Sol-Expert 1818584 Instruction manual

Firmenanschrift aufbewahren -
Keep the address of the company -
Veuillez conserver l'adresse -
Adres bewaren -
Nicht geeignet für Kinder unter 3 Jahren! - Verschluckbare
Kleinteile! Not suitable for children under 3 years! -
Contains small parts! Ne convient pas pour les enfants de moins
de trois ans! - Contient de petites pièces pouvant être absorbées! Niet
geschikt voor kinderen beneden 3 jaar! - Kleine onderdelen Kunnen worden ingeslikt!
Tel.: [phone] - 94115-0 - Fax: [phone]
[email protected] - www.sol-expert-group.de
SOL-EXPERT group, C.Repky - Mehlisstrasse 19 - D-88255 Baindt
SOL-EXPERT
group
group
10+
No. 44480
MADE IN EUROPE
Parts list:
Qty. Part
Property
Check and
sort out parts!
Dimensions:
150 x 70 x 70 mm
EPP boat hull Buoyant and sturdy
Low-friction motor RF300L
Propeller Diameter: 65 mm
Motor bracket Metal
Solar cell 50 mA@ 2 - 3 V
1
1
1
1
1
You will also need: soldering iron, glue gun
CAUTION:
The glue coming out of the glue gun is very
hot. Be very careful not to get it on your
skin. If it does get on your skin, immediately
cool the area with water and seek medical
attention if the glue does not come off on ist
own. The nozzle on the glue gun also
becomes very hot during use.
Be careful not to burn yourself on it.
The tough part about hot glue:
The glue remains very hot for some time after
being applied with the glue gun.
So always wait a good 2 minutes after
applying glue to allow the glue to cool
down. Then continue.
4 037373 444809
Recommendation for children
and teenagers: Assembly and
soldering should be supervised
by an adult.
SOLDER
GLUE
&
Return the device
to a certified provider at the
end of its useful life!
GLUE
QR Codes
Cliquez ici pour les instructions:
Klik hier voor de instructies:
https://www.sol-expert-group.de/Solar-
products/Models-made-of-plastic/Building-
kits/Solar-boat-Airstream-solder-
kit::1257.html?language=en
https://www.sol-expert-group.de/Articles-
solaires/ModEles-rEduits-en-plastique/Kits-d-
039-assemblage/Bateau-solaire-Airstream-kit-
de-soudure::1257.html?language=fr
https://www.sol-expert-group.de/Producten-op-
zonne-energie/Modellen-van-
kunststof/Bouwsets/Zonneboot-Airstream-
soldeerkit::1257.html?language=nl
Click here for the instructions:
Hier geht es zur Anleitung:
https://www.sol-expert-group.de/Solar-
Produkte/Modelle-aus-
Kunststoff/Bausaetze/Solarboot-Airstream-
Loetbausatz::1257.html?language=de
Conrad No. 1818584

Attach with
hot glue
Attach with
hot glue
Attach with
hot glue
Hull Hull
Hull
Solar cell Spacer
Spacer
Spacer
Motor
Motor bracket
Side view Rear view
Solar cell
Glue the motor bracket onto the middle of the
spacer, let cool for 2 min.
Solder cable in place
Changes and error reserved, September 2018 / Christian Repky ©
A
BSlide the motor into the motor bracket and attach the propeller.
C
D E
Attach with
hot glue
Attach with
hot glue
Attention:
Solder the red cable
to the red dot!
Attach with
hot glue
Hull
Spacer
Apply hot glue to the spacer, then attach to the hull (approx. from the edge). Let cool for 2 min.
45 mm
45.00 mm
Rear round bow
15.00 mm
20.00 mm
Attach with
hot glue
Place the solar cell on top and apply hot glue all around. If the solar place is glued
in place clean on all sides, the back of the solar cell will be protected from water.
Safety notes:
Keep this manual for future reference! It contains important information.
The soldering iron, solder and the parts being soldered become very hot. Be very careful!
Always use a mat when soldering! This prevents parts from slipping.
We recommend using a soldering iron holder to set the soldering iron down safely during use.
Attach with
hot glue