made from American recycled tires. That
means SnapPads are not only durable and versatile but environmentally friendly too.
• Will work on any type of surface, level or unlevel, including: asphalt, concrete, grass, mud,
sand, resin, ice, and snow.
• Scientically tested to maintain integrity at over 120°F down to -40°F and remain attached at
over 50x the force of gravity.
• Generally, it takes 1,300 pounds of vertical pressure to install your SnapPads. This ensures no
matter how far o the beaten path you venture, your SnapPads will be there with you.
• Proudly made in the USA.
• It’s best (and easiest) to install your SnapPads one at a time on a level, hard surface.
• Each leveling system will have it’s own manual operation function. Please refer to your owners manual for specic directions.
• Grab a helper! It’s safer, faster, and more eicient with two people.
• Use your phone or another person to relay the information between the installer and the person working the controls.
• Install each SnapPad individually and visually conrm the reinforced lip has engaged on the complete diameter. It is critical your SnapPad has been installed fully and
correctly.
• Standing water? No problem! Your SnapPad EQ Compact pads have built-in drainage channels.
• Your SnapPads come with a handy bolt-access hole in the center. You can use this to remove the jack with the SnapPad still attached if needed.
• Installation is easier in warm weather (50°F or more).
While not required, we recommend double protecting your jacks by covering the landing feet with a rubberized protectant such as Flex Seal®. Make sure to cover your jack
cylinders prior to applying and coat the bottom of your landing feet as well. Do this prior to installing your SnapPads and allow the protectant to cure for 24 hours. Do not
spray your SnapPads with the sealant (it will not adhere to the rubber).
HELPFUL HINTS & TRICKS FOR EQ COMPACT
EQ COMPACT INSTALLATION INSTRUCTIONS RV SNAPPAD 03
Origen RV Accessories LTD oers a 2-year manufacturer’s warranty on both performance and defects in material and workmanship. Should your product fail within a 2-year
time frame, Origen RV Accessories LTD will replace your pad free of charge. Warranty coverage does not extend to Acts of god, misuse of product, improper installation, and
damage from external events like accidents.
WARRANTY INFORMATION
• You must register your product warranty rst in order to be able to le a claim later on, if necessary. For more information, visit
https://rvsnappad.com/pages/general-warranty
• Origen RV Accessories LTD will replace any defective products within the acceptable 2-year window, starting from the purchase date.
• To submit your warranty claim please visit https://rvsnappad.com/pages/le-a-claim.
• Proof of purchase is required for any warranty redemption on your pads.
• If you need to return your UNUSED pads within 30 days of purchase please contact our Customer Service Agents at info@rvsnappad.com
• Be advised the product must be shipped back to Origen RV Accessories LTD at your cost, meaning you pay the shipping charges for returning any pads.
• Once shipped, email your tracking number to [email protected]om for conrmation and then your refund will be issued.
Please note: If your SnapPads were purchased from an RV Dealer, Amazon, or other online source we encourage you to contact them for your replacement/refund.
CONDITIONS
• SnapPads are an aermarket RV accessory, and as such, it is the responsibility of the RV owner to ensure they are an appropriate and safe addition to their RV.
• Each RV has unique design considerations. It is the responsibility of the RV owner to conrm their SnapPads have adequate clearance for any moving parts and will not
hinder the functionality of any other system.
• Origen RV Accessories LTD shall not be liable for any special, incidental, indirect or consequential damages whatsoever (including but not limited to, labor, installation,
charges, damage to associated equipment, RV, trailer, towing or following vehicle) arising from the use or inability to use or install the product.
• Use extreme caution when installing and using SnapPad. Origen RV Accessories LTD is not responsible or liable in any way for any indirect or direct injury sustained
during installation or future use of the product.
• Installing SnapPad products on non-compatible leveling systems will result in the voiding of the warranty and can lead to product failure, property damage, or injury.
Origen is not responsible for any issues arising from the use of our products on non-compatible systems.
• SnapPads are designed to be installed once. Do not remove and re-install as this will also void your warranty. *Unless performed by an authorized dealer. Picture
conrmation may be necessary to conrm successful reinstallation.
EQ COMPACT DISCLAIMERS
EQ COMPACT INSTALLATION INSTRUCTIONS RV SNAPPAD 04
Table of contents
