Soho SD07 User manual

SOHODESK SD07
ASSEMBLY INSTRUCTIONS - PLEASE KEEP FOR FUTURE REFERENCE
IMPORTANT - PLEASE READ THE INSTRUCTIONS FULLY BEFORE STARTING ASSEMBLY
page 1
Dimensions
Length - 120cm
Depth - 60cm
Height - 77cm
Weight - 25,80kg
Maximum Weight Tolerance
50kg

SAFETY AND CARE ADVICE
Important - Please read these instructions fully before starting assembly
!
!
!
!
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and separate them
into their groups.
Keep children and animals away
from the work area, small parts
could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
!
!
!
!
Do not stand or put weight on the
product during assembly, this could
cause damage.
Assemble the item as close to its
final position (in the same room) as
possible.
Assemble on a soft level surface to
avoid damaging the unit or your
floor.
Parts of the assembly will be
easier with 2 people.
!We do not
recommend the use
of power drill/drivers
for inserting screws,
as this could damage
the unit. Only use the
allen key provided, or
a hand screwdriver.
!Dispose of all packaging
carefully and responsibly.
Care and maintenance
!Only clean using a damp cloth
and mild detergent, do notuse
bleach or abrasive cleaners.
!From time to time check that
there are no loose screws on this
unit.
!Do not stand on the unit.
!Do not use this unit as a step ladder.
!This product should not be discarded with household waste.
Take to your local authority waste disposal centre.
Handy Hints
!Assemble all parts and bolts loosely
during assembly, only once the product is
complete should you fully tighten the bolts.
!Regularly check and ensure that all
bolts and fittings are tightened properly.

D
BA C
page 3
Size M6 x 50 Bolt
x 10
E F
Size M6 x 40 Bolt
x 40
Size M6 x 15 Bolt
x 5
Size M6 Nut
x 1
Height Adjustable Foot x 8
( Size M6 x 25 mm )
Puller Nut 10 x 13
x 12
G
COMPONENTS - FIXINGS
PLEASE CHECK YOU HAVE ALL THE PARTS LISTED BELOW
Note : The quantities below are the correct amount to complete the assembly.
In some cases more fittings may be supplied than are required.
Tools required
Phillips screwdriver Small hammer Tape measure
Nut Sticker
x 12
H
Size M6 x 12 Allen Head Nut
x 4
I
Allen Key
Size : 4mm
x 1

COMPONENTS - PARTS
PLEASE CHECK YOU HAVE ALL THE PARTS LISTED BELOW
page 4
Desktop
1Bottom board x2 3
Middle board x2
2
Rear frame x 2
4Front frame x 2
5Beam 6
Middle bar x 2
7Top bar x 2
8Connecting rod x 2 9

page 5
F
F
F
F
F
F
F
F
F
4
4
55
Step 2
B
B
B
B
B
B
B
B
4
8
7
8
7
4
5
5
Step 1
B
ASSEMBLY INSTRUCTIONS
Carefully screw in
adjustable feet F into
the rear and front
frames and .
5
4
Align the leg frame
holes and with
the top and middle bar
and as shown in
the assembly
instruction image.
7
45
8
Once aligned, use the
M6 x 40mm bolt B
to fix the leg frames
and bars together.
Please make sure all
bolts are tight and no
gapping is visible
between the leg
frames and bars.

D
C
B
B
C
E
C
D
B
B
BB
A
A
page 6
ASSEMBLY INSTRUCTIONS
B
B
A
B
22
3
3
6
9
Step 3
B
G
G
G
G
G
Step 4
C
C
C
D
D
D
I
Align the middle and
bottom board panels
with the frame holes.
Use frame B to fix the
board panels to the
frames.
Fix bolt B to the
underside of the board
panels and through
the top and middle bar
and .
2 3
7
8
Please make sure all
bolts are tight and no
gapping is visible.
Fix beam between the left &
right constructed frames.
Make sure the beam
holes align with the top bar
holes.
6
6
8
Use bolt B to fix all
components together. Make
sure all bolts are tight and no
gapping is visible.
Repeat the same process
using the connecting rods
and C D E .
9
32
G

page 7
BB
BBA
B
A
A
BB
A
A
BABB
ASSEMBLY INSTRUCTIONS
Step 5
1
H
H
Carefully turn the desktop
upside down and place
onto a soft surface. Once
the desktop is upside
down carefully repeat
the process with the
constructed frames as
shown in the assembly
instruction image.
1
Align the constructed
frames with the predrilled
and inserted holes in the
desktop . Once all holes
are aligned use the
M6 x 50mm bolt A
M6 x 40mm bolt B to fix
the frames and wooden
desktop together.
1
Please make sure all
bolts are tight and no
gapping is visible between
the leg frames and desktop.