Snapper CLT195420 (7800313) Manual

1
SET-UP INSTRUCTIONS & PRE-OPERATION CHECKLIST for SNAPPER
19” STEEL DECK WALK BEHIND MOWERS
INTRODUCTION: The SNAPPER 19” Walk Behind Mowers are shipped almost fully assembled and require
minimal set-up. Complete each of the following steps carefully. Review and complete each item as instructed
on the Pre-Operation checklist. The Snapper Product Registration card must be filled out and sent to Customer
Service department at Snapper when completed.
STEP 1: Remove machine from shipping carton. Machine
is shipped in carton with handles disconnected. Remove
and discard cardboard from between all handles. Raise
upper handle until it is seated in both lower handles.
Securely tighten handle T-Knobs on both sides. Position
handles and secure with nuts and bolts to the lower deck
brackets. Tighten nuts and bolts securely. See Figure 1.
NOTE: Handles are mounted on the inside of the deck
brackets. Insert bolts so that the nuts will be towards the
inside of the brackets. See Figure 2.
FIGURE 1
IMPORTANT: DO NOT tip machine with carburetor or
spark plug down. Oil from crankcase will saturate the air
filter and cause the engine to be hard to start or not start
at all. If contamination does occur, the air filter will have to
be replaced.
STEP 2: Tip mower back against the upper handle to gain
access to cutting blade. Remove foam shipping block
from cutting blade. This must be removed before starting
the engine.
STEP 3: Route recoil rope up to rope guide on upper
handle. Move blade control bail up to handle. Pull recoil
handle to extend rope past guide. Insert rope into guide.
STEP 4: Handle height is adjustable for different height of
operators. Loosen the two nuts on the inside of each of
the lower handles. See Figure 2. Move the handle up or
down to the desired height. Retighten all nuts securely
after adjustment.
FIGURE 2
STEP 5: CHECKLIST: Complete all items on the Pre-
Operation Checklist as instructed.
INSTRUCTION NO. 7-5114 (I.R. 6/21/02)
T-KNOBS
LOWER HANDLE
NUTS
UP
PER
HANDLE
LOWER
HANDLE
LOWER
BRACKETS
ROPE
GUIDE
RECOIL ROPE
BLADE
CONTROL BAIL

2
PRE-OPERATION CHECKLIST for SNAPPER
19” STEEL DECK WALK BEHIND MOWERS
Snapper has completed initial adjustments and performed operational tests prior to shipping the machine. Due
to the possible effects of shipping, handling and storage, Snapper intends for all of the following items to be
verified and necessary final adjustments made at time of setup. It remains good practice and is strongly
recommended that all the items also be checked prior to placing the machine into service. It is very important
that setup is verified and all operational tests completed and results are acceptable. After completing this form,
sign and retain for future reference.
SET-UP
_____ FOAM SHIPPING BLOCK removed from cutting blade.
_____ UPPER HANDLE & LOWER HANDLE secured in place and hardware tightened securely.
_____ SIDE CHUTE, RECYCLING COVER or GRASS BAG installed on mower.
_____ BLADE retaining bolt(s) checked and tightened securely.
LUBRICATION
_____ ENGINE OIL added to bring level up to full mark on 4-cycle engines (Refer to Engine Manual).
OPERATIONAL TEST
_____ ENGINE started, engine control settings checked and adjusted as needed.
CPSC (Consumer Product Safety Commission) COMPLIANCE TEST
_____ BLADE CONTROL stops engine when released.
CONSUMER INFORMATION
Purchase Date ___________________ Model_______________________ Serial No.________________________
Retailers Name ___________________________________ Signature ____________________________________
Address _____________________________________ City ____________________ State _______ Zip _______
MOWER WILL BE USED COMMERCIALLY? _______ YES _____ NO
Purchaser’s Name _________________________________ Signature ____________________________________
Address ____________________________________ City _____________________ State _______ Zip _______
IMPORTANT: This form is to be retained for future reference regarding Warranty, proof of purchase, traceability
for product recall or service, etc. Complete the Product Registration Card and Mail to Customer Service
Department at SNAPPER, P.O. BOX 1379, McDonough, Georgia, 30253.
INSTRUCTION NO. 7-5114 (I.R. 6/21/02)