Sol-Expert Solar dolphin 86300 User manual

SOL-EXPERT
group
group
SOL-EXPERT
group
group
10+10+
This way you help the
environment: Please return
the parts to a suitably
certified supplier at the end
of their useful life!
Solar dolphin
Wooden construction kit, with gearbox.
Dolphins "leap" when exposed to sunlight
SOLAR
Item No.: 86300
Not a toy!

3
A
ASSEMBLY INSTRUCTIONS
Push in the gearbox from the back of the wave panel and fasten the screws and nuts with a small screwdriver.
What you will need:
M3 X 10 mm
2 x
2 x M3
1 x 1 x
1 x Attention: Make sure the sides are correctly positioned!
Wave direction Wave direction
ü
M3 X 10 mm
Front Back
Motor
M3 nut
1 cm
65 mm
Hier kannst Du die Länge der Achse messen:
01 4
2 5
3 6
0 mm60 mm 36 mm
Front Back

3
B
Screw the dolphin wheel (position it as shown in the picture) to the gearbox axle A with the M3 x 5 mm screw using the screwdriver.
Secure it in place with the wood spanner to prevent it from turning. Then apply a thin layer of glue on the wave plate (where
it is red in picture 2) and then glue it in the middle of the base plate. The 3 slots in the base plate must point forwards as in picture 3.
What you will need:
M3 X 5 mm
1 x
2 x
1 x
1 x
ü
M3 X 5 mm
111
123
Correct direction of rotation Wrong direction of rotation
0.5 cm
A
3 slots visible
1 x

Stick on the solar cell.
What you will need:
3
C
Adhesive
pad
1 x
1 x
2 x
1
1
1
4
Solar cell support
Apply some glue to the solar cell... 1
3Feed the motor cable through the solar cell support
and connect it to the solar cell. Press the button,
push in the cable, release the button - job done.
Red cable to "-", black cable to "+".
1
2
Adhesive pad
Adhesive pad
of the solar panel.
...then glue into the wave panel and
stick the adhesive pads on the back

Stick on the fish with a
little glue. Then apply the
front panel with glue and
glue it in place.
3
DAttention: Make sure the sides are correctly positioned!
ü
2 x
What you will need:
Wave direction Wave direction
1 x

Apply 4 x glue to the recesses... ...and then glue in the two side parts
3
EWhat you will need:
2 x

Apply adhesive ( ), turn the part over and glue it to A
the front panel. Glue on the crab and octopus where
you choose. Allow to dry for for 10 minutes and
you're done!!
Congratulations -
your dolphin is now
ready to leap and dive
as soon as enough
sunlight shines on the
solar panel.
Allow to
dry for
10 minutes
3
F
A
What you will need:
1 x
1 x
1 x
HINT!
A solar module generates maximum
power when placed in direct sunlight.
In the absence of direct sunlight, the power
generated is only very low. It is therefore recom-
mended that this model be placed in a sunny location.
ü
ü

More great kits available at:
www.sol-expert-group.de
SOL-EXPERT group, C.Repky
Mehlisstrasse 19 - D-88255 Baindt
Tel.: [phone] - 94115-0 - Fax: [phone]
[email protected] - www.sol-expert-group.de
Errors and changes reserved
©
Juli 2021 / Christian Repky
Please return the electronic parts
to a suitably certified supplier at
the end of their useful life!
Click here for the instructions:
Hier geht es zur Anleitung:
Cliquez ici pour les instructions:
Klik hier voor de instructies:
https://www.sol-expert-
group.de/Solar-
Produkte/Modelle-aus-
Holz/Solar-Holz-
Steckbausaetze/Solar-Delfin-
Holzbausatz::1361.html?languag
e=de
https://www.sol-expert-
group.de/Solar-products/Models-
made-of-wood/Solar-wooden-
building-kits/Solar-dolphin-
wooden-
kit::1361.html?language=en
https://www.sol-expert-
group.de/Articles-
solaires/Modeles-reduits-en-
bois/Kits-dassemblage-solaires-
en-bois/Kit-en-bois-dauphin-
solaire::1361.html?language=fr
https://www.sol-expert-
group.de/Producten-op-zonne-
energie/Modellen-van-hout/In-
elkaar-te-steken-houten-
bouwsets-op-zonne-
energie/Zonnedolfijn-houten-
kit::1361.html?language=nl
Kits from SOL-EXPERT that have you wanting more: Detailed instructions, high accuracy component fit, high quality standard!
4 0 3 7 3 7 3 8 6 3 0 0 6
Keep company address. Not suitable
for children under 3 years! - Choking
hazard due to small parts!