SOARING MODELS Kite 2P User manual

Kite 2P Soaring Models
Assembly instruction 2021
1
Kit components
Wing
Wing joiner
Fuselage with nose cone
Fin
Stabilizer
Aileron carbon rods
Plastic tubes for tail wires
Accessories

Kite 2P Soaring Models
Assembly instruction 2021
2
Accessories components
1- Tail torsions
2- T-peg
3- Crimping tubes for tail rods
4- Aileron axis
5- Aileron rod ends
6- Tail rods
7- Stabilizer horn
8- Fin horn
9- Ailerons horns
10-Reinforcement for ailerons axis
11-Rear wing screw M3*10 (+1 spare)
12-Front wing screw M3*12 (+1 spare)
13-Stab screws M3*6 2pcs (+2 spare)

Kite 2P Soaring Models
Assembly instruction 2021
3
Recommended electronic components
1- Battery 1S 300-500 mAh
2- Servos KST X-08H*2 + D47*2
3- Receiver 4-6 channels
Tools and materials for assembling
1- Ruler
2- Files
3- Sand paper
4- Knife
5- Cyanoacrylate
6- Epoxy
7- Two-side tape

Kite 2P Soaring Models
Assembly instruction 2021
4
Tail assembling
Cut the slots for the control horns and aileron rods with a knife according to the
pictures.
In rudder on the right side in the middle.
In elevator at the top side.
File out control horns before gluing.
Paste in control horns using epoxy with filler.
Make a holes for torsions with a needle, install torsions and fix them with cyanoacrylate.

Kite 2P Soaring Models
Assembly instruction 2021
5
Wing assembling
Clean up from foam slots for aileron horns and check is it fits good without glue.

Kite 2P Soaring Models
Assembly instruction 2021
6
File out control horns axis and spot for axis gluing.
Paste in control horns using epoxy with filler.

Kite 2P Soaring Models
Assembly instruction 2021
7
While epoxy is liquid press down axis to the slot in wing and fix it with CA.

Kite 2P Soaring Models
Assembly instruction 2021
8
Glue two layers of carbon about 8mm width from accessories set to reinforce axis
fixation using CA and a piece of film
Cut the rest of carbon and sand.

Kite 2P Soaring Models
Assembly instruction 2021
9
Prepare t-peg for gluing using file
Make a slot for peg using knife, file and wire.

Kite 2P Soaring Models
Assembly instruction 2021
10
Fill slot with epoxy and paste t-peg

Kite 2P Soaring Models
Assembly instruction 2021
11
Servos installation
Fix LiPo in the fuselage with 2-side tape and check if nose cone fits good
Wrap servos with paper tape and thread.
Cut servos control horns. Center distance should be about 7-8 mm.
Expand holes close to the wall of fuselage with the file.

Kite 2P Soaring Models
Assembly instruction 2021
12
Make a holes for tail servos horns with a file or Dremel. Holes dimensions 2*16mm.
Distance from left and right sides 2mm. Glue servos like on photos.

Kite 2P Soaring Models
Assembly instruction 2021
13
File out steel ends of ailerons rods and make scratches for better gluing.
Split end of carbon tube insert steel rod (aileron side first), fill with glue and wrap it
in aramid thread fast.

Kite 2P Soaring Models
Assembly instruction 2021
14
Make holes for aileron rods according to the pictures.

Kite 2P Soaring Models
Assembly instruction 2021
15
Connect rods to aileron horns, screw up wing to fuselage and glue forward ends of
rods. Servos should be in zero position and ailerons 15 mm down.

Kite 2P Soaring Models
Assembly instruction 2021
16

Kite 2P Soaring Models
Assembly instruction 2021
17
Tail linkage
Fix wire on tail horns with the
crimping tubes.
For stabilizer removing make a loop
with 50-80mm spread or wire for easy
assembling.
Set neutral position of tail servos,
rudder and elevator.
Glue a piece of steel rod to end of tail
wire and lie it into fuselage with a magnet

Kite 2P Soaring Models
Assembly instruction 2021
18
Settings and flight modes
All settings have advisory character and depends of your piloting style
Settings can be changed because of just a little deviation of CG position
and weather
All models should be carefully checked and trimmed before full launch
CG
72-76
elevator
+
-
10
8
rudder
+
-
15
15
ailerons
+
-
12
9
launch
ailerons
elevator
1
0
0.7 mm
up
2
0.5 mm
up
0.5 mm
down
speed
ailerons
elevator
0.5 mm
up
0.5 mm
down
normal
ailerons
elevator
0
0
thermal
ailerons
elevator
6 mm
down
1 mm
down
brakes
ailerons
elevator
50 mm
down
6 mm
down