socomec SNMP Card II User manual

SNMP Card II
STATYS XS – SNMP HTTP AGENT
GB
www.socomec.com
OPERATING
MANUAL

3GB
SNMP CARD II - SOCOMEC
ELECTRONIC EMISSION NOTICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
1. WELCOME. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
1.1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
1.2. SNMP CARD II Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
1.3. SNMP CARD Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
1.4. System Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
2. CONNECT SNMP CARD TO THE NETWORK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
2.1. What you need. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
2.2. Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
2.3. SNMP Card Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
2.4. SNMP CARD Configuration through TELNET command . . . . . . . . . . . . . . . . . . . . . . . . . . .10
2.5. SNMP CARD Configuration through a Web Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
2.6. SNMP CARD Initial Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
3. MANAGING SNMP CARD/STATYS XS VIA WEB BROWSER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.1. Utilising the SNMP CARD Home Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
3.2. STATYS XS Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
3.3. ATS Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
3.4. SNMP CARD Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
3.5. ATS History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
3.6. Language Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
4. MANAGING SNMP CARD /STATYS XS VIA SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4.1. Setting SNMP parameters in SNMP CARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
4.2. SNMP Access Control Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
4.3. SNMP Trap Receivers Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
4.4. Set up SNMP Manager Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
5. APPENDIX A TECHNICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
5.1. Technical Information about SNMP CARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
6. APPENDIX B FIRMWARE UPGRADES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
6.1. General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
6.2. Updating SNMP CARD Firmware from Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
7. APPENDIX C HTTP SECURITY CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
8. APPENDIX D HOW TO DO WHEN FORGET THE ACCOUNT & PASSWORD . . . . . . . . . . . . . . . . .36
GB CONTENTS

4GB SNMP CARD II - SOCOMEC
AT, IBM is registered trademarks of International Business Machines Corporation.
NetWare are registered trademarks of Novell, Incorporated.
All other trademarks belong to their respective proprietors.
ELECTRONIC EMISSION NOTICE
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protec-
tion against harmful interference when the equipment is operated in a commercial environment.
CE Notice
This device complies with the EMC directive of the European Community and meets or exceeds
the following technical standard:
• EN 55022:1998-- ”Limits and Methods of Measurement of Radio interference Characteristics
of information Technology Equipment.” This device complies with the CISPR Class B standard
• EN 55024:1998-- ”Electromagnetic compatibility-- Generic immunity standard Part1:
Residential, and light industry.”
SAFETY INFORMATION
For SNMP CARD (Card Type)
• All the service of this equipment must be perform by qualified service personnel. Remove
rings, watches and other jewelry before servicing the unit

5GB
SNMP CARD II - SOCOMEC
1. WELCOME
1.1. Introduction
SNMP CARD – acronym for STATYS XS SNMP and HTTP Agent. It displays the STATYS XS sta-
tus and issue commands to the STATYS XS. User can use SNMP managers or Web browsers
to manage the STATYS XS through an Ethernet.
SNMP CARD II:
The SNMP Card II is an internal card (as shown in Figure 1-1) designed for STATYS XS models,
where the SNMP Card can be inserted into the extension slot of the STATYS XS.
Figure 1-1 SNMP CARD (Card Type)
1.2. SNMP CARD II Resources
The SNMP CARD CD-ROM contains Upgrade software, Quick Installation Guide, User Guide,
MIB files, central management software-Remote View & manual.
1. SNMP CARD Quick Installation Guide is a startup guide on installing and configuring a
SNMP CARD using a Windows OS workstation.
2. SNMP CARD User Guide provides user with details and information on installation and con-
figuration of SNMP CARD.
3. SNMP CARD online help is available providing additional instructions not found in the manual.

6GB SNMP CARD II - SOCOMEC
1.3. SNMP CARD Package Contents
1. SNMP CARD with mounting bracket
2. SNMP CARD CD-ROM containing Upgrade software, Quick Installation Guide, User Guide,
MIB files. If not available please refer to www.socomec.com/download-ups-software_en.html
FEATURES
• Network connection through RJ45 connector
Allow the STATYS XS to connect directly to the network through a RJ45 connector without us-
ing RS232 ports on the computer and without loading any individual STATYS XS management
software on the network server.
• Network management
Allow remote management of the STATYS XS from any workstation through Internet or Intranet.
• Remote monitoring via SNMP, HTTP
Allows monitoring of the STATYS XS using SNMP CARD MIB (Management Information Base) –
via SNMP CARD and Internet Browser.
• Configure STATYS XS and SNMP CARD functions from any client (password protected)
Set STATYS XS and SNMP CARD parameters from any SNMP management station or through
Internet Browsers using HTTP forms and objects.
• Keep event logs & metering data in flash memory
Provide event log of STATYS XS power parameters, power quality, STATYS XS status.
… also
• Notification of system administrator via SNMP Traps
• RTC supported
• Telnet support for configuration
• BOOTP/DHCP supported
• Online configuration supported
• Enhanced HTTP security
• No restart needed for IP change
• System parameters/log write to flash memory simultaneously
• SSH and SSL supported
• Can connect an EMD (Environmental Monitoring Device) to detect the temperature and humidity.
• NTP & ICMP supported
• SNMP V3 supported
• IPV6 supported

7GB
SNMP CARD II - SOCOMEC
1.4. System Application
SNMP CARD is a communication interface between STATYS XS and the network. SNMP CARD
supports two kinds of protocol – SNMP and HTTP for user access. Through the SNMP NMS
and Web Browser, user can obtain the STATYS XS status, issue commands to STATYS XS and
setup the SNMP CARD through the network.

User’s
computer
STATYS XS
SNMP Card
NMS
Work staƟon
or web
Ethernet Ethernet
Remote view
tŽƌŬƐƚĂƟŽŶ
Remote view
tŽƌŬƐƚĂƟŽŶ
Remote view
tŽƌŬƐƚĂƟŽŶ
Figure 1-2 SNMP CARD System Application Diagram

8GB SNMP CARD II - SOCOMEC
2. CONNECT SNMP CARD TO THE NETWORK
2.1. What you need
To install SNMP CARD on a network and change its default configuration, you need a worksta-
tion running Microsoft Windows. If you are using dynamic IP addressing, all you need is a work-
station with a Web Browser.
2.2. Hardware Installation
1. Mount the SNMP CARD to SNMP CARD bracket provided.
2. Insert the SNMP CARD into the STATYS XS external communication slot. (Figure 2.1)
3. Tighten the screws of the SNMP CARD bracket.
Figure 2-1 SNMP CARD Installation
2.3. SNMP Card Configuration
Upgrade tool
1. Copy the Upgrade utility to the desktop 2. Click Discover to search SNMP card IP address

9GB
SNMP CARD II - SOCOMEC
3. Click Browse to open webpage (support DHCP) 4. The webpage display the SNMP overview
5. If DHCP is disable, please click “Modify” to create
the setting page.set Account and Password
6. (Default Account: SNMP / Password: admin)
7. Click “Set IP” to input the “IP - SubMask - Gateway” 8. Press “OK”
9. Modify IP successfully

10 GB SNMP CARD II - SOCOMEC
2.4. SNMP CARD Configuration through TELNET command
4. Make sure that you have a TCP/IP network already installed.
5. Run command shell
6. SNMP CARD will initially try to acquire an IP address from the DHCP network service, if
available on the network.
7. Type “Telnet <IP address obtained from DHCP>” and press enter.
8. If DHCP network service is not available on the network, contact your network administrator
to get an IP address for you workstation that has the same network’s address as the SNMP
CARD’s default IP address. The SNMP Card default IP address is 172.17.XXX.ZZZ where
XXX and ZZZ is the last two pairs of the MAC address in decimal located on the SNMP
CARD.
9. Type “Telnet 172.17.XXX.ZZZ” command and press enter. Password is admin.
2.5. SNMP CARD Configuration through a Web Browser
HARDWARE PREPARATION OF SNMP CARD
1. Procure a workstation with Ethernet card and Web Browser installed.
2. Connect the network cable (twisted-pair cable) from the workstation’s LAN port to an active
10/100-hub port.
3. Connect another network cable (twisted-pair cable) from the SNMP CARD LAN port to an
active 10/100-hub port.
4. Set the SNMP CARD DIP-switches, the switches 1 and 2 are OFF.
5. Turn on the STATYS XS and wait for SNMP CARD to boot up (around 90 seconds).

11GB
SNMP CARD II - SOCOMEC
CONFIGURATION THROUGH AWEB BROWSER
Normally, the first time you use SNMP card, the workstation is unable to communicate with the
SNMP card as they are not in the same IP subnet. However, you may use the “route add” com-
mand to configure the network routing table in the workstation to complete the SNMP card’s
configuration. If the IP address of the machine is in the same subnet as SNMP, just run the web
browser.
1. Using a workstation running on Microsoft Windows set up the TCP/IP protocol.
2. Connect the network cable to the Network port of the SNMP card.
3. Run command shell and enter the following command to add a routing condition:
Route add 172.17.7.18 210.67.192.147
Assume the IP address of the workstation is 210.67.192.147.
Note: The SNMP Card default IP address is 172.17.XXX.ZZZ where XXX and ZZZ are the last two
pairs of the MAC address in decimal located on the SNMP CARD.
Example: MAC address: 00 E0 D8 04 0A 15, IP address: 172.17.10.21
RUNNING THE WEB BROWSER (INTERNET EXPLORER OR CHROME)
1. Make sure that you have a TCP/IP network already installed.
2. If there is no DHCP network service on the network, contact your network administrator to get
an IP address for you workstation that has the same network’s address as the SNMP CARD’s
default IP address. The default IP address of SNMP CARD is 172.72.XXX.ZZZ where XXX and
ZZZ are the last two pairs of the MAC address in decimal located on the SNMP CARD.
3. Start your Web Browser.
4. Enter the URL “http:\\172.72.XXX.ZZZ” in the address box where XXX and ZZZ is the last
two pairs of the MAC address of SNMP CARD in decimal.
5. The SNMP CARD home page will be shown as below. (Figure 2-3)
Figure 2-3 SNMP CARD home page screen: Overview.

12 GB SNMP CARD II - SOCOMEC
2.6. SNMP CARD Initial Configuration
1. Select SNMP CARD Configuration from the SNMP CARD Management of the main menu to
setup the network configuration parameters (Figure 2-4).
2. Click the Become Administrator button at the bottom of the screen. Enter SNMP as the login
name and admin as the password. (Case sensitive)
3. Enter the SNMP CARD IP address.
4. Enter the SNMP CARD Gateway Address in the network.
5. Enter the SNMP CARD Subnet Mask of the network.
6. Click the Set Values to save the settings.
7. Select Date and Time from the SNMP CARD Management of the main menu and enter the
appropriate date and time information in the specified format.
8. Select Set Values to save the date and time settings.
9. Select SNMP CARD Control to enable or disable the network protocols (Figure 2-5).
10.Select Apply to save the changes.
Figure 2-4 SNMP CARD initial configuration page screen.

13GB
SNMP CARD II - SOCOMEC
Figure 2-5 SNMP CARD Control page screen.

14 GB SNMP CARD II - SOCOMEC
3. MANAGING SNMP CARD/STATYS XS VIA WEB BROWSER
3.1. Utilising the SNMP CARD Home Page
Start your Web Browser and enter SNMP CARD IP address
The SNMP CARD home page will be shown on the screen.
Select the help icon located at the bottom of each page for a detail description of each item.
3.2. STATYS XS Monitoring
Monitoring STATYS XS Input-output voltage, frequency, current, load, real-time abnormal
events, status and parameter settings.
OVERVIEW
This page shows a snapshot of all the main STATYS XS parameters as shown in Figure 3-1.
The page will refresh automatically. To set the refresh time, select the menu SNMP CARD Man-
agement – Homepage Refresh Rate.
Figure 3-1 SNMP CARD home page screen: Overview.

15GB
SNMP CARD II - SOCOMEC
ATS INFORMATION
Select “ATS Information” from the ATS Monitoring menu of the home page to view ATS and
SNMP CARD Identification Parameters (Figure 3-2).
Figure 3-2 SNMP CARD STATYS XS Monitoring page screen: ATS Information
INPUT PARAMETERS
Select Input Parameters from the ATS Monitoring on the main menu to view STATYS XS input
parameters (Figure 3-3).
Figure 3-3 SNMP CARD STATYS XS Monitor page screen: STATYS XS Input Parameters

16 GB SNMP CARD II - SOCOMEC
OUTPUT PARAMETERS
Select Output Parameters from the ATS Monitoring on the main menu to view STATYS XS out-
put parameters (Figure 3-4).
Figure 3-4 SNMP CARD STATYS XS Monitor page screen: STATYS XS Output Parameters
SETTING PARAMETERS
Select Setting Parameters from the ATS Monitoring on the main menu to view STATYS XS Set-
ting Parameters (Figure 3-5).
Figure 3-5 SNMP CARD STATYS XS Monitor page screen: Setting Parameters
ALARM LIST
Select Alarm List from the ATS Monitoring on the main menu to view alarms presents (Figure 3-6).
Figure 3-6 SNMP CARD STATYS XS Monitor page screen: Alarm List

17GB
SNMP CARD II - SOCOMEC
3.3. ATS Management
This section contains the control parameters of the STATYS XS connected to the SNMP CARD.
ATS CONTROL
This page allows user to turn on or off the Buzzer control and manually transfer source by click-
ing on the [Switch] button as shown below. (Figure 3-7)
Figure 3-7 SNMP CARD ATS Control screen
EMD CONFIGURATION
This EMD configuration allows user to configure the EMD parameters as shown below (Figure
3-8). Set the EMD status to Auto allows auto detection of EMD type. For more information about
EMD device setup, please see the EMD_ installation_ manual.
Figure 3-8 EMD Configuration screen

18 GB SNMP CARD II - SOCOMEC
3.4. SNMP CARD Management
In this section, you can view and modify the SNMP CARD control parameters.
All the sub-menus are available in read-only for all users, except the administrator has access in
read/write mode.
DATE AND TIME
This menu lets you set the SNMP CARD internal date and time. There are three ways to set the
Date and Time (Figure 3-9). Synchronize with computer time, Synchronize with NTP server or
set the date and time manually.
Figure 3-9 Date and Time
SNMP CONFIGURATION
Allows the administrator set the local network configuration parameters in SNMP CARD, includ-
ing the basic variables in SNMP management (Figure 3-10).
1. SNMP CARD IP Address: The IP address of the SNMP CARD in dotted format (e.g.
192.168.1.100).
2. SNMP CARD Gateway Address: The IP address of the network gateway in dotted format
(e.g. 192.168.1.254).
3. SNMP CARD Subnet Mask. The Subnet Mask for your network (e.g. 255.255.255.0).
4. System Name: SNMP model name
5. System Contact: SNMP Network Administrator
6. System Location: SNMP installed location
7. History Log Interval: Set the download interval time in seconds to download Input Voltage,
Output Voltage, Load, Capacity and Input frequency. These values are saved in the History
Log. The maximum value for this setting is 28800 seconds (i.e. 8 hours).
8. Extended History Log Interval: Set the download interval, in minutes, to create an extended
history log. After every interval, the STATYS XS parameters will be consolidated and mini-
mum, maximum and average values of these parameters will be stored as extended history
log. This value can range between 3 and 9000 minutes.
9. SNMP CARD Polling Rate (sec): Update interval rate in seconds which SNMP CARD up-
date the parameters from STATYS XS (range: 3, 5, 10, 30, 60)
10.SNMP CARD Baud Rate (sec): The data transmission rate between the STATYS XS and
SNMP CARD.
11.Default Language: Default language options included “English”, “Traditional Chinese”, “Sim-

19GB
SNMP CARD II - SOCOMEC
plified Chinese” and “Auto”. SNMP Card Home Page will be displayed using the language
set in the Web Browser if “Auto” is selected. (*): to be added soon.
12.Temperature Unit: Display the Temperature in Celsius or Fahrenheit.
Figure 3-10 SNMP Configuration
SNMP CONTROL
Allows the user to enable or disable the communication protocols available in the SNMP CARD
and affect a restart and reset of the SNMP CARD internal parameters. Some of the items in this
menu are visible only to administrator with read/write access rights. (Figure 3-11)
1. BOOTP/DCHP Status: Enabling or disabling the Boot Protocol (BOOTP) / Dynamic Host
Configuration Protocol (DHCP). These protocols are Internet standards used to get a dynam-
ic IP address from a BOOTP / DHCP server.
2. Ping Echo: Enabling or disabling the SNMP CARD to respond to Ping requests.
3. Network Upgrade: Enabling or disabling the Trivial File Transfer Protocol (TFTP) upgrade con-
trol. You can use upgrade.exe on Windows via TFTP to upgrade SNMP CARD firmware.
4. Telnet Connection: Enabling or disabling the terminal to server application (Telnet) control
process. The standard port is 23.
5. HTTP Support: Enabling or disabling the HTTP connection with the SNMP CARD. The user
may configure HTTP protocol to use a port number other than standard HTTP port (80).
6. SNMP Support: Enabling or disabling the SNMP connection with SNMP CARD. The user
may configure the SNMP protocol to use a port number other than the standard SNMP port
(161).
7. Reset Agent to Default: Instructs SNMP CARD to reset parameters to factory default value.
8. Restart Agent: Instructs SNMP CARD to restart.

20 GB SNMP CARD II - SOCOMEC
Figure 3-11 SNMP Control
SNMP UPGRADE
Allows user to upgrade SNMP firmware, as shown below Figure 3-12
Figure 3-12 SNMP Upgrade
ACCESS CONTROL
Displays the authentication parameters setting as shown below Figure 3-13.
Figure 3-13 Access Control