Sodex Sport S80102 Dimensions

1
DESCRIPTION
Steel structure Ø90
Powder coated
CONFORM
European norm
NF EN 16630
PRODUCT SHEET
ELLIPTICAL TRAINER
PRODUCT REF :S80102 UNIT
ASSEMBLY TIME
The assembly time for this elliptical trainer is estimated at 30 minutes with 2 people (without concreting).
MAINTENANCE
The equipement has to be regularly maintained by the owner. If one of the modules has to be repaired,
users should not be able to access to it until the repair is done. To ensure good use, routine visual ins-
pections are required, paying special attention to the following points: The cleanliness, ground clearance,
surface condition, visible foundations, sharp edges , missing parts, excessive wear of moving parts and
the structural integrity. Moreover, a more thourough functional check should be carried out every two
months on the following points:
- Check that all the screws are correctly tightened
- Remove all the non expected elements (ex: stickers, clothes, ropes,…)
- Fix paint defects if the module has been damaged, using the adapted paint, specified by the manufactu-
rer.
- Replace all damaged or missing parts with a spare part recommended by the manufacturer.
- Check that all the instruction labels stuck on the modules are in condition and are readable. Replace
them if necessary.
- Check the stability of the modules. If one of them is sligthly unfixed from the foundation,
- Check that all the anchors are secure in the ground.
- Clean all dirty parts with soapy water.
Every year, it is recommended to check carefully the ground fixation. In order to do this, remove the dirt
covering the attachment plate, and inspect cautiously the wear of the fixations and of the concrete. Re-
place them if necessary. Check that the screws are firmly tightened.
Note : If the screws untighten too easily, do not hesitate to use Loctite !
WARRANTY
One full year parts and labor guarantee. Every claim regarding condition of the delivered equipment has to
be done within the legal period of the reception of the material. The warranty will not apply to:
- all degradation during the transport.
- all degradation due to use differing from which was intended.
- all degradation due to poor maintenance.
- any defect claimed after the end of the legal period.
- any damaged due to a faulty installation and assembly of the module

2
TECHNICAL DETAILS AND DRAWINGS
Height of free fall: 520 mm
Evolution zone area: 16 m²
Dimensions
Exercise space and evolution space
Dimensions

3
USER MANUAL
Precautions:
- Be careful during the access and
egress to the module
- Only one person at a time
- Do not jump on the module
Advantages:
This module is ideal:
- To strengthen legs’s and arms’s muscles
- To work on coordination
- To maintain heart fonctions
Example:
Placing your foot on the pedals. Grab the han-
dles and move alternatively your legs and
arms.
Restrictions:
- This equipment is dedicated to adults
and teenagers over 1400 mm.
- Maximum authorized weigth: 120 kg
- Not recommanded for pregnant women
and for people suffering from heart
deseases

4
FIXATION & CONCRETING
NECESSARY TOOLS (NOT INCLUDED)
INCLUDED ITEMS
Shovel Wrench 27
Dig a hole for the concrete according to the drawing above.
The dimensions of the holes are:
- Depth : 0.75 m
- Width : 0.7 m
- Length : 0.7 m
NB: All the dimensions are in millimeter
Fixing kit M18
x1 x4 x8 x8

5
FIXATION & SEALING
NECESSARY
ITEMS
- Pour concrete (EN 206-1) and stop when you are 25 cm under the surface.
- Insert the attachment plate into the concrete, ensuring it is settled horizontally.
- Assemble the plate attachments as follow:
- Let the concrete set during 3 or 4 days.
Fixing kit M18
x1 x4 x8 x8

6
FIXATION & CONCRETING
Remove the nuts and the washers from the at-
tachment plates. Mount the equipment onto the
attachment plate and fix them together thanks
to the fixing kit already used.
Fill the gap with dirt, then cover.
NECESSARY
ITEMS

7
ASSEMBLY
1– ASSEMBLY OF THE ROTATING PART
NECESSARY
ITEMS
NECESSARY TOOLS (NOT INCLUDED)
INCLUDED ITEMS
To make the assembly, follow the steps
bellow :
- Insert 2 IGUS pads in every bore (4
in total)
- Insert the assemblies on the main
frame and lock them with the covers +
spacers + washers + screws
Bushings
x8
Covers
x4
Covers
x4 x4
Spacers
Stainless Steel
Screw M10x20
x4
Raw stainless steel
washer D10
x8
Bushing
x8
Cover
x4
Cover
x4 x4
Spacer
Stainless steel
Screw M10x20
x4
Stainless steel
washer D10
x8
Torque wrench 17 Mallet
x8
SS Grub screw
M10x12
x8
SS Grub screw
M10x12

8
NOMENCLATURE
Package
N° Ref Index Designation Description Quantity Packing Method Weight (kg)
Dim.
(mm)
A1 S80102-01 CMain frame 1
Plastic
bubbles+cardb
oard 5 layers
53 1900x1375x500
A2 S80102-02 CRight arm 1
Plastic
bubbles+cardb
oard 5 layers
11 1650x300x200
A3 S80102-03 CLeft arm 1
Plastic
bubbles+cardb
oard 5 layers
11 1650x300x200
A4 S80102-09 CAccessories
Plastic
bubbles+cardb
oard 5 layers
8450x450x100
PRE-ASSEMBLED ACCESSORIES
PACKING LIST
ELLIPTICAL TRAINER
PRODUCT REF S80102 Index C UNIT
Package
N° Ref Designation Description Qty Note
A1 Stickers 1 + 1 Stuck on the structure
A2+A3 IGUS GFM-3034-26 Bushings 4
A1 Brake 1
A1 OBI6206 Balls bearings SKF 2
A1+A2
+A3 Covers 6
A1+A2
+A3 Covers 6
A1+A2
+A3
BITH1020
LITA102510
SS Screws M10x20
SS Washers 10 6 + 6
A1 PT62T Circlips D62 2
A1 SS Grub screw M10x12 8

9
ACCESSORIES PUT IN CLEAR PVC BAG
PACKING LIST
ELLIPTICAL TRAINER
PRODUCT REF S80102 Index C UNIT
Package
N° Ref Designation Description Qty Note
A4 BITH1020
LITA102510
SS Screws M10x20 +
SS Washers 10 +
Spacers M10
4 + 4 + 4 To fix the arms to the
main frame
A4 S80102-07 Fixing kit M18 8 + 8 To be put in the
ground
A4 LITA184220
TTBC18
Fixing kit fastening
accessories 8 + 8
A4 Stickers 1+1 To replace the stick-
ers if damaged
A4 IGUS GFM-3034-26 Bushings 8
A4 Covers 4
A4 Covers 4
VISA PACKING DEPARTMENT DATE :