SOARING MODELS Mini Dart 2 User manual

Mini Dart 2 _____ SoaringModels
Assembly instruction _____ 2020
1
Kit components
1- Wing
2- Fuselage with nose cone
3- Fin
4- Stabilizer

Mini Dart 2 _____ SoaringModels
Assembly instruction _____ 2020
2
Accessories components
1- Servo frame
2- Peg
3- Tail rods
4- Crimping tubes for tail rods
5- Aileron’s horns
6- Fin horn
7- Stabilizer horn
8- Tube for rods
9- Aileron’s rods
10-Wing screws M2.5*10, M2.5*12
11-Tail screws M2*6
12-Shrinkable tube for torsions
13-Tail torsions

Mini Dart 2 _____ SoaringModels
Assembly instruction _____ 2020
3
Recommended electronic components
1- Battery 1S 250-500 mAh
2- Dymond D-47 *4
3- Receiver 4-8 channels
Tools and materials for assembling
1- Ruler
2- Files
3- Sand paper
4- Knife
5- Cyanoacrylate
6- Epoxy
7- Two-side tape

Mini Dart 2 _____ SoaringModels
Assembly instruction _____ 2020
4
Mounting of control horns
Cut the slots for the control horns and aileron rods with a knife according to the
pictures.
In rudder on the right side in the middle.
In elevator at the top side.
In ailerons at the distance of 5 mm from the aileron beginning.
File out control horns before gluing.
Avoid contact of superglue with foam of the wing and tail cores!
Paste in control horns using epoxy.

Mini Dart 2 _____ SoaringModels
Assembly instruction _____ 2020
5
Heat shrink tubes at the both ends of torsions
Make holes for torsions with a drill 1mm or needle, install torsions with epoxy

Mini Dart 2 _____ SoaringModels
Assembly instruction _____ 2020
6
Peg installation
Prepare peg for gluing using file
Make a slot for peg using drill and file. Distance from peg to wing tip 12-15mm.
Glue peg with epoxy or cyanoacrylate.

Mini Dart 2 _____ SoaringModels
Assembly instruction _____ 2020
7
Fuselage assembling
Make holes in fuselage for rods and tubes according to the photos and glue tubes for
aileron rods
File out spot for tail boom on fin surface
Insert fin into slot in tail boom set it vertically and fix with cyanoacrylate

Mini Dart 2 _____ SoaringModels
Assembly instruction _____ 2020
8

Mini Dart 2 _____ SoaringModels
Assembly instruction _____ 2020
9
Servos installation
Screw on servos into frame and insert it into fuselage, glue frame to fuselage.
For better CG servos in carbon fuselage should be far from nose as much as possible.
Set aileron servos horns 30-40 degrees back at neutral servos position.
Mark hole position and bend the rod, cut the rest of wire.

Mini Dart 2 _____ SoaringModels
Assembly instruction _____ 2020
10
Set servos horns to neutral position.
Lay rods through fuselage, put tubes 5mm length on rods and glue them between two
servos.
Set neutral position of tail servos, rudder and elevator.
Crimp tube on cable.
On the end of elevator rod add 40-50mm spread or wire for easy assembling

Mini Dart 2 _____ SoaringModels
Assembly instruction _____ 2020
11
Settings and flight modes
Recommended CG position 58-62 mm from leading edge
Launch mode –ailerons 1mm up Cruise - 0
Normal flight –2mm down Thermal –4-9mm down
Brakes –maximum down