Snapper 216518B User manual

Parts Manual fo
r
Revision 1,
21" STEEL DEC
K
SERIES 18
COPYRIGHT
©
2005
McDonough, GA, 30253 U.S.A.
TP 400-5047-1-WB-N
9/9/2005 Manual No. 7006139
SNAPPER PRODUCTS, INC.
ALL RIGHTS RESERVED.
WALK BEHIND MOWERS
PUSH MODELS PROPELLED
MODELS
216518B EP217018BV
ERP217018BV
P216018KWV
P216518B
P217018BV
P217018BV
E
RP216018KWV
RP217018BV
RP217018BVE

Table Of Content
s
TP 400-5047-1-WB-N
Manual No. 700613921" STEEL DECK
SERIES 18 3
PAGE GROUP
4HANDLES & CONTROLS
8CUTTING DECK, BLADES
12 FRONT WHEEL BRACKET
14 REAR WHEEL BRACKETS, LATCHES
16 FRONT WHEELS
18 REAR WHEELS
20 DRIVE SYSTEM SELF-PROPELLED
24 TRANSMISSION (DIFFERENTIAL)
26 THROTTLE CONTROLS/ENGINE SPECS
28 SIDE CHUTE ADAPTER
30 ACCESSORY GRASS BAG
32 ELECTRIC START COMPONENTS
34 DECALS
36 SNAPPERIZER ACCESSORY
38 THATCHERIZER ASSEMBLY
40 RECYCLING KITS ACCESSORY

HANDLES & CONTROLS
TP 400-5047-1-WB-N
Manual No. 7006139 21" STEEL DECK
SERIES 18
4

HANDLES & CONTROLS
Footnotes:
TP 400-5047-1-WB-N
Manual No. 700613921" STEEL DECK
SERIES 18 5
Part No Descri
p
tionItem Qt
y
Note
1 7074411 1 HANDLE, Upper All
2 7074156 1 HANDLE, Middle All
3 7033985 1 HANDLE, Lower LH (Adjustable) All
4 7033986 1 HANDLE, Lower RH (Adjustable) All
5 7074418 1 BAIL, OPC Control All
6 7034872 1 CLIP, Zone Control All
7 7034608 1 *CABLE, Zone Control (52-63/64” Long)
7 7078078 1 CABLE, Zone Control (50-31/64” Long) P217018BVE & RP217018BVE
7 7074141 1 CABLE, Zone Control (56-5/16” Long) P216018KWV & RP216018KWV
8 7074473 1 HANDLE, Clutch Self-Propelled Models
9 7028407 1 GRIP, International Symbol Self-Propelled Models
10 7034604 1 CABLE, Clutch Control (41-1/4” Long) Self-Propelled Models
11 7012121 1 COVER, Vinyl Self-Propelled Models
12 7012122 1 SPRING, Clutch- 21S Self-Propelled Models
13 7074003 1 BRACKET, Shift All
14 7024641 2 TIE, Wire, 1.29 long, black Self-Propelled Models
15 7073822 1 BRACKET, Bell Crank Self-Propelled Models
16 7013849 1 SPACER, .33 x .63 x .156 Self-Propelled Models
17 7073913 1 BELL CRANK Self-Propelled Models
18 7073826 1 CONTROL PANEL (w/o Ground Drive Slot) 216518B
18 7074140 1 **CONTROL PANEL (w/o Electrical Switch Hole)
18 7074469 1 CONTROL PANEL (w/Electrical Switch Hole) P217018BVE & RP217018BVE
19 7091200 4 SCREW, 1/4-20 x 1/2” Pan Head Self-Tap (Torx) All
20 7091130 1 WASHER, .33 x .88 x .09 Flat Self-Propelled Models
21 7091904 1 SCREW, 5/16-18 x 7/8” Hex Head Cap, GR 5 Self-Propelled Models
22 7090895 1 TEENUT, 5/16-18 Self-Propelled Models
23 7012114 1 BUSHING, Differential, .328 x .625 x .41 Self-Propelled Models
24 7090595 3 BOLT, 5/16-18 x 3/4” Hex Flange Lock GR 5 All
25 7091601 2 NUT, 5/16-18 Hex Flange Lock, GR 5 was 7090585 (All)
26 7091575 1 NUT, 5/16-18 Hex Center Lock was 7091067 (S-P Models)
27 7074113 1 LEVER, Shift Self-Propelled Models
28 7091606 1 NUT, 5/16-24 Hex Center Lock GR 5 was 7091074 (All)
29 7023813 1 CLIP, Wiring Harness All
30 7091740 4 SCREW, 5/16-18 x 1-7/8” Curved Head GR 2 was 7091189 (All)
31 7035744 4 KNOB, 5/16-18 Wing (Black) All
32 7079577 2 SCREW, 1/4-20 x 1-1/2 Hex Head Cap GR 5 All
33 7090053 3 WASHER, 1/4” Internal Tooth Lock was (All)
Note* used on 216518B, P216518B, P217018BV, RP217018BV, EP217018BV & ERP217018BV
Note** used on P217018BV, P216518B, P216018KWV, RP217018BV, RP216018KWV, EP217018BV & ERP217018BV
Note* See also Throttle Control Page
ref Decal Page

HANDLES & CONTROLS
TP 400-5047-1-WB-N
Manual No. 7006139 21" STEEL DECK
SERIES 18
6

HANDLES & CONTROLS
Footnotes:
TP 400-5047-1-WB-N
Manual No. 700613921" STEEL DECK
SERIES 18 7
Part No Descri
p
tionItem Qt
y
Note
34 7091576 3 NUT, 1/4-20 Hex was 7091100 (All)
35 7090505 1 SCREW, 1/4-20 x 2” Hex Head Cap, GR 5
36 7014343 2 BUSHING, .27 x .35 x .4 Flange Self-Propelled Models
37 7023792 1 PIN, 1/4 x 1-1/2” Self-Propelled Models
38 7091020 1 PUSH-NUT, 1/4” Self-Propelled Models
39 7015753 2 BALL JOINT, 1/4-28 Self-Propelled Models
40 7090095 4 NUT, 1/4-28 Hex Self-Propelled Models
41 7022458 1 FOAM GRIP, 15” long All
42 7091305 1 SCREW, 3/8-16 x 2” Hex Head Cap, GR 5 Self-Propelled Models
42 7091553 1 SCREW, 3/8-16 x 1-3/4” Hex Head Cap, GR 5 Push Models
43 7091585 1 NUT, 3/8-16 Hex Center Lock All
44 7090391 4 WASHER, 5/16” Internal Tooth Lock All
45 7031961 8 WASHER, 7/16” Flat Self-Propelled Models
46 7028465 2 WASHER, Nylon Self-Propelled Models
47 7074133 1 ROD, Speed Control (1/4-28 thread) Self-Propelled Models
48 7028488 1 GUIDE, Rope (1/4-20 thread) All
49 7076978 1 NUT, 1/4-28 Hex GR 5 or B All
50 7012080 2 CABLE-TIE, 7” Self-Propelled Models
51 7074460 1 *THROTTLE CONTROL, .48 x .61 Briggs models
51 7074138 1 *THROTTLE CONTROL, 6.0 KWV Kawasaki models
52 7075308 1 THROTTLE KNOB All
53 7075182 1 KNOB, Shift Self-Propelled Models
54 7026219 1 CLAMP, 7/8” Double Cable Self-Propelled Models
55 7091167 1 SCREW, #8-32 x 1/2” Cross Recess Filister Head Machine Self-Propelled Models
56 7091018 1 NUT, #8-32 Hex Self-Propelled Models
57 7032408 1 BELT GUIDE, Lower Self-Propelled Models
58 7028568 1 WASHER, Belleville Self-Propelled Models
59 7090053 4 WASHER, 1/4” Internal Tooth Lock Self-Propelled Models
60 7090188 1 WASHER, 3/8” Flat Self-Propelled Models
61 7034162 1 COTTER PIN, 5/16 Self Lock Self-Propelled Models
62 7029365 1 DECAL, Easy Walk All
63 7023153 1 CLAMP, Casing models with Briggs Engine
64 7023154 1 SCREW,#10-32 x 5/8” Self-Tap models with Briggs Engine
65 7090238 1 SCREW, 5/16-24 x 1” Hex Head Cap GR 5 All
Note* used on 216518B, P216518B, P217018BV, RP217018BV, EP217018BV & ERP217018BV
Note** used on P217018BV, P216518B, P216018KWV, RP217018BV, RP216018KWV, EP217018BV & ERP217018BV
Note* See also Throttle Control Page
ref Decal Page

CUTTING DECK, BLADES
TP 400-5047-1-WB-N
Manual No. 7006139 21" STEEL DECK
SERIES 18
8

CUTTING DECK, BLADES
Footnotes:
TP 400-5047-1-WB-N
Manual No. 700613921" STEEL DECK
SERIES 18 9
Part No Descri
p
tionItem Qt
y
Note
1 7057663 1 DECK, Mower (incl. painted “HV” Deck with Decals) Non-Recycler models
1 7072716 1 DECK, Mower, 21” Hi-Vac (HV) 216518B
1 7074949 1 DECK, Mower (Includes painted “Euro M” Deck with No Decals) RP217018BVE
1 7057884 1 * DECK, Mower, 21” Non-Adj Air (was 7041857 or 7057784) Recycler models
2 7091601 10 NUT, 5/16-18 Hex Flange Lock, GR 5 was 7090585
3 7090731 3 BOLT, 5/16-18 x 1/2”, Short Neck Carriage, GR 5
4 7091169 1 BOLT, 5/16-18 x 1-1/8” Short Neck Carriage, GR 5
5 7090324 3 SCREW, 3/8-16 x 1” Self-Tapping engine mount bolts
6 7046780 2 PLUG, Hole, Polyethylene
7 7090534 1 SCREW, 5/16-18 x 1/2” Hex Head Cap, GR 5
8 7090702 1 BOLT, 5/16-18 x 2-1/4”, Hex Flange Lock
9 7013320 1 BUSHING, .388 x .625 x 1.62
10 7033863 1 COVER, Belt European models
11 7031961 3 WASHER, 7/16” Flat
12 7090167 1 SCREW, 3/8-24 x 2” Hex Head Cap, GR 5
13 7012063 2 WASHER, Cone
14A 7019795 1 BLADE, Cutter, 21” Air Lift (European) EP217018BV
14B 7026691 1 BLADE, Cutter (Standard Lift) Domestic Push & S.P.models
14C 7026407 1 BLADE, 21” Ninja (Quad Edge) Recycler models
15 7015626 1 HUB, Blade Drive 25mm I.D.
16 7091214 1 KEY, Woodruff #HP-506 Hi-Pro
17 7090201 1 SET SCREW, 5/16-18 x 5/16” Hex Socket
18 7015780 1 PULLEY, Engine (25mm I. D. x 2-1/8” O.D.)
19 7091122 6 SCREW, 1/4-20 x 1/2” Hex Flange Self-Tap (was 90539) EP217018BV & ERP217018BV
20 7041400 1 WELDMENT, Fender European models
21 7091508 2 BOLT, 5/16-18 x 3/4” Short Neck Carriage GR 5 was 7090001
22 7011791 1 RETAINER, 5/16” Bolt
23 7091601 3 NUT, 5/16-18 Hex Flange Lock, GR 5 was 7091070
-- 7060785 -- KIT, Air Lift (Incl. items 24 thru 27)
24 7032558 2 AIR LIFT
25 7090391 4 WASHER, 5/16” Internal Tooth Lock
26 7091297 4 NUT, 5/16-24 Hex, GR 5 was 7090223
27 7090228 4 SCREW, 5/16-24 x 21/32” Machine
28 7044770 3 SPACER, .06 Thick for blade hub
29 7074568 1 COVER, Belt
30 7046471 3 PLUG, 5/16” Square Hole Push Models
31 7045264 2 PLUG, 5/16” Round Hole qty. 3 on Push Models
Note* Same deck as 7074949 except w/o battery bracket holes.
Note* Purchase engine parts from engine manufacturer dealer.

CUTTING DECK, BLADES
TP 400-5047-1-WB-N
Manual No. 7006139 21" STEEL DECK
SERIES 18
10