Snapper 7800440 SPVH2265 User manual

Parts Manual fo
r
22" STEEL DECK REAR DISCHARG
E
VARIABLE SPEED WALK BEHIND MOWER
Revision: B 2/9/2010
Briggs & Stratton Yard Power Products Group
Manual No. 7006486
535 Macon Road
McDonough, GA, 30253 U.S.A.
800-935-2967
Descri
p
tionModel No.
780044
7
NSPVH2265
7800609 NSPVH22675
780044
0
SPVH2265
780060
6
SPVH22675
Not for
Reproduction

Not for
Reproduction

Table Of Contents
TP 400-5429-B-WB-N
22" STEEL DECK REAR DISCHARGE
3
Manual No. 7006486
PAGE GROUP
4 Handles and Controls
6 Deck Assembly
8 Engine, Blade & Grass Bag
10 Transmission (22")
12 Decals
Not for
Reproduction

Handles and Controls
Manual No. 7006486 22" STEEL DECK REAR DISCHARGE
4
Not for
Reproduction

Handles and Controls
Footnotes:
Manual No. 700648622" STEEL DECK REAR DISCHARGE
5
Part No Descri
p
tionItem Qty
1 7101068 1 PANEL, Upper Handle, Snapper 21 WBM
2 1960382 2 RIVET, Pop .250 Dia.
3 7100844A 1 BAIL, Pivot Handle
4 7300434A 1 HANDLE, Pivot
5 7023655 1 LEVER, Lock Handle
6 7300526A 1 HANDLE, Lock
7 7026257 1 WASHER, .531 x .781 Wave
8 1716654 1 BOLT, 5/16-18 Shoulder
9 7071921 1 RIVET, Plastic Snap
10 7091601 5 NUT, 5/16-18 Flange Lock, YZ
11 7090669 2 SCREW, 5/16-18 x 1-3/4” Hex Head Cap, GR 5
12 7300792A 1 BRACKET, Rotation Limit, RH
13 7300436A 1 BRACKET, Rotation Limit, LH
14 7900067 2 SCREW, 1/4-20 x .55 Torx Self-Tap
15 7300459A 2 HANDLE, Upper, Straight, 22”
16 7023649 2 WASHER, 5/16 Nylon
17 7028488 1 ROPE GUIDE, (1/4-20 thread)
18 7076978 1 NUT, 1/4-20 Hex Nyloc
19 7090361 1 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
20 7090951 4 NUT, 5/16-18 Large Head Center Lock, Black
21 7301013A 1 HANDLE, Lower
22 7091085 1 BOLT, #10-24 x 1/2” Flat Head Square Neck
23 7102666 1 CABLE, OPC, 22”, Pivot Handle
24 7102665 1 CABLE, Drive, 22”, Pivot Handle
25 7091290 1 NUT, #10-24 Hex Nyloc
26 7090505 2 SCREW, 1/4-20 x 2”, Hex Head Cap, GR 5
27 7090372 1 NUT, 1/4-20 Hex Center Lock
28 7035744 4 KNOB, 5/16-18 Wing (Black)
29 7090391 4 WASHER, 5/16” Internal Tooth Lock
30 7091189 2 BOLT, 5/16-18 x 2” Curved Head Square Neck, GR 2
31 7300669A 1 BRACKET, Lower Handle LH 22” WBM
32 7300668A 1 BRACKET, Lower Handle, RH 22” WBM
33 7091612 2 BOLT, 5/16-18 x 1-1/2” Round Head Square Neck
34 7091811 2 BOLT, 5/16-18 x 5/8” Hex Flange Lock, YZ
35 7091601 2 NUT, 5/16-18 Flange Lock, YZ
36 7024649 1 WIRE TIE, 11 Inch Standard Black Nylon
37 721768 2 CLIP, Cable, Double
Not for
Reproduction

Deck Assembly
Manual No. 7006486 22" STEEL DECK REAR DISCHARGE
6
Not for
Reproduction

Deck Assembly
Footnotes:
Manual No. 700648622" STEEL DECK REAR DISCHARGE
7
Part No Descri
p
tionItem Qty
1 7300400D 1 DECK, 22” Walk, 3-N-1
2 7900067 3 SCREW, 1/4-20 x 11/16” Pan Head Self-Tap (Torx) or 722848
3 7091020 4 PUSHNUT, 1/4”
4 7300855D 1 BRACKET, Chute
5 7300856D 1 PLATE, Mulch, 22” RB Scott's
6 722507 1 SPRING, Chute (Torsion)
7 7101067 1 ROD, Pivot (1/4” Dia. x 5.55”)
8 721682 1 COVER, Mulch, Plastic, Black
9 721681 1 SIDE CHUTE, Plastic, Black
10 7103347 1 GUARD, Rear
11 7091286 4 SCREW, #10-24 x 1/2” Hex Washer Self-Tap (Sems)
12 7091619 10 NUT, 3/8-16 Hex Flange Lock, YZ
13 7501055 1 ASSEMBLY, Height-Of-Cut, Left Rear, 22” WBM
14 7501056 1 ASSEMBLY, Height-Of-Cut, Right Rear, 22” WBM
15 7501058 1 ASSEMBLY, HOC, Left Front, 22” WBM, Propelled
16 7501057 1 ASSEMBLY, HOC, Right Front, 22” WBM, Propelled
17 7100633 4 GRIP, Height Latch
18 7500540 2 ASSEMBLY, Wheel & Bearing, 8 x 2 Idle, DW Tread incl. two 1-1/8” O.D. Flanged Ball Bearings
(p/n 7101380)
19 7500542 2 ASSEMBLY, Drive Wheel & Bearing, 8 x 2, DW Tread incl. two 1-1/8” O.D. Flanged Ball
Bearings (p/n 7101380)
20 722604 4 WASHER, 1” O.D. x .387 I.D. Flat
21 7091585 4 NUT, 3/8-16 Hex Center Lock, YZ
22 7101350 4 HUBCAP, Black
23 7300440D 1 BAFFLE, Front, 22” WBM
24 7101243 1 DOOR, 22” Rear
25 7101070 1 ROD, Pivot, Rear Door (1/4” Dia. X 17-1/2”)
26 7101461 1 SPRING, Torsion, Rear Door, 22” WBM
27 7300668A 1 BRACKET, Lower Handle, RH 22” WBM
28 7300669A 1 BRACKET, Lower Handle LH 22” WBM
29 7091811 2 BOLT, 5/16-18 x 5/8” Hex Flange Lock, YZ
30 7091601 3 NUT, 5/16-18 Flange Lock, YZ
31 7014341 4 RING, External Retaining (Waldes 5133-50)
32 7101207 2 GEAR, Pinion, 22” WBM, Front Wheel Drive
33 7101402 2 DUST SHIELD, Forward, 22” WBM
34 7900054 4 SCREW, 3/8-16 x 3/4” Hex Head Cap, GR 5, YZ
35 7100857 1 TRANSMISSION, Rocker 22” WBM, VS
36 7101270 2 DRIVE PIN, 22” WBM, Front Wheel Drive
37 7300854D 1 BAFFLE, Rear, 22” Deck
Not for
Reproduction

Engine, Blade & Grass Bag
Manual No. 7006486 22" STEEL DECK REAR DISCHARGE
8
Not for
Reproduction

Engine, Blade & Grass Bag
Footnotes:
Manual No. 700648622" STEEL DECK REAR DISCHARGE
9
Part No Descri
p
tionItem Qty
1 720351 1 BOLT, 3/8-16 NS x 2-1/2”
2 7101449 1 ASSEMBLY, Engine Spacer, 22” WBM, Self-Propelled includes 7101209 (spacer) & 7101448
(3) (bushings)
3 7101195 1 FRONT COVER, Deck, 22” Front Wheel Drive
4 7900018 2 SCREW, 4.8 x 1.59 x 13mm, Round Washer Head Hi-Lo (Torx)
5 7101302 2 SPACER, Belt Guide 22”
6 7101024 2 BELT GUIDE, Engine, 22”
7 7101451 2 SCREW, 3/8-16 x 3” Hex Washer Self-Tap
8 7100437 1 PULLEY, Engine
9 7092086 1 SET SCREW, 5/16-18 x 1/2” Hex Recess
10 7091214 1 KEY, #HP-506 HI-PRO
11 7100913 1 ** BELT, Drive (3L Section; 31.94” effective length)
12 7100740 1 BLADE HUB, 22” Deck, Self Propelled
13 7100851 1 BLADE, 22”, Walk Mower
14 721890 1 WASHER, .38” I.D. x 1.183 O.D. Bellville
15 720209 1 BOLT, 3/8-24 x 3-1/4” Hex Head, GR 8
16 7101230A 1 BAG FRAME, 22” WBM (weldment)
17 7102573 1 GRASS BAG, 22” Rear Discharge
18 7026421 1 GRIP, Rectangular (Black)
19 124T02-0650-B3 1 * ENGINE, B&S, 650 Ser, X-Spec used on 7800440
19 124L02-4650-F3 1 * ENGINE, B&S, 650 Ser, X-Spec used on 7800447
19 126T02-0675-B3 1 * ENGINE, B&S, 675 Ser, X-Spec used on 7800606
19 126L02-4675-F3 1 * ENGINE, B&S, 675 Ser, X-Spec used on 7800609
NOTE: * Purchase engine parts from engine manufacturer dealer.
Note: ** Part number appears on belt
Not for
Reproduction

Transmission (22")
Manual No. 7006486 22" STEEL DECK REAR DISCHARGE
10
Not for
Reproduction

Transmission (22")
Footnotes:
Manual No. 700648622" STEEL DECK REAR DISCHARGE
11
Part No Descri
p
tionItem Qty
1 7100857 1 TRANSMISSION, Rocker 22” WBM, VS
2 7900032 8 SCREW, 7mm x 1 x .550 AB Point
3 7100913 1 ** BELT, Drive (3L Section; 31.94” effective length)
4 7101009 1 BELT GUIDE, Transmission, 22” WBM
5 7900055 2 SCREW, #10-14 x 1/2” Hex Washer Self-Tap or 7091195 (SCREW, #16-16 x 3/4” Pan Head
Self-Tap, Combo)
Note: ** Part number appears on belt
Not for
Reproduction

Decals
Manual No. 7006486 22" STEEL DECK REAR DISCHARGE
12
Not for
Reproduction

Decals
Footnotes:
Manual No. 700648622" STEEL DECK REAR DISCHARGE
13
Part No Descri
p
tionItem Qty
1 7101538 1 DECAL, Front Cover, 22” Snapper, FWD
2 7102862 1 DECAL, Pivot-N-Go
3 7102153 1 DECAL, Briggs Engine, 675 Series
4 7102697 1 DECAL, Pivot Handle, Snapper
5 7101547 1 DECAL, Neutral Lock
6 7029782 1 DECAL, OPC Bail International Symbol
7 7102152 1 DECAL, Briggs Engine, 650 Series
8 7102151 1 DECAL, Briggs Engine, 675 Series
9 7102746 1 DECAL, Spark Arrestor
10 7101394 1 DECAL, Warning, Rear Discharge Door
11 7013010 1 DECAL, Danger, Cut Finger
Not for
Reproduction

Not for
Reproduction

in/lbs
ft/lbs
3
Torque Specification Chart
FOR STANDARD METRIC MACHINE HARDWARE (Tolerance ± 20%)
Property
Class
Class 8.8 Class 10.9 Class 12.9
Size Of
Hardware Nm. Nm. Nm. Nm.
M3 1.28
2.90
5.75
9.9
16.5
24
48
83
132
200
275
390
530
375
995
1350
1830
2360
3050
13.44 1.80
4.10
8.10
14
23
34
67
117
185
285
390
550
745
960
1400
1900
2580
3310
4290
19.2 22.92
2.15
M4
30.72 43.44 52.56 4.95
M5
60.96 5.97 7.15
16.5
9.7
M6 7.3 10.3 12.1
M7 12.1 16.9 19.9 27
M8 17.7 25 29 40
M10 35 50 59 81
M12 61 86.2 103 140
M14 101 136 162 220
M16 147 210 250 340
M18 202 287 346 470
M20 290 405 486 660
M22 390 559 656 890
M24 497 708 840 1140
M27 733 1032 1239 1680
M30 995 1401 1681 2280
M33 1349 1902 2278 3090
M36 1740 2441
3798
2935 3980
M39 2249 3163
Torque Specification Chart
FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%)
Hardware
Grade
SAE Grade 2 SAE Grade 5 SAE Grade 8
Size Of
in/lbs
ft/lbs
in/lbs
ft/lbs
in/lbs
ft/lbs
in/lbs in/lbs
Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm.
8-32 19 2.1 30 3.4 41 4.6
8-36
20 2.3 31 3.5 43 4.9
10-24
27 3.1 43 4.9 60 6.8
10-32
31 3.5 49 5.5 68 7.7
1/4-20
66 7.6 810.9 12 16.3
1/4-28
76 8.6 10 13.6 14 19.0
5/16-18 11 15.0 17 23.1 25 34.0
5/16-24 12 16.3 19 25.8 29 34.0
3/8-16 20 27.2 30 40.8 45 61.2
3/8-24 23 31.3 35 47.6 50 68.0
7/16-14 30 40.8 50 68.0 70 95.2
7/16-20 35 47.6 55 74.8 80 108.8
1/2-13 50 68.0 75 102.0 110 149.6
1/2-20 55 74.8 90 122.4 120 163.2
9/16-12 65 88.4 110 149.6 150 204.0
9/16-18 75 102.0 120 163.2 170 231.2
5/8-11 90 122.4 150 204.0 220 299.2
5/8-18 100 136 180 244.8 240 326.4
3/4-10 160 217.6 260 353.6 386 525.0
3/4-16 180 244.8 300 408.0 420 571.2
7/8-9 140 190.4 400 544.0 600 816.0
7/8-14 155 210.8 440 598.4 660 897.6
1-8 220 299.2 580 788.8 900 1,244.0
1-12 240 326.4 640 870.4 1,000 1,360.0
Hex Head Capscrew
Hex Nut
Lockwasher
Washer
Carriage Bolt
NOTES
1. These torque values are to be used for all hardware
excluding: locknuts, self-tapping screws, thread forming
screws, sheet metal screws and socket head setscrews.
2. Recommended seating torque values for locknuts:
a. for prevailing torque locknuts - use 65% of grade 5
torques.
b. for flange whizlock nuts and screws - use 135% of
grade 5 torques.
3. Unless otherwise noted on assembly drawings, all torque
values must meet this specification.
Hardware Identification & Torque Specifications
Common Hardware Types
No
Marks
The guides and ruler furnished below are designed to
help you select the appropriate hardware.
8.8 10.9 12.9
Class 5.6
5.6
5150
13.44 1.28
5.88
26.4 2.50
44.64 4.3
5.2
7.1
7.7
10.5
15
21
988
1340
759
1030
590
800
435
590
320
435
217
295
169
230
126
171
89
121
64
88
42
58
26
36
.56
Thread
Diameter (mm)
Screw, 1/2- 16 x 2
Body
Diameter
Diameter
Inside
Diameter (in)
Nut, 1/2-16
0
1/4 3/4
1/2
21
1/4 3/4
1/2 1/4 3/4 1/2 1/4 3/4 1/2
4
90 10070 80 50 60 30 40 01020
Thread
Diameter (mm)
Nut, M8 Screw, M8- 1.25 x 25
Distance between
threads (mm)
Body
Length (in)
Body
Length (mm)
3/8” Bolt or Nut
Wrench—9/16”
5/16” Bolt or Nut
Wrench—1/2”
1/4” Bolt or Nut
Wrench—7/16”
1/2” Bolt or Nut
Wrench—3/4”
7/16” Bolt or Nut
Wrench (Bolt)—5/8”
Wrench (Nut)—11/16”
in/lbs
Threads
per inch
Threads
per inch
Body Length
Body
When a washer or nut is identified as 1/2” (M8), this is
the
Nominal size , meaning the inside diameter is 1/2 inch
(8mm metric thread diameter); if a second number is present
it represents the
threads per inch (distance between threads).
When bolt or capscrew is identified as 1/2 - 16 x 2” (M8 - 1.25 x 50 ),
this means the
Nominal size , or body diameter is 1/2 inch (8mm
metric thread diameter), the second number,16, represents the
threads per inch, (1.25 thread diameter). The final number is the
body length of the bolt or screw, 2 inches (50mm).
Standard Hardware Sizing
M6 Bolt or Nut
Wrench—10mm
M8 Bolt or Nut
Wrench—13mm
M10 Bolt or Nut
Wrench—17mm
M12 Bolt or Nut
Wrench—19mm
M14 Bolt or Nut
Wrench—22 mm
Wrench & Fastener Size Guide
Not for
Reproduction

Parts Manual fo
r
22" STEEL DECK REAR DISCHARGE
IT IS THE POLICY OF BRIGGS & STRATTON CORP TO IMPROVE ITS
PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO.
WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD
IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY
OBLIGATION TO MAKE SUCH CHANGES ON PRODUCTS
VARIABLE SPEED WALK BEHIND MOWE
Revision: B 2/9/2010
Manual No. 7006486
Cop
y
ri
g
ht
©
2010
Milwaukee, WI USA. All Rights Reserved
Bri
gg
s & Stratton Corporation
www.sna
pp
er.com
Briggs & Stratton Yard Power Products Group
535 Macon Road
McDonough, GA, 30253 U.S.A.
800-935-2967
Not for
Reproduction