Snapper FB13250BS User manual

Parts Manual fo
r
Revision 1,
FIELD & BRUSH MOWER
SERIES 0
COPYRIGHT
©
2005
McDonough, GA, 30253 U.S.A.
TP 400-5009-1-CW-N
8/30/2005 Manual No. 7006933
SNAPPER PRODUCTS, INC.
ALL RIGHTS RESERVED.
MODEL
FB13250B
S
FB13250B
V
FB15250KW

Table Of Content
s
TP 400-5009-1-CW-N
Manual No. 7006933FIELD & BRUSH MOWER
SERIES 0 3
PAGE GROUP
4HANDLE PARTS GROUP
8ENGINE DECK GROUP
12 MOWER DECK PARTS GROUP
14 DECALS GROUP
16 ELECTRICAL & MISC. GROUP
18 WIRING HARNESS GROUP
20 WIRING SCHEMATIC
22 Hardware Identification & Torque Specifications

HANDLE PARTS GROUP
TP 400-5009-1-CW-N
Manual No. 7006933 FIELD & BRUSH MOWER
SERIES 0
4

HANDLE PARTS GROUP
Footnotes:
TP 400-5009-1-CW-N
Manual No. 7006933FIELD & BRUSH MOWER
SERIES 0 5
Part No Descri
p
tionItem Qt
y
Note
1 1719965 1 GRIP, Handle
2 7058960 1 LEVER, Blade Clutch Engage (weldment) replaces 1723595
3 7027802 1 CABLE, Throttle, Kawasaki part number stamped on cable
3 7027394 1 CABLE, Throttle, Briggs part number stamped on cable
4 7014871 2 LUBE FITTING, 3/16” hole
5 7091686 2 SCREW, 1/4-20 x 3/4” Hex Washer Self-Tap
6 7029167 1 DECAL, Throttle, Brush Cutter see Decals group
7 1723550 1 BRACKET, Blade Engage Lock
8 7091318 10 SCREW, 5/16-18 x 3/4” Hex Head Cap, GR 5
9 7028200 1 SWIVEL, Adjustable, 5/16-18 thread
10 7059204 1 LEVER, Transmission Drive (weldment) replaces 1723573
11 7091601 15 NUT, 5/16-18 Hex Flange Lock, GR 5
12 7090913 2 SCREW, #10-24 x 1/2” Hex Washer Self-Tap
13 1723553 1 CONTROL DECK & DASH PANEL (weldment)
14 7091813 4 SCREW, 1/4-20 x 1-3/4 Hex Head Cap, GR 5
15 7091298 8 NUT 5/16-18 Hex Nyloc
16 7011791 3 RETAINER, 5/16” Bolt
17 7072487 1 BRACKET, Handle Pivot, RH
18 7023354 1 SWITCH, Seat NC
19 1723569 2 HANDLE, Lower
20 1723564 1 SPRING, Safety Return
21 1723561 1 WELDMENT, Safety Bar
22 7044927 1 BRACKET, Safety Bar Pivot, LH replaces 1723566
23 7033736 1 HANDLE, Upper was 1723572
24 1719968 1 COVER, Foam was 1723568
25 7090209 6 SCREW, 5/16-18 x 1” Hex Head Cap, GR 2
26 7091540 4 SCREW, 5/16-18 x 1-1/2” Hex Head Cap, GR 5
27 1723570 2 BEARING, 3/4 I.D.
28 1725232 1 WELDMENT, Drive Engagement Bar
29 1725233 1 GRIP, Reverse Handle
30 7090122 2 WASHER, 3/8 SAE Flat
31 7091518 2 NUT, 3/8-24 Hex Nyloc
32 7091294 8 WASHER, .28 x .63 x .06 Flat
33 7091310 2 HAIR PIN, #13
34 1723554 2 BALL JOINT, Type R (5/16-24 thread)
35 1723556 1 NUT, 3/8-24LH Hex Jam
36 1723557 1 BALL JOINT LH (3/8-24 LH thread)

HANDLE PARTS GROUP
TP 400-5009-1-CW-N
Manual No. 7006933 FIELD & BRUSH MOWER
SERIES 0
6

HANDLE PARTS GROUP
Footnotes:
TP 400-5009-1-CW-N
Manual No. 7006933FIELD & BRUSH MOWER
SERIES 0 7
Part No Descri
p
tionItem Qt
y
Note
37 7092031 1 NUT, 5/16-24 Hex Jam
38 1723555 1 ROD, Trans. Engage, Lower (3/8-24 LH & 5/16-24 threads)
39 1723351 1 BRACKET, Deck Safety Switch
40 1723552 1 SWITCH, Deck Safety
41 1723662 1 BOLT, 1/2 x 1-3/16 to 3/8-16 Shoulder
42 7041868 1 SPACER, Transmission, Express
43 7090188 1 WASHER, 5/16” SAE Flat
44 1723596 1 BRACKET, Clutch Engage Lever
45 7091908 4 SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5
46 7091603 4 NUT, 1/4-20 Hex Nyloc
47 7010745 1 BALL JOINT, 3/8-24 Thread
48 1725231 1 ROD, Trans. Engage, Upper (3/8-24 thread)
49 7076938 1 SCREW, 5/16-18 x 2-1/4” Hex Head Cap, GR 5
50 7029495 2 CAP, Push Plastic
51 7012080 3 CABLE TIE, 7”
52 1723616 1 BRACKET, Fuel Tank
53 7091619 1 NUT, 3/8-16 Hex Flange Lock

ENGINE DECK GROUP
TP 400-5009-1-CW-N
Manual No. 7006933 FIELD & BRUSH MOWER
SERIES 0
8

ENGINE DECK GROUP
Footnotes:
TP 400-5009-1-CW-N
Manual No. 7006933FIELD & BRUSH MOWER
SERIES 0 9
Part No Descri
p
tionItem Qt
y
Note
1 7091318 10 SCREW, 5/16-18 x 3/4” Hex Head Cap, GR 5
2 1723549 1 PLATE, Clutch Cover
3 7091511 4 NUT, 5/16-18 Hex, GR 5 or B
4 7090187 18 WASHER, 5/16” Split Lock
5 1704723 2 CAP, Black
6 1723803 1 DECK, Engine (weldment)
7 7091302 24 NUT, 3/8-16 Hex, GR 5 or B
8 7091320 22 WASHER, .38 x .68 x .09 Split Lock
9 1723806 1 BOSS, Idler Arm Pivot
10 1723805 2 SLEEVE BUSHING, 3/4 ID
11 1723804 1 IDLER ARM, Transmission (weldment)
12 1723592 1 COVER, Engine Back
13 7091540 4 SCREW, 5/16-18 x 1-1/2” Hex Head Cap, GR 5 engine mount bolts
14 7090001 2 BOLT, 5/16-18 x 3/4” Short Neck Carriage, GR 5
15 1723807 1 SPRING, Idler
16 1723808 1 ROD, Idler Tension (3/8-16 thread)
17 7090122 9 WASHER, 3/8 SAE Flat
18 7092055 1 SCREW, 3/8-16 x 3-1/4” Hex Head Cap, GR 5
19 1723583 1 PULLEY, Idler
20 7091497 1 SCREW, 3/8-16 x 1-1/2” Hex Head Cap, GR 5 was 91553 (1-3/4” long)
21 1723591 1 PLATE, Lower Handle Mount
22 7091619 12 NUT, 3/8-16 Hex Flange Lock or 90613
23 7076941 2 SCREW, 3/8-16 x 1-1/4” Hex Head Cap, GR 5
24 7091304 7 SCREW, 3/8-16 x 1 Hex Head Cap, GR 5
25 1723585 1 SPACER, Engine Shaft
26 1723586 1 PULLEY, Blade Clutch Drive
27 7091601 2 NUT, 5/16-18 Hex Flange Lock, GR 5
28 1723588 1 PULLEY, Trans. Drive
29 7091807 1 WASHER, 7/16” Flat (heavy duty)
30 7091301 1 WASHER, 7/16” Split Lock
31 1723589 1 CAPSCREW, 7/16-20 x 1-12” Socket Head
32 1723620 1 TRANSAXLE
33 1723590 1 KEY, 1/4” Square x 2-1/8” (engine shaft)
34 7072386 2 KEY, 3/16” Square x 2-3/16”
35 7029738 2 RETAINING RING, 3/4” External
36 7031965 4 WASHER, 3/4” I. D. Thrust
37 1723580 1 DRIVE WHEEL, Left not shown
**Purchase engine & engine parts other than those listed from engine service outlets.

ENGINE DECK GROUP
TP 400-5009-1-CW-N
Manual No. 7006933 FIELD & BRUSH MOWER
SERIES 0
10

ENGINE DECK GROUP
Footnotes:
TP 400-5009-1-CW-N
Manual No. 7006933FIELD & BRUSH MOWER
SERIES 0 11
Part No Descri
p
tionItem Qt
y
Note
38 1723581 1 DRIVE WHEEL, Right
39 7091501 1 SCREW, 3/8-16 x 2-1/2” Hex Head Cap, GR 5
40 1723579 1 PULLEY, Blade Clutch Idler
41 1723577 1 IDLER BOSS
42 1723576 1 ROD, Blade Clutch Idler Tensioning (3/8-16 thread)
43 7076938 4 SCREW, 5/16-18 x 2-1/4” Hex Head Cap, GR 5
44 1723575 1 HANGER, Trans. Forward Mount
45 7072520 1 BRACKET, Clutch Support
46 1723622 1 PLATE, Lock Engage
47 7091686 2 SCREW, 1/4-20 x 3/4” Hex Washer Self-Tap
48 1723621 1 BRACKET, Lock Lever (weldment)
49 7091536 1 SCREW, 1/4-28 x 5/8” Hex Head Cap, GR 8
50 7090052 1 WASHER, 1/4” Split Lock
51 7091294 3 WASHER, .28 x .63 x .06 Flat
52 1723614 1 **ENGINE, Briggs 13.5HP (not shown) model 21B977, type 0120, trim
E1
52 1723615 1 **ENGINE, Kawasaki 15HP (not shown) model FH451V, type AS02
53 7072515 1 BRACKET, Fuel Tank Bottom (not shown) Briggs part# 225903
**Purchase engine & engine parts other than those listed from engine service outlets.

MOWER DECK PARTS GROUP
TP 400-5009-1-CW-N
Manual No. 7006933 FIELD & BRUSH MOWER
SERIES 0
12

MOWER DECK PARTS GROUP
Footnotes:
TP 400-5009-1-CW-N
Manual No. 7006933FIELD & BRUSH MOWER
SERIES 0 13
Part No Descri
p
tionItem Qt
y
Note
1 7091511 10 NUT, 5/16-18 Hex, GR 5 or B
2 7090187 10 WASHER, 5/16” Split Lock
3 1723532 1 WELDMENT, Front Bumper
4 1723533 23 CHAIN CURTAIN
5 7091540 3 SCREW, 5/16-18 x 1-1/2” Hex Head Cap, GR 5 for bumper rear holes
6 1723534 1 BRACKET, Chain Curtain
7 1723535 1 ROD, Chain Curtain Mounting
8 7091304 4 SCREW, 3/8-16 x 1 Hex Head Cap, GR 5
9 7091320 9 WASHER, .38 x .68 x .09 Split Lock
10 1723536 1 LEFT SKID, Blade Deck (weldment) not shown
11 1723537 1 RIGHT SKID, Blade Deck (weldment)
12 7091302 8 NUT, 3/8-16 Hex, GR 5 or B
13 7091318 4 SCREW, 5/16-18 x 3/4” Hex Head Cap, GR 5
14 1723538 1 BRACKET, Anti-Torque
15 1723657 1 SPRING, Clutch
16 1723539 1 ROD, Blade Clutch Engagement (5/16-18 threaded)
17 7091497 5 SCREW, 3/8-16 x 1-1/2” Hex Head Cap, GR 5
18 -- 1 WASHER, 7/16 I.D. x 1-1/2” Flat (Heavy Duty) this fastener is furnished with
the clutch
19 1723540 1 ASSEMBLY, Clutch Brake (Noram part no. CB84S)
20 -- 1 SCREW, 5/16-18 x 1” Hex Head Cap this fastener is furnished with
the clutch
21 -- 1 NUT, 5/16-18 Hex Center Lock this fastener is furnished with
the clutch
22 1723541 1 SPACER, Clutch
23 7090122 3 WASHER, 3/8” SAE Flat
24 1723542 1 ASSEMBLY, Blade Spindle
25 1723543 1 CHANNEL, Cutting Blade Reinforcement
26 1723544 1 CUTTING BLADE
27 7090333 1 WASHER, 5/8” Split Lock
28 1725227 1 CAPSCREW, 5/8-11 x 1-1/2” Socket
29 1723546 1 DELFECTOR, Discharge (weldment)
30 7090188 2 WASHER, 5/16” SAE Flat
31 1723547 1 COVER, Discharge (weldment)
32 1723548 1 BLADE DECK
33 7091908 3 SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5 for bumper front holes
34 7028620 4 SPACER, .340 I.D. x .630 O.D. x .310 thick

DECALS GROUP
TP 400-5009-1-CW-N
Manual No. 7006933 FIELD & BRUSH MOWER
SERIES 0
14

DECALS GROUP
Footnotes:
TP 400-5009-1-CW-N
Manual No. 7006933FIELD & BRUSH MOWER
SERIES 0 15
Part No Descri
p
tionItem Qt
y
Note
1 7013010 3 DECAL, Danger, Cut Finger (CPSC)
2 7075893 1 DECAL, Personal Protection
3 7028490 1 DECAL, Warning, Brush Cutter
4 7073647 2 DECAL, Caution, Guard Catcher
5 1725229 1 DECAL, Transmission Drive
6 7028349 1 DECAL, Ignition/Cutting Blade
7 7029167 1 DECAL, Throttle, Brush Cutter
8 1725230 1 DECAL, Speed Adjuster
9 7073594 1 DECAL, Caution, Open Belt Drive
10 7075760 1 DECAL, SNAPPER, 8” long
11 7029331 1 DECAL, 25”
12 7071916 1 DECAL, SNAPPER, 14-1/2” long

ELECTRICAL & MISC. GROUP
TP 400-5009-1-CW-N
Manual No. 7006933 FIELD & BRUSH MOWER
SERIES 0
16

ELECTRICAL & MISC. GROUP
Footnotes:
TP 400-5009-1-CW-N
Manual No. 7006933FIELD & BRUSH MOWER
SERIES 0 17
Part No Descri
p
tionItem Qt
y
Note
1A 7044922 1 WIRE HARNESS, Briggs also shown on previous page
1B 1724057 1 WIRE HARNESS, Briggs also shown on previous page
1C 7044926 1 WIRE HARNESS, Kawasaki also shown on previous page
1D 1724058 1 WIRE HARNESS, Kawasaki also shown on previous page
2 1723618 1 FUEL TANK, Auxilliary
3 7012222 2 CLAMP, Fuel Hose
4 7023506 1 BEZEL
5 7012080 2 CABLE TIE, 7”
6 1723635 1 BRACKET, Battery Hold Down
7 7091314 2 WASHER, 1/4” Internal Lock
8 1723563 1 SWITCH, Bail (not shown) used on early production units
only
9 1723637 1 CABLE, Battery Positive to Solenoid
10 7090052 3 WASHER, 1/4” Split Lock
11 1723636 1 SCREW, Tek #12 x 3/4” Hex Head Cap
12 1723639 1 CABLE, Solenoid to Starter
13A 7075622 1 SOLENOID - Super Trombetta - 2 Terminal GV3031730
13B 1723641 1 SOLENOID, Single Pole Simplicity solenoid used on early
production
14 1723631 1 SWITCH, Keyed Start
15 1723619 1 AUX FUEL LINE w/Clamps used on 13.5hp Briggs & 15hp
Kawasaki
16 7091495 2 SCREW, 1/4-20 x 3/4” Hex Head Cap, GR 5
17 7091576 2 NUT, 1/4-20 Hex, GR 5 or B
18 1723629 1 BELT, Blade Clutch 5L Sect.; 67.40 effective length
19 1723630 1 BELT, Transmission AX Sect.; 30.10 effective length
20 7029130 1 BATTERY, 12V, 3 Amp, 190 Cold Cranking Amp (Incl. Drain
Tube)
21 1725226 1 CABLE, Battery Negative to Ground
22 7029332 1 GROUND WIRE, 16 Ga., Green, 19” long

WIRING HARNESS GROUP
TP 400-5009-1-CW-N
Manual No. 7006933 FIELD & BRUSH MOWER
SERIES 0
18

WIRING HARNESS GROUP
Footnotes:
TP 400-5009-1-CW-N
Manual No. 7006933FIELD & BRUSH MOWER
SERIES 0 19
Part No Descri
p
tionItem Qt
y
Note
1A 7044922 1 WIRE HARNESS, Briggs
1B 1724057 1 WIRE HARNESS, Briggs Simplicity p/n used on early
production
1C 7044926 1 WIRE HARNESS, Kawasaki
1D 1724058 1 WIRE HARNESS, Kawasaki Simplicity p/n used on early
production

WIRING SCHEMATIC
TP 400-5009-1-CW-N
Manual No. 7006933 FIELD & BRUSH MOWER
SERIES 0
20